Download Print this page
Seconique 400-401-173 Assembly Instructions Manual

Seconique 400-401-173 Assembly Instructions Manual

Grey salvador 1+4 tile top dining table

Advertisement

Quick Links

SEC/SW/07/21/KK1
GREY
SALVADOR 1+4 TILE TOP
DINING TABLE
ASSEMBLY INSTRUCTIONS
IMPORTANT
FOR DOMESTIC USE ONLY
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped o ffimmediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
Page 01

Advertisement

loading

Summary of Contents for Seconique 400-401-173

  • Page 1 SEC/SW/07/21/KK1 GREY SALVADOR 1+4 TILE TOP DINING TABLE ASSEMBLY INSTRUCTIONS IMPORTANT FOR DOMESTIC USE ONLY PLEASE READ BEFORE YOU CONTINUE FURTHER CARE AND MAINTENANCE After unpacking this product please keep the original packaging in case it needs to be returned for any reason. •...
  • Page 2 SEC/SW/07/21/KK1 YELLOW BLUE BLUE YELLOW * Use of power tools to assemble this product will invalidate * Please check contents and read the instructions before commencing assembly. any claim and damage this product making it unsafe !!! * Assemble this product following the enclosed instructions carefully. * Please assemble on a clean soft surface to avoid damage.
  • Page 3 SEC/SW/07/21/KK1 FITTINGS GLUE Ø7 x 100 Ø7 x 70 3,5 x 35 10 x 40 TOOLS REQUIRED Page 03...
  • Page 4 SEC/SW/07/21/KK1 STEP 1 PARTS REQUIRED LONG FRAME SIDE SHORT FRAME SIDE HARDWARE REQUIRED 10 x 40 TOOLS REQUIRED Please assemble on Glue must be added to a clean soft surface the dowel holes on to avoid damage. parts 4 and 5. STEP 2 Ø...
  • Page 5 SEC/SW/07/21/KK1 STEP 3 Ø 7 x 100 PARTS REQUIRED LONG FRAME SIDE Ø 7 x 70 YELLOW HARDWARE REQUIRED BLUE Ø7 x 70 GLUE TOOLS REQUIRED Please assemble on Glue must be added to a clean soft surface the dowel holes on to avoid damage.
  • Page 6: Hardware Required

    SEC/SW/07/21/KK1 STEP 5 PARTS REQUIRED TABLE TOP HARDWARE REQUIRED 3,5 x 35 TOOLS REQUIRED Please assemble on a clean soft surface to avoid damage. STEP 6 PARTS REQUIRED HARDWARE REQUIRED TOOLS REQUIRED Page 06...
  • Page 7: Care And Maintenance

    SEC/SH/08/21/KK1 GREY SALVADOR 1+4 DINING CHAIR ASSEMBLY INSTRUCTIONS IMPORTANT FOR DOMESTIC USE ONLY PLEASE READ BEFORE YOU CONTINUE FURTHER CARE AND MAINTENANCE After unpacking this product please keep the original packaging in case it needs to be returned for any reason. •...
  • Page 8 SEC/SH/08/21/KK1 * Use of power tools to assemble this product will invalidate * Please check contents and read the instructions before commencing assembly. any claim and damage this product making it unsafe !!! * Assemble this product following the enclosed instructions carefully. * Please assemble on a clean soft surface to avoid damage.
  • Page 9: Tools Required

    SEC/SH/08/21/KK1 FITTINGS GLUE 10,0 x 40 Ø 7 x 80 4,0 x 40 Ø 7 x 60 3,5 x 35 TOOLS REQUIRED Page 03...
  • Page 10 SEC/SH/08/21/KK1 STEP 1 PARTS REQUIRED 03 - STRETCHER 04 - SIDE SEAT RAIL HARDWARE REQUIRED GLUE 10,0 x 40 TOOLS REQUIRED Please assemble on Glue must be added to a clean soft surface the dowel holes on to avoid damage. parts 03 and 04.
  • Page 11: Parts Required

    SEC/SH/08/21/KK1 STEP 3 PARTS REQUIRED Ø 7 x 80 BACK/FRONT RAIL BACK RAIL Ø 7 x 60 HARDWARE REQUIRED Ø 7 x 90 TOOLS REQUIRED Please assemble on a clean soft surface to avoid damage. STEP 4 Ø 7 x 80 PARTS REQUIRED Ø...
  • Page 12 SEC/SH/08/21/KK1 STEP 5 PARTS REQUIRED HARDWARE REQUIRED 3,5 x 35 TOOLS REQUIRED Please assemble on a clean soft surface to avoid damage. STEP 6 PARTS REQUIRED HARDWARE REQUIRED TOOLS REQUIRED Please assemble on a clean soft surface to avoid damage. Page 06...