Related Manuals for Butts of Bawtry DHI0044
Summary of Contents for Butts of Bawtry DHI0044
- Page 1 INDUCTION HEATER DHI0044 Operating and Maintenance Manual www.buttsofbawtry.com Tel: 01302 710868 info@buttsofbawtry.com...
-
Page 2: Table Of Contents
INTRODUCTION ..........................4 SAFETY INSTRUCTIONS ........................4 GENERAL USE WHEN USING DHI0044 ..................4 INFORMATION SYMBOLS ......................5 SYMBOLS INDICATED HEALTH RISKS ..................6 SYMBOLS WARNING WHILE HANDLING THE DEVICE .............. 7 PERIODIC INSPECTION AND MAINTENANCE ................... 8 STORAGE ............................8 WARRANTY PROVISION ........................ - Page 3 WARRANTY CERTIFICATE ....................23...
-
Page 4: Introduction
2.1 GENERAL USE WHEN USING DHI0044 Symbols shown in this Manual warn and identify potential hazards when handling the device. Do not leave DHI0044 unattended while it is turned on. Always deactivate the unit by the master switch when not using it for heating! -
Page 5: Information Symbols
2.2 INFORMATION SYMBOLS The symbols shown below will guide you through this Manual and warn you of potential risks. If you see the symbol, be careful! Follow the instructions shown below to avoid the dangers. Read all the safety notifications and follow the instruction shown below. You will find more safety instructions in bellow. -
Page 6: Symbols Indicated Health Risks
2.3 SYMBOLS INDICATED HEALTH RISKS 2.3.1 ELECTRIC SHOCK CAUTION! Never remove casing and do any activity with the induction heater unless you have first disconnected the plug from the socket. Then wait at least 1-2 minutes after unplugging it. DO NOT OPERATE THE EQUIPMENT IN RAIN AND IN MOIST ENVIRONMENTS. CAUTION! Any and all interference with the electrical section may only be made by persons with adequate electrical engineering qualification. -
Page 7: Symbols Warning While Handling The Device
Always use protective gloves with adequate thermal resistance when working with the device. The high temperatures produced by using the DHI0044 may cause serious burns on contact with the heated part. 2.4.2 ELECTROMAGNETIC EFFECTS The electromagnetic field (EMF) may affect implanted medical devices. The device is not intended to be used by users of cardiac pacemakers or other implanted medical devices. -
Page 8: Periodic Inspection And Maintenance
Scheduling device maintenance has to consider the degree and circumstances of device use. Considerate use and preventive maintenance help prevent needless defects and malfunctions. Perform checks as per standards and law in force. Only workers with adequate electrical engineering qualifications may carry out any jobs on the device. -
Page 9: Commisioning
3. The warranty period will be extended by the time for which the device is in warranty repair. If the repair finds no defects falling under the warranty, the device owner shall pay the costs of the servicing technician’s work. 4. -
Page 10: Coolant Refilling
“E##”. In that case, refill the coolant in the tank as described above. The DHI0044 induction heater device comes with a basic focusing heating inductor. The other accessories are listed in Chapter Spare and consumption parts. -
Page 11: Dipa - Dynamic Induction Power Adjust
DIPA - Dynamic Induction Power Adjust Automatic optimum setting of required power for achieving max. efficiency, speed and long-term heating in dependence on other heating parameters. ACMS-Automatic Check And Monitor System Combines features that check and verify device functionality and condition after activation, and a feature that constantly supervises and monitors the heating running and parameters for maximum device safety and reliability. -
Page 12: Controlled Heating
Display Control indicator Heating indicator Indicator TIMER Cooling and overheating indicator 8 Encoder* The DHI0044 is not connectable. The remote control connector is not used in this model series. Position Descripton Coolant reservoir cap Handle Display Induction torch holder Encoder... -
Page 13: Activating The Device
Position Description Main switch Coolant level indicator Power cord Production label Heating indicator lamp Indicates heating status. Indicator lamp Status Green Heating in progress Yellow Warning – limited heating output Heating error – overloading Red, flashing Heating error – wrong coil ... -
Page 14: Standby
This is the initial device status, which allows turning the encoder to set the desired heating power or temperature, depending on the mode selected: Controlled power mode (CP), indicator lamp glows red – the user sets the desired heating power in ... -
Page 15: List Of Errors Messages
Error Description Power supply undervoltage Power supply overvoltage Input overcurrent 4, 5 Output overcurrent Power overload 7, 8 Output frequency out of range 9, 10, 11 Regulation error Out of coolant Hose squeezed or clogged 14 – 18 Device overheating Power supply wrong grid frequency 20-256 Device servicing errors... -
Page 21: Used Device Disposal
These devices are built using materials that contain no toxic substances or poisonous to the user. Dispose of the discarded device using a collection point intended for collection of used electric equipment. Do not dispose of the used device as ordinary waste. The company is registered in the ASEKOL collective system (under manufacturer registration no. -
Page 22: Quality Certificate
Importer: JHM BUTT & CO LTD UK Type of product: DHI0044 Seriál number: …………..…………………………………………………………………………………….. Date of final inspection: …………………………………………………………………………………………………. Inspected by: …………………………………………………………………………………………………. 1. Warranty service may only be performed by a service technician trained and authorized by the manufacturer. - Page 23 Date of sale: ___________________________________________________________________ Seller’s signature and stamp: _______________________________________________________ Record of servicing intervention made Date of acceptance of Date of repair Claim report number Employee’s signature servicing Notes:...