easymaxx NC2350/MM-2SL Manual page 3

EN
■ Protect the articles from: impacts, heat, direct sunlight, sub-
zero temperatures, moisture and wet conditions.
■ The individual LEDs cannot be replaced.
■ Do not modify the articles and do not attempt to repair them. In
the event of any damage, please contact our customer service
department.
Items Supplied
Check the items supplied for completeness and possible transport
damage. If you should fi nd any transport damage, do not (!) use
the articles, but contact the customer service department.
• Light with LEDs (2 x)
• Holder (2 x)
• Dowel and screw for wall mounting (2 x each)
• Adhesive strip (2 x)
• Instructions (1 x)
For each light you need additionally 3 batteries (1.5 V, type
AAA). They are not included in the article contents.
Attaching the Holders
When placing the lights, consider that the motion sensor
only works in a dark environment.
The holders can be put down, attached by means of the adhesive
strips or hung on the wall.
• Clean the surfaces before using the adhesive strips. To en-
sure that the adhesive strips adhere well, the surfaces must be
clean, free of dust and grease.
• For hanging on the wall, there is an eyelet on the bottom of
each holder. You can use the supplied dowels and screws or
any other fi xing material suitable for the wall. Before drilling,
ensure that there are no pipes or cables behind the in-
tended drilling point!
Inserting Batteries
NOTICE!
■ Use only the battery type specifi ed in the "Technical Data".
■ Always replace all batteries together. Do not use batteries of
different types or brands, or batteries with different capacities.
Before inserting the batteries, check whether the contacts in the
articles and on the batteries are clean, and clean them if neces-
sary.
1. Twist the two halves of a lamp in opposite directions to open
the lamp.
2. Insert three 1.5 V batteries of the AAA type. Pay attention to
the correct polarity (+ / –).
3. Put the two halves of the lamp back together, and twist them
against one another to secure them in place.
Use
1. Switching on – Slide the On / Off switch to one of the follow-
ing positions:
AUTO: The light switches on automatically when the motion
sensor registers a movement. The light switches off again after
around 30 seconds without registering a movement.
ON: The light is permanently switched on.
2. Positioning – Insert the lamp into the holder, where it is held
by magnets, and adjust it to the position you want.
3. Switching off – Slide the On / Off switch to the OFF position.
If the performance of the lights diminishes or they start to fl icker,
the batteries should be replaced.
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.
Article number: 05363
Cleaning
NOTICE!
■ Do not use any corrosive or abrasive cleaning agents or scour-
ing sponges to clean the articles. The surfaces could be dam-
aged.
Dust off the articles with a soft, dry cloth to clean them. More in-
tense soiling can be wiped off with a damp cloth.
Technical Data
Article number:
Model number:
Power supply:
Power:
Protection class:
Nominal luminous fl ux: 130 lm
Motion sensor:
Manual ID:
Disposal
Dispose of the packaging material in an environmentally
friendly manner so that it can be recycled.
These articles are governed by the European Directive
2012/19/EU on waste electrical and electronic equipment
(WEEE). Do not dispose of these articles as normal
domestic waste, but rather in an environmentally friendly
manner via an offi cially approved waste disposal company.
Batteries should be removed before the articles are
disposed of and should be disposed of separately from the
articles at suitable collection points.
Customer Service / Importer:
All rights reserved.
3
05363
NC2350/MM-2SL
4,5 V DC (3 x 1.5 V battery, AAA type)
max. 3 W
III
Coverage angle: approx. 120°
Range: max. 5 m
Lighting time: 30 s
Z 05363 M DS V1 1018
✆
+49 38851 314650 *)
Instructions