Quoizel HTH8411MB Installation Manual

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A19 Medium Base Bulb 100W Maximum, Medium Base Vintage Bulb is recommended, bulb not included.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact your original place of purchase.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
B
Crossbar
A Assembly
x 1
Arm
C
x 1
STEP 1 - Install the Crossbar
Assembly to the junction box
A. Attach the Crossbar
Assembly (A) to the outlet
box with the head of green
ground screw facing you.
Secure it with outlet box
screws (not included),
tighten until snug.
Figure 1
STEP 2 - Install Arm
A. Remove the lock ball from
the Fixture Body (D).
B. Place the hook end of the
Arm (C) into the loop on the
top of the Fixture Body (D).
Attach another end of the
Arm (C) onto the bolt on the
backplate and secure with
previously removed lock ball.
Hand tighten until snug.
Figure 2
2019 QuoizelInc.
for product cleaning tips. Go to the
20-30 minutes
Reflector
x 1
Outlet Box
Outlet Box Screws
(not included)
(Hook End)
Lock
Ball
Bolt
Backplate
visit us on-line at www.quoizel.com
Installation Guide #IS-HTH8411MB
For Style HTH8411MB
Care + Maintenance selection.
-
STEP 3 Test fitting the backplate to the Crossbar Assembly
A. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
B. Rotate the bolt and remove it from the bolt holder to open the door.
C. Remove the mounting ball from the
nipple. Place the backplate and
Fixture Body (D) over the nipple
against the wall to determine the
Fixture
correct position of the nipple.
D Body
Thread the mounting ball onto the
x 1
nipple. Adjust the nipple to allow the
backplate to rest against the wall
when held in place by
the mounting ball.
D. Remove the mounting
ball and the Fixture
Body (D). Tighten the
lock washer and the
hex nut against the
A
crossbar to secure in
place.
Green
Ground
Screw
Figure 3
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
C
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Loop
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
D
Ground wire
from outlet box
1of2
Nipple
Hex Nut and
Lock Washer
Backplate
White wire
Green Ground Screw
on the Crossbar
Door
D
Mounting Ball
Bolt
Bolt Holder
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 4
ReleasedDate:2019-01-28