Table of Contents
Advertisement
Quick Links
M
ODELS
DAS1
–
1
DIS1
–
1
DIS2
–
2
DIS4
–
4
DCL
–
SINGLE WALL
FLUE
(INNER
304
316
P
:
ROJECT
P
REPARED BY
P
REPARED FOR
S
R
UBMITTAL
ECORD
D
URA
P
OSITIVE
INCH AIR INSULATED
INCH CERAMIC FIBER INSULATED
INCH CERAMIC FIBER INSULATED
INCH CERAMIC FIBER INSULATED
MATERIAL
SELECTION
WALL)
CASING
GALVALUME
:
:
|
DAS1,
DIS1,
DIS2,
DIS4,
DCL
M&G
D
V
URA
ENT
S
™
P
TACK
RO
P
S
RESSURE
YSTEMS
(OUTER
WALL)
304
441
Boiler Breeching and Stack
Generator | Engine Exhaust
Fume Venting
Fireplace Venting
J
ANUARY
2016
Advertisement
Table of Contents
Related Manuals for DuraVent DURASTACK PRO DAS1 Series
Summary of Contents for DuraVent DURASTACK PRO DAS1 Series
- Page 1 M&G ™ TACK OSITIVE RESSURE YSTEMS ODELS DAS1 – INCH AIR INSULATED DIS1 – INCH CERAMIC FIBER INSULATED DIS2 – INCH CERAMIC FIBER INSULATED DIS4 – INCH CERAMIC FIBER INSULATED – ...
-
Page 2: Section A - Code Compliance
Increase chimney or exhaust system draft loss performance due to DURAVENT single wall Model DCL and double wall models DAS1, DIS1, DIS2 and DIS4 reduced exhaust gas temperature drop. venting systems are listed by Underwriters Laboratories, Inc. (UL) in the following... -
Page 3: Section B - General Information
Openings in Floor / Wall / Roof – for ALL L12 ....11 9/16” MODELS CLEARANCE Non-Combustible Roof / Floor / Wall DuraVent Models D CL, DAS - PRO a n d DI S- PRO are primarily intended to be (in) Flue Combustible Vent Diameter Roof, Floor used in a non-combustible surrounding. - Page 4 Example: [50’ / 100] x [75°F / 100] = 0.375” Expansion If the computed expansions between the fixed points are greater than 0.375” - DuraVent recommends an adjustable or bellow length be installed. SUPPORT METHODS AND HEIGHT LIMITS Several support and guiding methods are used to anchor a chimney against upward, downward and angular displacement.
-
Page 5: Seismic Requirements
(FAR) and Half Angle Rings (HAR) may be included as components of such supplemental bracing. DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND 4 M&G ENT UPITER ANE LBANY EW www.duravent.com ... - Page 6 Apply a continuous bead of S-650 or S-2000 sealant in the V-Clamp grove of the locking band. NOTE: Sealant is supplied by DuraVent - individual tubes are marked S-650 or S-2000. See TABLE 6 for number of tubes per joint. ...
- Page 7 DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND 6 M&G ENT UPITER ANE LBANY EW www.duravent.com ...
-
Page 8: Section D-Components
others supplied DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND 7 M&G ENT UPITER ANE LBANY EW www.duravent.com ... - Page 9 3. Provide access for easy removal of Tee Caps. DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND 8 M&G ENT UPITER ANE LBANY EW www.duravent.com ...
- Page 10 Figure 23 – Elbow 3 Degree (E3) DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND 9 M&G ENT UPITER ANE LBANY EW www.duravent.com ...
- Page 11 15 3/8 44 1/4 Dimensions are in inches DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND M&G ENT UPITER ANE LBANY EW 10 www.duravent.com ...
- Page 12 Figure 29 – Tapered Increaser Adapter (TIN Ø) DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND M&G ENT UPITER ANE LBANY EW 11 www.duravent.com ...
- Page 13 Minimum distance DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND M&G ENT UPITER ANE LBANY EW 12 www.duravent.com ...
- Page 14 ½” threaded rod DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND M&G ENT UPITER ANE LBANY EW 13 www.duravent.com ...
- Page 15 Figure 39 – Flat Roof Flashing (F) DCL, DAS1, DIS1, DIS2 DIS4 UBMITTAL ECORD FOR TACK ODELS AND M&G ENT UPITER ANE LBANY EW 14 www.duravent.com ...
-
Page 16: Warranty
Do not penetrate the inner wall. RAIN CAP (RC) M&G DuraVent reserves the right to make changes at any time, without notice, in design, materials, specifications, prices. NOTE: Stack Caps are not recommended for use with engine or turbine exhausts. The...