Table of Contents
Advertisement
Quick Links
1. BEFORE YOU BEGIN
A. INTRODUCTION
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your partic-
ular installation. This will help you avoid costly mistakes.
In addition to proper installation, read all operating and
safety instructions.
2. PRODUCT REQUIREMENTS
A. SUMMARY OF KEY REQUIREMENTS
S
Observe all local plumbing and building codes.
S
Install the unit level with the subfloor.
S
Provide properly-dimensioned framing.
S
Make sure the drain location corresponds to the
bath outlet.
S
Before you begin any work, carefully uncrate and in-
spect the new bath for any damage. Enameled cast
iron may chip; make sure there is no damage to the
new bath. If there is a problem, do not install the bath
– report the problem to the dealer immediately.
B. PRODUCT INSPECTION
Carefully uncrate and inspect the bath for damage.
AA
114014-2-
(9537)
R
CAST IRON BATH
All information in this manual is based upon the latest
Product Information available at the time of publication.
Kohler Co. reserves the right to make changes in prod-
uct characteristics, packaging, or availability at any
time without notice.
These instructions contain important care and cleaning
information – please leave these instructions for the
consumer.
REVIVAL 5'
K-873
Copyright E1995 Kohler Co.
Advertisement
Table of Contents
Related Manuals for Kohler REVIVAL K-873
Summary of Contents for Kohler REVIVAL K-873
- Page 1 Follow the sections that pertain to your partic- Kohler Co. reserves the right to make changes in prod- ular installation. This will help you avoid costly mistakes. uct characteristics, packaging, or availability at any In addition to proper installation, read all operating and time without notice.
- Page 2 Fixture dimensions are nominal and conform to toler- ances in ANSI/ASME Standard A112.19.1M. 30-3/8” No change in measurements if connected with drain illustrated. 9-3/4” 2-3/4” 30” 36” 60” 2-7/8” 1/2” 17-1/2” 2-7/8” 1/4” 1.25>132 1-1/2” O.D. 1-1/2” I.P.S. THR’D. 3” Kohler Co., Kohler WI 114014-2- (9537)
- Page 3 Disconnect the drain at the trap. Remove the old wall material. Slip boards under old bath feet to protect the floor and slide the old bath out of the recess as illustrated. Old Bath Floor Protection Boards 114014-2- (9537) Kohler Co., Kohler WI...
- Page 4 A. PARTIALLY INSTALL BATH DRAIN Install the drain to the bath according to the manufacturer’s instructions. B. PROTECT BATH UNIT Position a drop cloth or similar material in the bath bottom. Be careful not to scratch the bath. Kohler Co., Kohler WI 114014-2- (9537)
- Page 5 Open the hot and cold water supplies and check all connections for leaks. Run water in the bath and check the drain connection for leaks. 114014-2- (9537) Kohler Co., Kohler WI...
- Page 6 3/4”-7/8” outside edges of the drain shroud base. Cut line for Use the cut lines to establish the finished floor finished floor cut-out area for the drain shroud. Cut out the finished floor. Kohler Co., Kohler WI 114014-2- (9537)
- Page 7 Shroud Base Allow the silicone sealant to cure before cleaning the drain shroud and shroud base. Shroud Base 114014-2- (9537) Kohler Co., Kohler WI...
- Page 8 IMPORTANT CARE AND CLEANING INFORMATION Quality Kohler enamel is fused to red-hot cast iron. The resulting glass-hard surface and lustrous depth of color is beautiful to look at, easy to care for, and more resistant to scratching than plastic materials.
Need help?
Do you have a question about the REVIVAL K-873 and is the answer not in the manual?
Questions and answers