Related Manuals for Sun Gold Power CUT-50H
Summary of Contents for Sun Gold Power CUT-50H
- Page 1 Sun Gold Power Co.,Ltd www.sungoldpower.com CUT-50H 110/220V CUT-50L 110/220V Please read instruction manual carefully and retain for future reference...
-
Page 2: Table Of Contents
Sun Gold Power Co.,Ltd www.sungoldpower.com CONTENTS Contents & Explanation of Symbols Safety Warning Machine Description Technical Specification & Cutting Chart Front & Back Panel layout Installation Operating Precautions For PLASMA Cutting Operating Precautions Maintenance Troubleshooting & Fault Finding... -
Page 3: Safety Warning
Sun Gold Power Co.,Ltd www.sungoldpower.com SAFETY WARNING In the process of welding, there could be possibilities of injury, so please take protection into consideration during operation. For more details please read the Operator Safety Guide, which complies with the preventive requirements of the manufacturer. -
Page 4: Machine Description
Sun Gold Power Co.,Ltd www.sungoldpower.com MACHINE DESCRIPTION Thank you for purchasing our product. Plasma series is an inverter plasma machine manufactured to the highest standard. Adopting the most advanced inverter technology, it uses power Inverters and PWM technology, which works by rectifying the mains AC input voltage. The rectified input voltage is then inverted and filtered to a smooth DC current. -
Page 5: Technical Specification & Cutting Chart
Sun Gold Power Co.,Ltd www.sungoldpower.com TECHNICAL SPECIFICATIONS MODEL CUT-50H 110/220V CUT-50L 110/220V Power voltage (v AC) AC 110V AC 220V AC 110V AC 220V Rated input current (A) 36.6A 36.6A No-load voltage (V) 360V 360V 360V 360V Rated Output Voltage (V) -
Page 6: Front & Back Panel Layout
Sun Gold Power Co.,Ltd www.sungoldpower.com FRONT & REAR PANEL LAYOUT 1) Gas Meter 2) Overheat LED: The "on" overheat LED indicates that the temperature within the machine is too high. 3) Power LED: The "power" LED indicates that the machine power switch is on. - Page 7 Sun Gold Power Co.,Ltd www.sungoldpower.com FRONT & REAR PANEL LAYOUT 1) Display 2) Overheat LED: The "on" overheat LED indicates that the temperature within the machine is too high. 3) Power LED: The "power" LED indicates that the machine power switch is on.
-
Page 8: Installation
Sun Gold Power Co.,Ltd www.sungoldpower.com INSTALLATION The machine is equipped with a power voltage regulator. When power voltage moves between ± 10 % of rated voltage, it will still work normally. Should an extension cable be required (not recommended), a cord gauge of not less than 2.5mm is suggested and not longer than 10 metres. -
Page 9: Operating Precautions For Plasma Cutting
Sun Gold Power Co.,Ltd www.sungoldpower.com OPERATION Procedure for PLASMA Cutting 1. Wear your safety gear. Generally you want the same type of protective gear as when welding. Plasma has high arc voltage if the job or bench is wet and you place your hand or arm on it you can become part of the circuit... -
Page 10: Operating Precautions
Sun Gold Power Co.,Ltd www.sungoldpower.com OPERATING PRECAUTIONS Operating Environment The machine can perform in environments where conditions are dry with a max humidity of 60%. Ambient temperature should be between -10 to +40 degrees centigrade. Avoid operating machine in direct sunshine, rain, or snow. -
Page 11: Maintenance
Sun Gold Power Co.,Ltd www.sungoldpower.com MAINTENANCE WARNING! Before maintenance and checking, power must be turned off, Before opening the cover disconnect the machine from electricity! 1. Remove dust with dry, clean compressed air regularly, if the plasma machine is operated in an area where the air is polluted with smoke and dust, the machine needs to be cleaned regularly, remove dust monthly. -
Page 12: Troubleshooting & Fault Finding
Sun Gold Power Co.,Ltd www.sungoldpower.com TROUBLESHOOTING AND FAULT FINDING Notes: only attempt to repair this machine if you have knowledge and understanding of electronic components and the dangers of electricity and components holding a charge of high voltage electricity. Before maintenance contact us for authorization is suggested.
Need help?
Do you have a question about the CUT-50H and is the answer not in the manual?
Questions and answers