Summary of Contents for Barry-Wehmiller Accraply 204RH
Page 1
AUTOMATED TAMPER-EVIDENT SEAL APPLICATOR OPERATION AND MAINTENANCE MANUAL Customer: UCB Manufacturing, Inc. Machine Serial Number: MSN07411 Manual Revision #: R01 Revision Date: 5/21/13 For service and parts, call ACCRAPLY: Phone: 905-336-8880 Toll Free: 1-800-387-6742 (System parts/drawings found in Section 2. Head parts/drawings found in Section 4.)
Page 3
CUSTOMER SERVICE AND SPARE PARTS Customer Service and Spare Parts Customer Service Our trained Service Technicians are available to provide installation and training and ensure you have fast and efficient start-up. Training your personnel in the proper operation, setup, and maintenance procedures for your Accraply labeler ensures excellent long-term performance and reliability.
Page 4
CUSTOMER SERVICE AND SPARE PARTS Recommended Spare Parts List Assembly Number Assembly Name Item Number Qty Item Name 080800-07411 Infeed, Metering Wheel 80369 Wheel, Product 603805-07411 Squaring, Assembly 117068 Sensor, Rotary Cylinder 603900-07411 Sensor, Product Standard 105039 Sensor, Retro-Reflective (Banner) 621597 Sensor, Photo Reflective (Sick) 608888-07411...
SAFETY PROCEDURES 1.1 Safety Procedures 1.1.1 General Guidelines • Read and understand your Operation and Service Manual. Understand how to operate the Labeler before using it. • Keep a regular maintenance schedule. A well maintained machine operates more efficiently. • Do not operate the Labeler unless all components have been properly installed.
SAFETY PROCEDURES 1.1.4 Machine Safety Labels This machine is equipped with safety labels. These safety labels are placed on the machine to identify areas that may be hazardous to the personal safety of the operator. Read, Understand and Follow these safety notices. The descriptions in this manual cover warning labels for machines that are covered by different regulatory codes and standards.
Page 11
SAFETY PROCEDURES Name Figure Part # Label (not actual size) Hazardous Voltage H6010-B1.whpk 119554 Electrical enclosures with a disconnect that opens the only source of power are marked with this label. The label is used for “hard wired” and corded machines. Name Figure Part #...
Page 12
SAFETY PROCEDURES Name Figure Part # Label (not actual size) Protective Earth IEC-5019a-c 850483 This label may be found inside of each electrical enclosure next to the grounding bus (protective bonding terminal). It is the protective earth (ground) symbol. ENTANGLEMENT HAZARDS - GUARDS Figure Label (not actual size) Figure...
Page 13
SAFETY PROCEDURES Figure Part # Figure Part # 1009-02.whpk 119544 1009-05.whpk 119545 Label (not actual size) Label (not actual size) Figure Part # H1143-f6.whpk 134779 Label (not actual size) Figure Part # Figure Part # 1056-ftwhpk 119550 1043-39.whpk 119551 Label (not actual size) Label (not actual size) SECTION 1: SYSTEM OPERATION...
Page 14
SAFETY PROCEDURES Figure Part # Figure Part # 1014-04whpk 104501 1143-388.whpk 121574 Label (not actual size) Label (not actual size) CUTTING HAZARDS Figure Label (not actual size) Figure Label (not actual size) 1018-82.wvpk H1007-04.wvpj Part # Part # 119552 123217 SECTION 1: SYSTEM OPERATION...
Page 15
SAFETY PROCEDURES SYMBOLS Label Example Description ISO “Warning Safety Sign”. This type of label is meant to tell you what the hazard is (e.g. Burn hazard/hot surface). ISO “Prohibition Safety Sign”. This label tells you about an action NOT to take in order to avoid a hazard (e.g.
Page 16
SAFETY PROCEDURES Name Figure Part # Label (not actual size) Belt Drive 1009B-iso 850470 Entanglement of hand/belt drive. Keep hands clear of the machine. Do not operated the labeler with the guard removed. Follow your company’s lockout procedure before servicing the machine Name Figure Part #...
Page 17
SAFETY PROCEDURES Name Figure Part # Label (not actual size) Roller Pinch Point 1156B-iso 122950 Crush of hand/roller pinch point. Keep hands clear of the machine. Do not operated the labeler with the guard removed. Follow your company’s lockout procedure before servicing the machine. Name Figure Part #...
Page 18
SAFETY PROCEDURES CUTTING HAZARDS Name Figure Part # Label (not actual size) Cutting Of Fingers Or Hand, Rotating Blade 1007B-iso 123216 Cutting of fingers or hand/rotating blade. Keep hands clear of the machine. Do not operated the labeler with the guard removed. Follow your company’s lockout procedure before servicing the machine.
Page 19
SAFETY PROCEDURES Name Figure Part # Label (not actual size) Switch Power Off Before Beginning Work 6058B-iso 119553 This label alerts the operator to switch off the electrical power before beginning any service or repair work. Follow your company’s lockout procedure before servicing the machine.
Page 20
SAFETY PROCEDURES Name Figure Part # Label (not actual size) Do Not Operate With Guard Removed 6060B-iso 850481 Do not to operate the machine with the guard removed. Name Figure Part # Label (not actual size) CE Label CE-D.75x.75 113922 This label is placed on machines that are built to meet the European Community standards.
INTRODUCTION 1.2 Introduction The purpose of this manual is to provide machine operators and maintenance personnel with the necessary information to set up, operate, and maintain the Accraply Labeler. CUSTOMER SERVICE AND SPARE PARTS Customer service contact and ordering instructions for spare parts, non-spare parts and non-engraved parts, recommended spare parts lists and the part order form.
GENERAL INFORMATION 1.3 General Information 1.3.1 Shipping and Handling 1. Position the Labeler where it is going to be used. Make sure it is properly balanced and secure. 2. Remove all banding and wrapping materials (including plastic tie wraps, cloth bands, padding, etc.) that were installed for shipping.
GENERAL INFORMATION 1.3.4 Installation Procedures 1. Place the labeler in the desired location. 2. Adjust the leveling screws on the machine base to raise the machine off it’s casters. 3. Make electrical connections (See Electrical schematics in Section 3) 4. Connect to air supply. 5.
GENERAL INFORMATION 1.3.6 General System Process NORMAL OPERATING MODE: 1. The product will be presented to the labeling system by a conveyor supplied by the customer. The product will be presented with the long side leading. The product will be transferred to the labeling system conveyor across a transfer plate.
Page 26
GENERAL INFORMATION FLOWCHART (NORMAL OPERATION): Product is transferred to Squaring cylinder conveyor across a extends. dead plate. Products are Hold down spaced by spacing cylinder extends. wheels Wipe-down Product contacts cylinder extends turn bar and wiping the labels begins turning onto the sides of the product.
GENERAL INFORMATION 1.3.8 Sensors BACKLOG SENSOR The backlog sensor is supplied by UCB. It is mounted at the infeed end of the conveyor just before the spacing wheels. If the labeling system stops for any reason, products will begin to back up at the spacing wheels which will be detected by the backlog sensor.
Page 28
GENERAL INFORMATION EJECT VERIFICATION/BIN FULL SENSOR The Eject Verification/Bin Full is a Sick photoelectric sensor with reflector and complimentary outputs for fail-safe operation. It is connected to the PLC and mounted on the reject bin. After a product fails inspection, the eject cylinder will push the product into the eject bin.
SETUP AND ADJUSTMENTS 1.4 Setup and Adjustments 1.4.1 Threading Diagram Refer to the labeling head Operator’s Manual for detailed threading instructions. The threading diagram shown here shows the correct web path and overrides the standard web path shown in the Operator’s Manual if different. SECTION 1: SYSTEM OPERATION...
SETUP AND AJDUSTMENTS 1.4.2 Label Position and Application “Y” ADJUST “Y” HAND WHEEL “X” “Z2” LABEL 2 “Z1” “X” ADJUST HAND WHEEL PRODUCT “X” CLAMP FLOW LABEL 1 “Y” CLAMP PRODUCT “X” POSITION: The “X” position of the label on the product is adjusted by loosening the “X” clamp handle on the head mount and turning the “X”...
SETUP AND ADJUSTMENTS 1.4.3 Clearance Sensor Setup The clearance sensor should be approximately 4” upstream from a product being held by the gate. APPROX. 4” GATE CLEARANCE SENSOR SECTION 1: SYSTEM OPERATION...
SETUP AND ADJUSTMENTS 1.4.4 Wipe Sensor Setup The wipe sensor must be set up as shown below. The leading edge of the product determines when the wipe sequence starts. This “start wipe point” must be slightly before the gate. There is a delay in the program that will allow the product to reach the gate before the wipe starts. The trailing edge of the product determines when the gate closes.
Page 34
OPERATING PROCEDURES 1.5 Operating Procedures 1.5.1 Controls Labeling Head controls can be found in the corresponding Operator’s manual in Section 4. CONTROL PANEL: ITEM TYPE DESCRIPTION SYSTEM REACTION & RECOVERY E/STOP Palm Button The E/Stop is mechanically maintained Machine stops. Power is cut to conveyor contact type (latching).
OPERATING PROCEDURES 1.5.2 Startup Procedure 1. Ensure there are no products on the conveyor. 2. Turn on Air at shutoff valve. 3. Turn on power at mains switch on electrical panel. 4. Press ALARM RESET button to silence the siren. 5.
OPERATING PROCEDURES 1.5.3 Alarm Indicators LIGHT STACK: YELLOW GREEN COLOUR DESCRIPTION SYSTEM REACTION SOLID RED Error/Fault System is stopped. See operator control panel for fault indicator. SOLID Head Warning (Low Label) System will continue to run. Warning from labeling head YELLOW could be low label or other head warning.
OPERATING PROCEDURES 1.5.4 Alarm List ALARM CAUSE SYSTEM REACTION & TRIGGER METHOD RECOVERY Sensor Failure Either the Wipe-Down/ Machine stops. Solid red light Disconnect one of the sensors. Evaluation sensor, or the Eject on light stack. Flashing red Verification/Bin Full sensor has SENSOR/CYL indicator light on stopped communicating with control panel.
Page 38
OPERATING PROCEDURES Clearance Pause The clearance sensor has Conveyor and spacing wheels Manually feed two products detected the next product pause. Green light on light onto the conveyor after the before the wipe-down stack flashes during pause. spacing wheel closely together. sequence has completed.
MAINTENANCE 1.6 Maintenance 1.6.1 General Maintenance Following the suggested preventative maintenance schedule will ensure long machine life and excellent performance. Immediate replacement of faulty components and repair of problems will avoid unnecessary damage. • Failure to follow a regular maintenance schedule will shorten the operating life of the equipment. •...
MAINTENANCE 1.6.2 Preventive Maintenance Follow the preventative maintenance suggestions and instructions to ensure long machine life and excellent performance. FREQUENCY ACTIVITY INSTRUCTION Daily Keep the Labeler clean Use a lint cloth, a soft bristle brush and a and free of dust and dirt. mild detergent solution.
MAINTENANCE 1.6.3 Troubleshooting Problems listed below can usually be repaired by operating personnel. If these procedures fail to produce satisfactory results, contact your ACCRAPLY Labeling Equipment System Sales Engineer or Customer Service Representative immediately. See page i for contact information. PROBLEM PROBABLE CAUSE SOLUTION...
Page 42
MAINTENANCE PROBLEM PROBABLE CAUSE SOLUTION Motor sounds Overloaded motor caused Check all solutions listed under Items “rough” or by restriction of labels and/or 2 and 5 above. vibrates. backing paper as it passes through the machine. Defective motor. Replace motor. Labels feed Translucent labels (cannot Check label opacity and notify...
AUTOMATED TAMPER-EVIDENT SEAL APPLICATOR SECTION 2: SYSTEM PARTS Customer: UCB Manufacturing, Inc. Machine Serial Number: MSN07411 Manual Revision #: R01 Revision Date: 5/21/13...
ASSEMBLY LIST 2.1 Assembly List ASSY # DESCRIPTION MSN07411 SYSTEM LAYOUT 080800-07411 INFEED, METERING WHEEL 600008-07411 STAND, CUSTOM 600106-07411 PNU, ASSEMBLY 4 STATION 600107-07411 LIGHT, STACK 600606-07411 PNU, 1 STATION SMC 2100 600895-07411 CONTROL ,ELECTRICAL 603480-07411 GUIDE, RAIL ASSEMBLY 603805-07411 SQUARING, ASSEMBLY 603900-07411 PRODUCT, SENSOR ASSEMBLY...
Page 46
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 2.2 System Parts List & Drawings MSN07411 - System Layout ITEM PART # DESCRIPTION 080800-07411 INFEED, METERING WHEEL 600008-07411 STAND, CUSTOM 600106-07411 PNU, ASSEMBLY 4 STATION 600107-07411 LIGHT, STACK 600606-07411...
Page 47
MSN07411 - System Layout ITEM 621699-07411 600107-07411 611111-07411 608888-07411 619543-07411 600606-07411 080800-07411 600106-07411 621870-07411 613200-07411 600008-07411 621700-07411 603480-07411 621598-07411 THE INF MATERIAL: AS NOTED DRAW REPROD 603900-07411 603805-07411 FINISH: WITHO 621701-07411 AS NOTED TITLE: UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN INCHES TOLERANCE 3RD ANGLE PROJ 0.00 = 0.020...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 600106-07411 - Pnu, Assembly 4 Station ITEM PART # DESCRIPTION 117056 VALVE 24VDC 117057 REGULATOR INTERFACE 117058 MANIFOLD 117059 CAP, END 117062 FILTER 600023 GAUGE, PRESSURE 600105 COVER, ELECTRICAL...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 600107-07411 - Light, Stack ITEM PART # DESCRIPTION 608415 POST, 60” LONG LIGHT STACK 118723 FLANGE, BASE (2.75) 620029 LIGHT STACK, GR, YEL, RED 620032 PIPE, LIGHTSTACK, 150MM 620522...
Page 55
600107-07411 - Light, Stack ITEM 620029 620522 620032 620523 620770 608415 118723 THE IN MATERIAL: AS NOTED REPROD FINISH: WITHO AS NOTED TITLE: UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN INCHES TOLERANCE 3RD ANGLE PROJ 0.00 = 0.020 0.000 = 0.005 1/32 FRACTIONS ANGULAR...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 600606-07411 - Pnu, 1 Station SMC 2100 ITEM PART # DESCRIPTION 117056 VALVE 24VDC 117057 REGULATOR INTERFACE 117062 FILTER 600022 BASE, VALVE 4 WAY SINGLE 600460 PLATE, MOUNT 2100 SINGLE SECTION 2: SYSTEM PARTS...
Page 57
600606-07411 - Pnu, 1 Station SMC 2100 ITEM PART # 117056 117057 600022 600460 600022 117062 117056 600460 117057 117062 117056 THE INFORMATION CON MATERIAL: AS NOTED DRAWING IS THE SOLE ACCRAPLY INC REPRODUCTION IN PART FINISH: WITHOUT THE WRITTEN P ACCRAPLY INC.
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 600895-07411 - Control, Electrical ITEM PART # DESCRIPTION 7999 SIREN, 6-28 VDC 124124 MODULE, INPUT 16 DC 124125 MODULE, OUTPUT 16 DC 126363 PANEL, ENCLOSURE 36 X 36 129260 PLATE, “B-W ACCRAPLY”...
Page 59
600895-07411 - Control, Electrical NO DRAWING AVAILABLE...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 603480-07411 - Guide, Rail Assembly ITEM PART # DESCRIPTION 601410 BLOCK, SET ADJUST 601829 RAIL, MOUNTING 602760 PLATE, ESTOP SUPPORT RAIL 602765 BLOCK, E-STOP RAIL 604647 RAIL, MTG (REW 601829 TO 10”) 618390...
Page 63
603480-07411 - Guide, Rail Assembly 621703 601829 618390 621745 621705 621746 601410 621706 621887 621045 604647 602760 621750 602765 621744 621748 621749 621747 THE INFORMATION CONTAINED IN THIS MATERIAL: AS NOTED DRAWING IS THE SOLE PROPERTY OF ACCRAPLY INC . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH: WITHOUT THE WRITTEN PERMISSION OF...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 603900-07411 - Product, Sensor Assembly ITEM PART # DESCRIPTION 101335 REFLECTOR, 2 X 2 SQUARE 105039 SENSOR, RETRO-REFLECTIVE 601408 MOUNT, PRODUCT SENSOR LOLYPOP 601409 CLAMP, SENSOR MOUNT 601410 BLOCK, SET ADJUST...
Page 65
603900-07411 - Product, Sensor Assembly ITEM PART # DESCRIPTION 101335 REFLECTOR, 2 X 2 SQUARE 105039 SENSOR, RETRO-REFLECTIVE 601408 MOUNT, PRODUCT SENSOR LOLYPOP 601409 CLAMP, SENSOR MOUNT 601410 BLOCK, SET ADJUST 612990 FLAG, SENSOR MOUNT 613727 MOUNT, REFLECTOR FLAG 614164 MOUNT, SENSOR 621597 SENSOR, RETRO REFLECTIVE...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 611111-07411 - Sensor, Low Label Assy (204) ITEM PART # DESCRIPTION 600260 SENSOR, OMRON 611480 BRACKET, LOW LABEL SENS. MTG. SECTION 2: SYSTEM PARTS...
Page 69
611111-07411 - Sensor, Low Label Assy (204) ITEM 600260 611480 THE IN MATERIAL: AS NOTED DRAW REPROD FINISH: WITHO AS NOTED TITLE: UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN INCHES TOLERANCE 3RD ANGLE PROJ 0.00 = 0.020 0.000 = 0.005 FRACTIONS 1/32 ANGULAR DETAILE...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 619543-07411 - Guard, 20X Pinch Roller ITEM PART # DESCRIPTION 615504 GUARD, PINCH ROLLER 619540 GUARD, PINCH ROLLER SIDE 1 619541 GUARD, PINCH ROLLER SIDE 2 619542 GUARD, PINCH ROLLER SIDE 3 HMB2510010A20000...
Page 71
619543-07411 - Guard, 20X Pinch Roller ITEM PART # 615504 619540 619541 615504 619542 HMB2510010A2000 HMS2510012A2000 619540 619541 619542 THE INFORMATION CONTAINED IN MATERIAL: AS NOTED DRAWING IS THE SOLE PROPERTY ACCRAPLY INC . ANY REPRODUCTION IN PART OR AS A W FINISH: WITHOUT THE WRITTEN PERMISSION AS NOTED...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 621598-07411 - Belt Conveyor 8”W x 10’ Lg ITEM PART # DESCRIPTION 2959 BELT, TIMING 187L050 600207 ADAPTER, ENCODER 600253 RING, RETAINING SSTL 0.5 SHAFT 603089 PULLEY ,TIMING 16LF050 603574...
Page 73
621598-07411 - Belt Conveyor 8”W x 10’ Lg ITEM 620136 621873 615473 611069 600207 611836 621713 621736 615432 615429 600253 615420 615424 621712 615421 615472 615471 621767 621714 840063 603574 621585 603089 620136 603089 002959 615433 THE INFO MATERIAL: DRAWI 615263 615422 603575...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 621699-07411 - Turn, Assembly ITEM PART # DESCRIPTION 601405 ROD, LONG 601408 MOUNT, PRODUCT SENSOR LOLYPOP 601409 CLAMP, SENSOR MOUNT 601410 BLOCK, SET ADJUST 614551 CYLINDER 621739...
Page 75
621699-07411 - Turn, Assembly ITEM 614551 621740 621769 601410 601408 601405 621739 601409 THE INFO MATERIAL: AS NOTED DRAWIN REPRODUC FINISH: WITHOUT AS NOTED TITLE: UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN INCHES TOLERANCE 3RD ANGLE PROJ 0.00 = 0.020 0.000 = 0.005 FRACTIONS 1/32 ANGULAR...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 621700-07411 - Wipe, Down Station ITEM PART # DESCRIPTION 89792 HANDLE 109871 CONTROL, FLOW REG OUT 1/8 601606 CYL, PNU 602493 SWITCH, REED 605708 CYLINDER, AIR-DUAL ROD 618122 SWITCH, GUARD...
Page 77
621700-07411 - Wipe, Down Station 621751 618122 621763 621740 089792 621757 621758 621866 621752 621760 621759 621769 109871 621756 621742 621741 621761 621591 621868 605708 621756 621894 621709 MATERIAL: AS NOTED 621708 FINISH: AS NOTED UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN INCHES TOLERANCE 3RD ANGLE 0.00 = 0.020...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 621701-07411 - Eject, Bin Assembly ITEM PART # DESCRIPTION 601234 REFLECTOR, 2 X 2 621594 BIN, EJECT 621595 COVER, EJECT BIN 621597 SENSOR, RETRO REFLECTIVE 621743 MOUNT, SENSOR SECTION 2: SYSTEM PARTS...
Page 79
621701-07411 - Eject, Bin Assembly ITEM 601234 621597 621743 621595 621594 MATERIAL: AS NOTED REPR FINISH: AS NOTED TITLE UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN INCHES TOLERANCE 3RD ANGLE PROJ 0.00 = 0.020 0.000 = 0.005 FRACTIONS 1/32 ANGULAR DETAI REMOVE ALL BURRS - DIMENSIONS APPLY AFTER SURFACE TREATMENTS DESIG...
For service and parts, call ACCRAPLY: Phone: 905-336-8880, Toll Free: 1-800-387-6742 SYSTEM PARTS LIST & DRAWINGS 621870-07411 - Guard, Infeed ITEM PART # DESCRIPTION 601404 CLAMP, SENSOR MOUNT 7.25 601410 BLOCK, SET ADJUST 621871 GUARD, INFEED 621869 SPACER SECTION 2: SYSTEM PARTS...
Page 81
ITEM PART # 621870-07411 - Guard, Infeed 601404 CLAMP, 601410 621871 621869 621871 621869 601410 601404 THE INFORMATION CONTAINED IN THIS MATERIAL: AS NOTED DRAWING IS THE SOLE PROPERTY OF ACCRAPLY INC . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH: WITHOUT THE WRITTEN PERMISSION OF AS NOTED...
AUTOMATED TAMPER-EVIDENT SEAL APPLICATOR SECTION 3: ELECTRICAL DRAWINGS Customer: UCB Manufacturing, Inc. Machine Serial Number: MSN07411 Manual Revision #: R01 Revision Date: 5/21/13...
Page 85
DRAWING LISTS 3.1 Electrical Drawings ELECTRICAL Drawing Number Drawing Title 200000-07411 Interface, System (Sheet 1 of 9) 200000-07411 Interface, System (Sheet 2 of 9) 200000-07411 Interface, System (Sheet 3 of 9) 200000-07411 Interface, System (Sheet 4 of 9) 200000-07411 Interface, System (Sheet 5 of 9) 200000-07411 Interface, System (Sheet 6 of 9) 200000-07411...