Download Print this page
ASP Theta 18 Quick Start Manual

ASP Theta 18 Quick Start Manual

Flying model rocket kit

Advertisement

Quick Links

Flying Model Rocket Kit
Specifications:
!
Length: 15.5"/39.4 cm
!
Diameter: 0.98"/24.9 mm
!
Weight: 1.1 oz/30 gm
!
Streamer Recovery
!
Recommended Engines:
!
!
1/2A6-2; A6-4; A8-3;
!
!
B4-4; B6-4; C6-5
!
Skill Level: Beginner
Kit EKTH - 18
This is a model rocket kit requiring
construction. Tools, adhesives,
finishing materials, launch equipment
and engines are not supplied.
P.O. Box 1408, Gibsonton, FL 33534
www.asp-rocketry.com
Estimated (calculated) altitudes:
with
1/2A6-2: 100 feet/30.5 meters
with A6-4: 235 feet/71.5 meters
with A8-3: 265 feet/81 meters
with B4-4: 510 feet/155.5 meters
with B6-4: 510 feet/155.5 meters
with C6-5: 930 feet/283.5 meters
Aerospace Speciality Products has taken reasonable
care in the design and manufacture it's products.
Aerospace Speciality Products cannot control the use
and storage of same once sold and cannot assume any
responsibility for personal or property injury resulting
from the use, storage and/or handling of its products.
The buyer assumes all risks and liabilities therefrom
and accepts the uses Aerospace Speciality Products
products on these conditions. No warranty either
expressed or implied is made regarding Aerospace
Speciality Products products, except for replacement or
repair, at Aerospace Speciality Products option, of
those products proven to be defective in manufacture
within one month from date of original purchase. For
repair or replacement under this warranty, please
contact Aerospace Speciality Products. Proof of
Purchase will be required. Note: Your state may provide
additional rights not covered by this warranty.
© 2015 Aerospace Speciality Products

Advertisement

loading
Need help?

Need help?

Do you have a question about the Theta 18 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ASP Theta 18

  • Page 1 Aerospace Speciality Products. Proof of Purchase will be required. Note: Your state may provide additional rights not covered by this warranty. P.O. Box 1408, Gibsonton, FL 33534 www.asp-rocketry.com © 2015 Aerospace Speciality Products...
  • Page 2 Apply a thin layer of glue around the outside of the tube at the 3/8" mark then slip the ring into place Theta 18 Aerospace Speciality Products...
  • Page 3 (see Figure E) - this will help to prevent from getting glue on the shock cord while you are gluing the engine mount in. Theta 18 Aerospace Speciality Products...
  • Page 4 Leading Edges Leading Edge Body! Tube End! 1/8"! Tip! Root! Views! Mark Edge Edge of Fins Trailing Edge Trailing Edges Figure I Figure J Figure K Theta 18 Aerospace Speciality Products Page 4...
  • Page 5 The bottom edge of the lug should be at the 2 1/2" mark you made on the line. Be sure the lug is parallel to the body. See Figure M. Theta 18 Aerospace Speciality Products Page 5...
  • Page 6 Firmly tape the shock cord to the streamer. Next fold the short piece of the streamer back over the shock cord and apply another piece of tape to tape the streamer to itself. Theta 18 Aerospace Speciality Products Page 6...
  • Page 7 14) At this time you may apply any decals, stickers, trim tape, etc. if desired. To protect the paint and other decorations, you may apply one or more coats of clear paint (such as Krylon Crystal Clear or similar) and allow to dry. Theta 18 Aerospace Speciality Products Page 7...
  • Page 8 (Note: the NAR Safety Code is normally included with each package of Model Rocket Engines and can also be found on the National Association of Rocketry web site at www.nar.org) KEVLAR® is a registered trademark of E.I. du Pont de Nemours and Company Theta 18 Aerospace Speciality Products Page 8...
  • Page 9 Fin Alignment Guide Tube Marking Guide Theta 18 Aerospace Speciality Products Page 9...