Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Craftex CT191
Summary of Contents for Craftex CT191
- Page 1 CT191 10” WET BENCH GRINDER USER MANUAL Version 1.0...
-
Page 2: Table Of Contents
TABLE OF CONTENTS General Safety Instructions for Machines ............... 3 Specific Safety Instructions..................4 CT191 Features ...................... 5 Physical Features ....................6 Proper Grounding ....................7 Un-Packing ......................8 Grinding Wheel ....................... 8 Grinding Surface ..................... 9 Test Run ......................... 9 Water Reservoir ...................... -
Page 3: General Safety Instructions For Machines
GENERAL SAFETY INSTRUCTIONS FOR MACHINES Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedures at all times. ALWAYS read and understand the NEVER leave a tool unattended while it user manual before operating the is in operation. -
Page 4: Specific Safety Instructions
CT191 - 10” WET BENCH GRINDER SPECIFIC SAFETY INSTRUCTIONS ALWAYS read and understand the NEVER LEAVE the grinder unattended user manual before operating the while it is running. grinder. MAKE SURE to do a test on the MAKE SURE you are wearing safety... -
Page 5: Ct191 Features
FEATURES MODEL CT191 - 10” WET BENCH GRINDER As part of the growing line of Craftex woodworking equipment, we are proud to offer the CT191, a 10” Wet Bench Grinder. The Craftex name guarantees Craft Excellence. By following the instructions and procedures laid out in this user manual, you will receive years of excellent service and satisfaction. -
Page 6: Physical Features
CT191 - 10” WET BENCH GRINDER PHYSICAL FEATURES Grinding Jig Leather Stropping Horizontal Mount Universal Wheel with Knobs Holder Vertical Mount Grinding with Knobs Wheel Water Reservoir Bilateral ON/OFF Switch... -
Page 7: Proper Grounding
It is strongly recommended not to use resistance for electric current to reduce the extension cords with your CT191. Always risk of electric shock. try to position your machine close to the power source so that you do not need to Make sure the cord is plugged into a use extension cords. -
Page 8: Unpacking
UNPACKING GRINDING WHEEL The machine is properly packaged and The CT191 comes with a 10” diameter, 220 shipped completely in carton for safe grit aluminum oxide grinding wheel. The transportation. When unpacking, carefully grinding wheel should inspected inspect the carton and ensure that nothing properly before installation. -
Page 9: Grinding Surface
GRINDING SURFACE TEST RUN The grinding surface of the wheel should be Once you have assembled and inspected parallel with the universal support. the machine it is then time to do a test run and see if the machine powers up and runs Make sure the switch is in the OFF position properly. -
Page 10: Water Reservoir
WATER RESERVOIR UNIVERSAL SUPPORT The CT191 is equipped with a universal The CT191 is a wet grinder and is equipped support which can be mounted on the with a water reservoir. Do no attempt to grinder in horizontal or vertical position perform grinding on this machine without depending on the grinding job. -
Page 11: Grinding Against The Rotation Of The Wheel
AGAINST THE ROTATION OF THE GRINDING JIG WHEEL The grinding jig provided with the CT191 is Grinding against the rotation of the wheel used for securing a variety of tools, and can removes a large amount of material in a... -
Page 12: Angle Guide
Position the angle guide on the grinding ANGLE GUIDE wheel with the side having the best fit measuring notch as shown in figure-10. Your CT191 grinder comes with an angle guide allowing you to find the cutting angle of your tools. HONING COMPOUND Using the angle guide is simple and easy. -
Page 13: Wheel Dressing
WHEEL DRESSING REPLACING THE GRINDING WHEEL Depending on the type of grinding you do, the grinding wheel may require periodic Make sure the switch is in the OFF position dressing. and the cord is disconnected from the power sourc. A variety of dressing tools are available (not included) and can be used to restore the Loosen the nut shown in figure-11 securing abrasive quality of the wheel surface and... -
Page 17: Warranty
This warranty shall not apply to consumable products such as blades, bits, belts, cutters, chisels, punches etceteras. Craftex shall in no event be liable for injuries, accidental or otherwise, death to persons or damage to property or for incidental contingent, special or consequential damages arising from the use of our products.
Need help?
Do you have a question about the CT191 and is the answer not in the manual?
Questions and answers