Page 2
Effect explanation overview Pedal control possible icon Effect type Effect explanation Parameter range PDL Delay The expression pedal controls the delay input level of this effect. InLvl Adjusts the delay input level. 0 – 100 Time Sets the delay time. 1 –...
Page 3
0 – 10 Tone Adjusts the tone. 0 – 100 Adjusts the volume. 0 – 100 ZOOM's unique noise reduction cuts noise during pauses in playing without affecting the tone. GTRIN , DETCT Sets control signal detection level. EFXIN Depth Sets the depth of noise reduction.
Page 4
FILTER SeqFLTR The sequence filter has the flavor of a Z.Vex Seek-Wah. Step Adjusts number of sequence steps. 2 – 8 PTTRN Sets effect pattern. 1 – 8 Speed Sets the speed of the modulation. 1 – 50 RESO Sets effect resonance. 0 –...
Page 5
DRIVE [ DRIVE ] TS Drive Simulation of the Ibanez TS808. Gain Adjusts the gain. 0 – 100 Boost Turns boost ON/OFF . OFF , ON Tone Adjusts the tone. 0 – 100 Adjusts the volume. 0 – 100 EP Stomp This models the Maestro Echoplex preamp.
Page 6
DRIVE OctFuzz This fuzz effect adds an octave above. Boost Adjusts the gain. 0 – 100 Color Sets the sound color. 1 , 2 Tone Adjusts the tone. 0 – 100 Adjusts the volume. 0 – 100 SpotBoost This booster enables flexible control. Boost Adjusts the gain.
Page 7
[ AMP ] MS 800 This models the sound of the Marshall JCM800 2203. Input Adjusts the input gain. LO , HI Bass Adjusts volume of low frequencies. 0 – 100 Adjusts volume of middle frequencies. 0 – 100 Treble Adjusts volume of high frequencies.
Page 8
CABINET [ CABINET ] This models the sound of a Marshall 1960 A-type cabinet with four 12" Celestion MS4x12 speakers. MIC=OFF: This tone is optimized for using amp modeling with a guitar amp. MIC=ON: This tone is optimized for using amp modeling with headphones or monitor OFF , ON speakers.
Page 9
MODULATION [ MODULATION ] Tremolo This effect varies the volume at a regular rate. TRI , TUBE , Wave Sets the modulation waveform. Depth Sets the depth of the modulation. 0 – 100 Rate Sets the speed of the modulation. 0 –...
Page 10
MODULATION / SFX This effect produces a metallic ringing sound. Adjusting the "FREQ" parameter results RingMod in a drastic change of sound character. FREQ Sets the frequency of the modulation. 1 – 50 Tone Adjusts the tone. 0 – 10 Adjusts the balance between original and effect sounds.
Page 11
DELAY [ DELAY ] Delay This long delay has a maximum length of 4000 mS. Time Sets the delay time. 1 – 4000 F .B Adjusts the feedback amount. 0 – 100 Adjusts the amount of effected sound that is mixed with the original sound. 0 –...
Page 12
REVERB [ REVERB ] This effect reproduces the ambience of a room, to create spatial depth. Size Sets the size of the space. 1 – 100 Adjusts the amount of reflection from the wall. 0 – 10 Adjusts the amount of effected sound that is mixed with the original sound. 0 –...
Page 13
PEDAL [ PEDAL ] PDL Vol The volume curve of the volume pedal can be set. Adjusts the volume. 0 – 100 Adjusts the volume when the pedal is at minimum position. 0 – 100 Adjusts the volume when the pedal is at maximum position. 0 –...
Page 14
PEDAL PDL PHSR The expression pedal controls the modulation frequency of this phaser. Rate Sets the speed of the modulation. 1 – 50 Sets the depth of the modulation. 0 – 100 Depth Sets effect resonance. 0 – 100 RESO 4 STG , 8 STG , Color...
Page 15
RHYTHM / LOOPER [ RHYTHM ] Rhythm This is a rhythm generator. GUIDE, 8Beats1 – PATTERN Select the rhythm pattern. Metro ( See Table 3 ) Adjusts the tempo. 40 – 250 Adjusts the volume. 0 – 100 [ LOOPER ] LP-MONO This is a mono looper.
Page 17
Manufacturer names and product names mentioned in this patch list are trademarks or registered trademarks of their respective owners and do not indicate any affiliation with ZOOM CORPORATION. All product and artist names are intended only to illustrate sonic characteristics that were used as reference in the development of this product.
Need help?
Do you have a question about the G5n and is the answer not in the manual?
Questions and answers