Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ClearSpan 106177
Summary of Contents for ClearSpan 106177
- Page 1 CLEARSPAN VALUE LINE ™ ClearSpan ™ Round Style Storage Master Photo may show a different but similar model. ©2008 ClearSpan™ All Rights Reserved. Reproduction STK# DIMENSIONS is prohibited without permission. 106177 14' W x 10' H x 25' L Revision date: 06.21.08...
-
Page 2: Safety Precautions
• Never erect the structure under power lines. • Identify whether underground cables and pipes are Thank you for purchasing this ClearSpan™ shelter. When present before preparing the site or anchoring the properly assembled and maintained, this product will structure. -
Page 3: Assembly Procedure
These words and phrases are common to most joints and to fasten brackets to rafters. ClearSpan™ shelters and identify the different parts of the shelter. (Some are used in this document. Others may not apply to this particular shelter.) These terms describe the shipped parts and can also be found on the materials list/spec sheets included with the shipment. -
Page 4: Required Tools
CLEARSPAN VALUE LINE ™ REQUIRED TOOLS The following list identifies the main tools needed to Space below is reserved for customer notes. assemble the shelter. Additional tools and supports may be needed depending on the structure, location, and application. •... - Page 5 CLEARSPAN VALUE LINE ™ The following graphics and photos will help you identify the different parts and show you how they are used. (Not all parts are shown.) 10015106 CC6212 FA4482B QH1400 103396 103395 T-fitting Fabric Clip Band Clamp Universal Joint...
- Page 6 CLEARSPAN VALUE LINE ™ Round Style Storage Master OVERVIEW This section is an overview of the process for assembling your Round Style Storage Master. For details, please see section, Assembling the Round Style Storage Master Components. See illustration below to identify main parts of shelter.
-
Page 7: Rafter Assembly
CLEARSPAN VALUE LINE ™ LAY OUT THE BUILDING SITE ASSEMBLING THE ROUND STYLE STORAGE MASTER COMPONENTS After the site is prepared, identify the location of the shelter NOTE: Assistance is required to assemble the shelter. corners helps to square the frame after it is assembled. - Page 8 CLEARSPAN VALUE LINE ™ NOTE: All clamps must be positioned as shown. Use RAFTER ASSEMBLY (CONTINUED) a piece of duct tape to keep the clamps from sliding 3. With the main rafter pipes seated at each joint and the when the rafter is set in place.
-
Page 9: Frame Assembly
CLEARSPAN VALUE LINE ™ FRAME ASSEMBLY 3. Position an inside rafter from the end rafter using an on-center, rafter-to-rafter spacing of 5'. (Another person Gather the parts is required to hold the rafter in position.) • All rafter assemblies •... - Page 10 CLEARSPAN VALUE LINE ™ FRAME ASSEMBLY (CONTINUED) NOTE: If the last end rafter is plumb and the purlin run extends beyond the end of the rafter, cut the last 7. Move to the lower end of the rafters and position the section of purlin pipe to the required length.
- Page 11 CLEARSPAN VALUE LINE ™ Strut Assembly Procedure SQUARE THE ASSEMBLED FRAME Gather the parts 1. After the rafter assembly is complete, verify that the band clamps are in the proper locations. See diagram • Measuring tape below. • Tek Screws...
- Page 12 CLEARSPAN VALUE LINE ™ END CONDUITS ASSEMBLY PREPARE END PANELS Gather the parts: CAUTION: To prevent damage, do not install end panels on a windy day. • Pipe 1.315'' x 75'' swaged (4). Gather the parts: • Pipe 1.315'' x 22.5'' plain (2). Trim to fit.
- Page 13 CLEARSPAN VALUE LINE ™ ATTACH END CONDUIT ASSEMBLIES ATTACH END PANEL ASSEMBLIES Gather the parts: 1. Verify that the end conduit of end panel is properly inserted into the T-fittings. • End panel assemblies • Fabric clips (Divide clips equally for both end panels;...
- Page 14 CLEARSPAN VALUE LINE ™ INSTALL ROLL-UP CRANK ASSEMBLY 5. Secure the extension pipe (73.5" plain pipe) to the remaining end of the universal joint using a Tek screw. Gather the parts: • Pipe 1.315" x 75" swaged • Pipe 1.315" x 73.5" plain •...
- Page 15 CLEARSPAN VALUE LINE ™ PREPARE MAIN COVER 2. Assemble two main cover conduits. Start each conduit assembly with one plain pipe and add swaged pipes to Gather the parts: arrive at the correct length. This conduit is identical to the purlins that are attached to the frame.
- Page 16 CLEARSPAN VALUE LINE ™ ATTACH MAIN COVER 4. Once the main cover is pulled into position, center the cover on the frame and remove the ropes. Loosely Gather the parts: secure the ends of the cover to the ratchets attached to the front and back end panel conduits.
- Page 17 For replacement or missing parts, call 1-800-245-9881 for assistance. NOTE: With the exception of Truss Arch buildings, ClearSpan™ shelters and greenhouses do not have any tested loading criteria. NOTE: It may be necessary to remove excess strap if it binds up in the ratchet.
- Page 18 CLEARSPAN VALUE LINE ™ QUICK START GUIDE 14' Wide Round Style Storage Master Revision date: 06.21.08...
- Page 19 CLEARSPAN VALUE LINE ™ Revision date: 06.21.08...
- Page 20 CLEARSPAN VALUE LINE ™ Revision date: 06.21.08...
- Page 21 CLEARSPAN VALUE LINE ™ Revision date: 06.21.08...
- Page 22 CLEARSPAN VALUE LINE ™ Revision date: 06.21.08...
- Page 23 CLEARSPAN VALUE LINE ™ Space below is reserved for customer notes. Revision date: 06.21.08...
Need help?
Do you have a question about the 106177 and is the answer not in the manual?
Questions and answers