Sharp 32BC2E User Manual page 18

EN
Sharpness - Increase or decrease the sharpness of the picture.
Tint - Lets you increase or decrease the level of tint
within the picture (for NTSC signal only).
Colour Temperature - Choose from the following presets.
– Standard - Default settings.
– Warm - Increases red within the picture.
– Cold - Increases blue within the picture.
– Personal - Personal RGB balance from „Expert Settings"
menu. Suggested only for advanced users.
Aspect Ratio - Picture format varies depending on the channel/broadcast.
There are a number of diff erent options to best meet your needs.
– Auto - Automatically displays the best picture format.
So the picture is in the correct position. May have
black lines at the top/bottom and/or sides.
– 4:3 - Displays the 4:3 picture in its original size.
Side bars are shown to fi ll the 16:9 screen.
– 16:9 - Fills the screen with a regular 16:9 signal.
– Zoom 1/2 - The picture is the correct proportion
but zoomed in to fi ll the screen.
– Dot by Dot (HDMI) - Will display the picture in its
original resolution without any change.
– Full Screen - Stretch signal to fi ll the screen.
Expert Settings
– Noise Reduction - Filters and reduces the
noise (interference) of the picture.
– Active Contrast - Automatically optimises the 'backlight' and
'contrast' of the picture according to the brightness of the screen.
SOUND
Sound Mode - Choose from the following presets
– Standard - Default settings
– Music - Emphasises music over voices
– Movie - Provides live and full sound for movies
– Sports - Emphasises sound for sports
– Personal - Selects your personal sound settings
DTS Studio Sound - Allows you to turn surround sound eff ect ON or OFF.
DTS DRC - Adjusts the level of dynamic range for DTS movie
soundtracks. Very loud sounds get quieter and quiet parts
get louder. Recommended for midnight listening.
Speaker - additional settings for TV speakers or external speakers.
– Digital Output - Setttings for the digital audio
output. Choose from the following options:
– Auto - Selects the best settings automatically.
– PCM - Audio stream will be processed by the TV.
– RAW - Audio stream will be processed by device connected
via digital output (soundbar, AV receiver etc.).
– Digital Audio Delay - Enables the user to adjust
sound setting to sync picture and audio for external
speakers connected via digital audio output.
– Audio Delay (ms) - Enables the user to adjust sound
setting to sync picture and audio for TV speakers.
Auto Volume Level (AVL) - When 'on' is selected, the volume
will stay at a constant level regardless of input/source.
Expert Settings
– Balance - To switch the sound between the left and right speakers.
– Equalizer - Adjusts the volume of diff erent sound
frequencies. The equalizer sound levels can only be
adjusted when the sound mode 'Personal' is selected.
– Audio Description - Additional sound track for visually impaired.
Available only on selected DTV shows.
– AD Volume - to adjust volume of Audio Description sound track
CHANNEL
DVB Antenna - Set the type of DTV signal
– Air - Terrestrial (DVB-T)
– Cable - Cable (DVB-C)
Auto Scan - Allows you to retune the television for all digital
channels, digital radio stations and analogue channels.
Analogue Manual Tuning - Allows you to
manually tune your analogue signal.
Digital Manual Tuning - Allows you to manually tune your digital signal.
Auto update channel list - if you set this option ON, channel positions,
names and frequencies will be periodically updated by the provider.
This may cause issues if you ordered channels in the list of channels
by yourself. In such case we recommend to keep this option off .
HbbTV - Allows the user to switch HbbTV on/off . To
use HbbTV, TV must be connected to the internet and
watched channel must support HbbTV service.
LCN - Set LCN to ON if you want to arrange channels by provider
preferences (only applies to DVB-T and DVB-C channels).
CAM Setting - Pay per view services require a "smartcard" to be
inserted into the TV. If you subscribe to a pay per view service the
provider will issue you with a 'CAM' and a "smartcard". The CAM can
then be inserted into the COMMON INTERFACE PORT (CI Card In). This
menu allows you to view information and change settings of CAM.
Signal Information - Information about DVB signal.
Set CAM PIN code* - Here you can pre-emptively enter CI card PIN code
to disable channel recording restrictions due to Parental control function.
Satellite Setup - This menu is only available in DVB-S2 mode. You can
select the type of satellite, your transponder and your LNB type, etc.
* - Only for devices with built in PVR function
NETWORK
Network - Select the type of network connection
- Cable (Ethernet) or Wi-Fi (Wireless).
NOTE: For connecting to the Internet with a wired connection, connect a Cat
5/Ethernet cable (not included) from the TV to your broadband modem/router.
Ethernet - This advises the connection status of the wired
network. If [OK] is pressed, another menu opens which allows
for the connection to an IPv4 or IPv6 wired network:
– Auto - Will automatically connect the TV to
your home network (recommended)
– Manual - Allows you to manually change the IP,
Netmask, Gateway and DNS information.
– Disable - TV will not use selected IP version
for connecting to the network.
Wi-Fi - This advises the connection status of the Wi Fi network. If [OK] is
pressed, another menu opens which shows all Wi-Fi networks which the
set can pick up. Select the one which you want to connect to and press
[OK].
If the network is locked, the screen will now show a
password entry screen with an on-screen keyboard.
WPS - option for alternative secure connection to the Wi-Fi network.
– Push button method - select this option and
press WPS button on your router.
– Generate a security PIN - TV will generate security
PIN which needs to be entered into router.
NOTE: The connection process may take a few minutes, please be
patient. Every time the TV is then powered on it will automatically
connect to the network, this may also take some time.
Network Test - A network connection test
Network Information - Information about the network settings
TIME
Time - Shows the date and time. After pressing [OK] while
this item is highlighted, the following options appear:
– Auto Sync - Automatically sets the time and date on the TV
set. Requires the TV to be tuned in with a digital signal and/
or an internet connection. Turn "Auto Sync" off to manually
adjust the time and date settings. If "Auto Sync" is set to off
with the time and date manually adjusted, this information
will be reset when the power to the TV is disconnected.