Weego 44s Quick Start Manual

UNDERSTANDING YOUR
Smarty Clamps ®
Your Smarty Clamps ® have a "smart" box that will help guide you
through a jump with both sight and sound. It will let you know when it
is safe to jump or if there is an error.
Solid green light, no Sound
READY
Smarty Clamps detect that you have a good connection
®
and you are ready to jump.
Flashing Green & Red Lights + Beeping
REVERSE +/-
You attached the on the wrong terminals.
Smarty Clamps ®
Make sure the BLACK clamp is attached to the battery's
NEGATIVE (-) terminal, and the RED
clamp is attached to the
battery's POSITIVE (+) terminal. If not attached properly,
Weego 44s will not let you jump your engine.
Flashing Red Light + Beeping
COOL DOWN
WAIT FOR
The Weego battery overheats after long cranks or excessive
current draw. Detach the Smarty Clamps from the battery
®
and give the unit up to 3 minutes to cool down. Then, repeat
steps 2-5 under Jump Starting Your Engine.
Solid Red Light, No Sound
SEE REVERSE
This means the vehicle's battery is too weak to even start, OR
the system voltage of your vehicle is not compatible with your
Weego 44s (for 12V vehicles ONLY).
Solid Red Light + Beeping
SEE REVERSE
There may be an engine size issue. If your engine is larger
than what we recommend, it will try to pull more power than
your Weego 44s is able to give. Please see Engine
Compatibility in the owner's manual to determine if your
engine size falls within the scope of Weego 44s.
No Light
Either you have a poor connection, or your battery is so dead
(nearly 0 volts) that your Weego clamps cannot register a
connection.
TROUBLESHOOTING
Visit www.myweego.com/support for FAQs and additional
troubleshooting inquiries.
My unit won't power on/charge/charge past a few lights
If your unit won't power on, won't take a charge OR won't charge past a few lights
then it' s been overdischarged. This can happen if the engine pulled the Weego
battery past a certain limit during a jump start. It can also happen if the Weego is
not stored with a full charge, or is not recharged every 3-6 months during storage.
Please reach out to support@myweego.com to let them know about this issue –
we'll receive and test the overdischarged Weego, then determine if we can repair
it or if it needs to be fully replaced.
The Weego won't jump start my vehicle
A few things can attribute to a failed jump start, which we listed below.
• Poor connection between the Weego clamps and vehicle battery:
the better the connection, the more likely you are to have a successful jump
• Dirty battery terminals: build up prevents all the available power from
reaching your battery
• Vehicle-specific compatibility issues: occasionally we come across a vehicle
that has unique power demands that a smaller model cannot fulfill, even
though it' s within our recommended engine range. In addition, vehicles with
heavier electronics can sometimes create issues when jumping with a Weego;
we mostly see this in push-to-start vehicles.
• Cold temperatures: Freezing temperatures create a lot of resistance in an
engine which means it can require up to 3.5X the usual amount of power to
get started; for example, an engine that usually needs 200A could need up to
700A in the extreme cold. In addition, if your Weego was stored in the cold
temps it will make it harder for the Weego to deliver its full power.
• Low-Charged Weego: it' s always best to work with full power on your
Weego if you can. Our jump starters perform better at 100% charge
than they do at 20% charge, especially when jumping larger engines.
WEEGO CUSTOMER SUPPORT
We are dedicated to providing the best possible service. To reach Customer
Support, visit myweego.com/support or email support@myweego.com.
© 2021. Weego is a division of Paris Corporation. US Patent #9692155, #D823243. All Rights Reserved. Rev 1/08
myweego.com
JUMP STARTER
QUICK START GUIDE
Model No. 44s