Subscribe to Our Youtube Channel
Related Manuals for DONPER D250
Summary of Contents for DONPER D250
- Page 1 User Manual User Manual D250 Soft Serve Ice-Cream Machine ADDRESS: 4559 5th Street Brookshire, TX 77423 PHONE: (844) 366-7371...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ........3 SAFETY SUMMARY . -
Page 3: Introduction
INTRODUCTION TABLE OF CONTENTS Th anks for selecting the Donper D250 soft serve ice cream machine. Th e purpose of this manual is to provide you with the product specifi cations and our recommenda- tions for eff ective and normal operation of this machine in order to ensure and guar- OPERATING . -
Page 4: Safety Summary
SAFETY SUMMARY SPECIFICATIONS CAPACITY ELECTRICAL All safety regulations, local codes, and instructions that appear in the manual or on Freezing Cylinder 1.2 Qt (1.1L) Voltage 115v the equipment must be observed to ensure personal safety and to prevent damage to Hopper 4.8 Qt (4.5L) Phase... -
Page 5: Quick Start Guide
QUICK START GUIDE INSTALLATION Installation and Setup CAUTION: The machine must be placed on a level surface away from walls and other objects. Failure to comply will damage the machine and refrigeration compo- Unpack and inspect machine, parts, and accessories. nents and will void all warranties. -
Page 6: Unpacking
UNPACKING UNPACKING Unpack and Inspect Parts WARNING: Unpalletizing requires lifting. Two or more personnel should Remove all packaged parts and accessories from your machine. remove the machine from its packaging and place it in its final operating location. Failure to do so may result in severe injury or damage. Organize items on a clean table or operating area using the checklist below. -
Page 7: Prior To Operating
UNPACKING PRIOR TO OPERATING Inspect for damage immediately upon unpacking and call Donper USA Technical Aft er you have unpacked and set up your machine for use, we recommend running Service if you discover any damaged or missing parts. the “CLEAN” cycle for a few minutes with a mixture of 1-table spoon of bleach per gallon of water to ensure sanitization. -
Page 8: Operating
OPERATING OPERATING Operating the D250 is all done through the control board. On the control board there Freezing the Product are 6 buttons, each of which has its own function. Pressing and holding diff erent com- Verify machine has been recently sanitized (within 1 hour) binations of the buttons unlocks diff erent settings which the user can adjust to fi t their needs. -
Page 9: Standby/Night-Time Mode
OPERATING OPERATING Standby/Night-Time Mode Th e number displayed on the right side of the control panel above the word “SET” is the percentage of how ready the product currently is inside the right freezing cylinder based on it’s “HARDNESS SETTING”. When the machine will NOT be utilized for several hours, place it in STANDBY mode to conserve electricity and reduce product loss. -
Page 10: Standby/Night-Time Mode Details
Th e factory settings for the When the machine is placed into STANDBY MODE, the compressor and drive D250’s hardness is set at “01”. We fi nd this setting seems to be ideal for most indoor motor will power on. -
Page 11: Cup Counter
AND WASH buttons on the left side of the control panel. Pressing AUTO will Th e D250 has the ability to track the number of cups dispensed by the machine. To increase the hardness and pressing WASH will decrease the hardness. -
Page 12: Wash Mode
SETTINGS SETTINGS While the CUP COUNTER value is being displayed, you have the option to reset EXITING WASH MODE this back to zero by pressing and holding the SET button for about 15 seconds. Simply press the WASH button on the side of the machine which is currently in the WASH mode. -
Page 13: Advanced Settings
ADVANCED SETTINGS ADVANCED SETTINGS To access the ADVANCED SETTINGS confi rm your machine is in READY MODE. Press and hold the “SET” button for about 2 seconds until the numbers on the Continuing to SINGLE PRESS the SET button after “P1” has been displayed screen begin to fl ash, then release.
Need help?
Do you have a question about the D250 and is the answer not in the manual?
Questions and answers