Table of Contents
Advertisement
Press the
0
button repeatedly until
3.
("medium" water hardness range).
Press the
or
button to change the water hardness range.
@
A
4.
Possible values:
softened
™† ‹
1-soft
™† ‚
2-medium
™† ƒ
3-hard
™† „
4-very hard
™† ...
Press and hold the
button to exit basic settings.
0
5.
The change is saved.
Before first use
Before first use, heat the empty appliance for 20 minutes at
100 °C using
è
Steam. Do not open the appliance door
during this time. The appliance is automatically calibrated (see
section: Automatic calibration).
Operating the appliance
In this section, you can read about
how to fill the water tank
■
how to switch the appliance on and off
■
what to note after each cooking operation
■
Filling the water tank
When you open the appliance door, you will see the water tank
on the right-hand side.
Caution!
Use of unsuitable liquids may damage the appliance
Only use fresh tap water, softened water or uncarbonated
■
mineral water.
If your tap water is very hard, we recommend that you use
■
softened water.
Do not use distilled water, highly chlorinated tap water
■
(> 40 mg/l) or other liquids.
You can obtain information about your tap water from your
water supplier. The water hardness can be checked with the
test strips enclosed.
Fill the water tank before each use:
Open the appliance door and take out the water tank.
1.
Fill the water tank with cold water up to the "max" mark.
2.
Close the tank cover until you feel it engage.
3.
Slide in the water tank until it engages.
4.
™† ƒ
appears
-
I
II
III
IV
P D [
Fill and insert the water tank (see section: Filling the water
1.
tank).
Before using for the first time, moisten the seal in the tank
cover with a little water.
Turn the operating mode selector to
2.
Turn the temperature selector to 100 °C.
3.
Press the
button.
n
4.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and an audible
signal sounds.
To switch off the appliance, turn the operating mode and
5.
temperature selectors to
Leave the appliance door ajar until the appliance has cooled
down.
Cleaning the accessories before use
Using soapy water and a soft cloth, clean the accessories
thoroughly before first use.
Switching on the appliance
Turn the operating mode selector to the required operating
1.
mode.
Turn the temperature selector to set the temperature.
2.
Operating mode
Steam
è
Defrosting
B
A default cooking time appears in the display.
Use the
@
or
A
button to set the cooking time.
3.
Press the
button.
n
4.
The appliance heats up.
The
symbol lights up until the set temperature has been
t
reached and each time the temperature rises.
In the
è
Steam operating mode, the cooking time does not
start counting down until the heating-up time has finished.
Changing the temperature
You can change the temperature at any time. To do this, turn
the temperature selector.
Pause
Briefly press the
button to interrupt cooking (pause). The
n
cooling fan may continue running. Press the
If you open the appliance door during cooking, operation is
interrupted. Close the appliance door and press the
to restart.
If you have switched on the basic setting "Continue operation
after closing door", restarting is not required (see section:
Basic settings).
Display
Ë
If the water tank is empty, a signal sounds and the
(Fill water tank) appears. Cooking is interrupted.
Open the appliance door carefully.
1.
Hot steam will escape.
Remove the water tank, fill up to the "max" mark and slide the
2.
tank back in.
Press the
n
button.
3.
è
Steam.
.
Û
Temperature range
35 - 100 °C
35 - 60 °C
button to start.
n
n
Ë
button
symbol
7
Advertisement
Table of Contents
