Subscribe to Our Youtube Channel
Related Manuals for Autoplugin Therminal V2
Summary of Contents for Autoplugin Therminal V2
- Page 1 Autoplugin Therminal V2 Version 7.5 Technical Description Installation Manual Rev. A...
-
Page 2: Table Of Contents
9. Troubleshooting………………………………………………………… 10. Glossary……………………………………………………………… Kit Description The Autoplugin GSM Kit-V2 is intended for remote control of the fuel-fired heater (parking heater, fuel operated heater, pre-heater), which was factory installed on Volvo S60 (2011-), V70 (2007-), XC70 (2007-) or XC60 (2010-). The kit consist of GSM module and RCP Can-V2 module. -
Page 3: Basic Functions
6. Technical Description and Installation Manual brochure 7. User Manual brochure Basic Functions 1. Refer to the User Manual control the heater from mobile phone or smartphone. 2. RCP Can give a possibility of the remote control of the heater by the original Volvo key. -
Page 4: Plug-N-Play Connection
Open the case of GSM-module to install SIM card, as shown at the picture 1. Use screwdriver from package to remove screws. Figure 1 Plug-n-Play Connection This type of connection uses OBD-II service connector. It placed at the left lowest point of the dashboard. -
Page 5: Permanent Connection
Figure 2 Permanent connection Autoplugin GSM kit is recommended to be installed permanently in the cargo area. Detach the upholstery on left-hand side of cargo area, where fuse box is located. Take interconnection cable and connect RCP and GSM modules together. Only highlighted at the figure 2 connectors are used. -
Page 6: Additional Functions Of Rcp Can-V2
Additional Functions of RCP Can-V2 By default RCP Can is adjusted to execute basic functions, such as start and stop of the heater by the Volvo key or by additional button. To turn on additional functions (ex. battery monitoring) you may enter the module into programming mode and activate the corresponding setting. - Page 7 1.1.8 100 minutes 1.1.9 120 minutes 1.2. Limitation of the 1.2.1 10 minutes heater’s cycle 1.2.2 15 minutes operational time, in 1.2.3 20 minutes pre-heat mode 1.2.4 25 minutes 1.2.5 30 minutes 1.2.6 40 minutes 1.2.7 50 minutes 1.2.8 60 minutes 1.2.9 *70 minutes 2.1.
- Page 8 6.1. Indication of 6.1.1 *Off (only switching off the lighting) Indication of heater startup 6.1.2 Switch the lighting on for the heater 6.1.3 Switch the lighting on for 2 sec status by the 6.1.4 Switch the lighting on for 3 sec perimeter 6.1.5 Switch the lighting on for 5 sec lighting and...
-
Page 9: Troubleshooting
- Notifications are needed for the operation of Therminal application. If user sends SMS manually, notifications can be turned off by the means of RCP settings 7.3.8 and 7.4.8, or via settings of GSM modem (see User Manual for details). Troubleshooting If a run-time error occurs with the heater, RCP Can will inform you by the built-in and additional LEDs blinking about the error code. - Page 10 Unsuccessful The heater was switched Make a diagnostics of the start off spontaneously at a heater if the error is repeated startup Operation The heater was switched Make a diagnostics of the cycle too off spontaneously heater if the error is repeated short CAN-bus There is a problem with...
-
Page 11: Glossary
Glossary CAN - Control Area Network (digital network for data transfer in vehicles) DIS - Driver Information System of the instrument cluster GSM – Global System for Mobile GPRS – General packet radio service, packet oriented mobile data service LED - Light Emission Diode RCP - Remote Control Plug-in (electronic module for the heater remote control) SIM –... - Page 12 © Autoplugin ES www.autoplugin.ru...
Need help?
Do you have a question about the Therminal V2 and is the answer not in the manual?
Questions and answers