Related Manuals for Beko DVN05Q20W
Summary of Contents for Beko DVN05Q20W
- Page 1 Dishwasher User’s Manual DVN04X20W DVN04320W DVN05Q20W DVN05C20W DVN04X20S DVN04320S DVN05R20W DVN05R20B DVN04X20B DVN04320B DVN05R20S 15 9168 0100_AB_BEKO_A6_EN/ 17-06-20.(10:39)
- Page 2 Dear Customer, Please read this user manual before using the product. Thank you for choosing this Beko product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents before using the product.
-
Page 3: Table Of Contents
CONTENTS 1 SAFETY INSTRUCTIONS Lower Basket Glass Holder ......24 Lower basket multipurpose / height adjustable Intended Use ............. 4 service rack ............. 25 Safety for children, vulnerable persons and pets 4 Upper basket height adjustable rack ....26 Electrical safety ..........5 Lower basket bottle wire ........ -
Page 4: Safety Instructions
This product must be used to Safety Instructions do the domestic type dishes • This section contains safety only. instructions that will help get This product is not suitable for protected against risks of commercial or collective use. personal injury or property damage. -
Page 5: Electrical Safety
Cleaning and user Do not use extension cords, maintenance works should multi-sockets or adapters to not be performed by children operate the product. unless they are supervised by Plug must be easily someone. accessible. If this is not Keep packaging materials possible, the electrical away from children. -
Page 6: Installation Safety
squeezed or crushed while serious burns and injuries, placing the product into its and harm your furniture. location after installation or Do not install the product cleaning procedures. close to heat sources (heater, stove and etc.) or under the Installation Safety cooking area of a hob. -
Page 7: Operational Safety
hose set. Do not make extension baskets. Do not sit or put at the hoses. other loads on the door; otherwise, the product may NOTICE Connect the water inlet tilt. hose directly to the water tap. Maximum washing capacity Pressure coming from the tap of the product is stated in the should be 0.03 MPa (0.3 bars) section called “Technical... -
Page 8: Maintenance And Cleaning Safety
Maintenance and cleaning Environmental safety Instructions Do not wash the product by Compliance with WEEE spreading or pouring water Directive and Disposing of onto it. the Waste Product Do not use sharp or abrasive This product complies with tools when cleaning the EU WEEE Directive (2012/19/ product. -
Page 9: Package Information
Package information Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities. -
Page 10: Technical Specifications
Note for test institutions: Technical specifications Data required for performance tests shall be provided upon request. Requests can Maximum washing capacity (check the be e-mailed to the following address: energy label and Programme data and dishwasher@standardloading.com average consumption values table given Do not forget to provide the code, stock on Quick Guide. -
Page 11: Your Dishwasher
Your dishwasher Overview 1. Upper basket 2. Upper impeller 3. Lower impeller 4. Cutlery basket (depends on model) 5. Door 6. Rating Label 7. Control panel 8. Detergent dispenser 9. Lower basket 10. Filters 11. Salt reservoir lid 12. Upper basket rail 13. -
Page 12: Installation
Installation Appropriate installation location In the area where this product is Read “Safety Instructions” section first! installed, there must not be a lockable, Installation procedures must always be sliding or hinged door that will restrict performed by the manufacturer, authorised full opening of the product’s door. -
Page 13: Aquasafe
Permitted water temperature: up to Aquasafe+ 25°C ( 60°C for products equipped (depends on the model) with Aquasafe+; please refer to The Aquasafe+ system protects against Aquasafe+ section ) water leaks that may occur at the hose The dishwasher may not be connected to inlet.Water contact with the valve box of open warm water devices or flow-through the system must be avoided to prevent... -
Page 14: Connection To The Drain
Connection to the drain Electrical connection Water discharge hose can directly be Connect the product to a grounded connected to the drain hole or sink’s outlet protected by a fuse complying drainage. See the installation manual with the values in the "Technical supplied with your machine for detailed specifications"... -
Page 15: Fitting A Different Plug
pin face of the plug. Fuse covers are available from any good electrical store. Fitting a different plug As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug, proceed as follows: Connect the green - yellow or green (earth) wire to the terminal in the plug... -
Page 16: Preparation
Read “Quick Guide - Adjusting Water Preparation Softening System” before this section! The regeneration of the water softening Read “Safety Instructions” section first! system can be done in all programmes during drying step. When regeneration Tips for energy saving occurs, duration, energy and water Following information will help you use the consumption of the programme increase. -
Page 17: Adding Salt
Adding salt Water softening system needs to be regenerated in order for the product to operate with the same performance continuously. Dishwasher salt is used for this purpose. Use only special softening salts produced particularly for the dishwashers in your machine. You can put about 2 kg of softening It is recommended to use granule- or salt into the salt reservoir. - Page 18 further questions. using detergent tablets. Do not put solvents into the detergent dispenser. There is the risk of explosion! Put the detergent into the detergent dispenser just before operating the machine as illustrated below. 1. Push the latch to right to open the detergent dispenser lid (A).
-
Page 19: Tablet Detergents
temperature and time. 2. Set the water hardness to the highest level and perform an empty run. Tablet detergents 3. After the empty washing cycle, review the user manual and readjust the water In addition to the conventional tablet hardness level so as to suit the water detergents, there are also commercially supply. -
Page 20: Items Not Suitable For Washing In The Dishwasher
3. Slightly press the point (B) of the Decorative prints of chinaware as well reservoir lid to close it. as aluminium and silver items may get discoloured or tarnished after washing in the dishwasher just as it happens in handwashing as well. Some delicate glass types and crystals may become dull in time. - Page 21 Suggestions for loading the dishwasher Improper Loading Of Dishware Lower basket Upper basket Improper Loading Of Dishware 21/EN...
-
Page 22: Cutlery Basket
Cutlery basket Cutlery basket (depends on model) (depends on model) Cutlery basket is designed to wash your Cutlery basket is designed to wash your dishes such as knife, fork, spoon, etc. in an dishes such as knife, fork, spoon, etc. in an efficient manner. -
Page 23: Collapsible Lower Basket Tines
Collapsible lower basket tines Collapsible lower basket tines (depends on model) (depends on model) There are foldable tines (A) located at There are foldable tines (A) located at the lower basket of the machine are the lower basket of the machine are designed for an easier placement of large designed for an easier placement of large pieces such as pans, bowls, etc. -
Page 24: Tray Wash Supports
Tray Wash Supports SoftTouch Accessory (depends on model) (depends on model) Use the supports to wash trays in the The SoftTouch Accessory found in the bottom basket. lower basket of your machine enables a See the Auxiliary functions section for safe washing for your fragile glasses. -
Page 25: Lower Basket Multipurpose / Height Adjustable Service Rack
Lower basket multipurpose / To close the racks: 1. Fold the rack (A). height adjustable service rack 2. Slide the rack up (B). (depends on model) This accessory located at the lower basket 3. Put the rack in vertical position (C). of your machine allows you to easily wash 4. -
Page 26: Upper Basket Height Adjustable Rack
Upper basket height adjustable Upper basket multipurpose rack service rack (depends on model) (depends on model) Use the lower and upper parts of the height This accessory located at the upper basket adjustable racks in the upper basket of of your machine allows you to easily wash the machine by sliding them down or up pieces such as extra long ladles and bread according to the heights of the glasses,... -
Page 27: Adjusting The Height Of The Upper Basket
Adjusting the height of the upper To lower the basket, while it is in the uppermost position; basket 1. Hold the upper basket wires with both (depends on model) hands, slightly lift up the basket and The upper basket height adjustment simultaneously push and release the mechanism has been designed for you to latches shown in the figure (B). -
Page 28: Height Setting With Empty Basket
Height setting with empty basket Collapsible upper basket wires (depends on model) (depends on model) In this model, the height setting of the You can use collapsible wires when you upper basket may be changed using the need a larger space for your dishes in the wheels which are mounted at two different upper basket of your machine. -
Page 29: Ceiling Cutlery Basket
Ceiling cutlery basket (depends on model) Ceiling cutlery basket is designed to wash your cutlery items such as forks, spoons and etc. by placing them between the bars on the basket. When the central tray is in the lower position, you can load long/high items such as coffee cups, ladles, etc. -
Page 30: Operation Of The Product
Operation of the product Auxiliary functions Read “Safety Instructions” section first! Washing programmes of your dishwasher Read “Quick Quide” before this are designed to obtain the best cleaning section. effect, considering the type of the soiling, Keys soiling degree and properties of the dishes to be washed. - Page 31 Half Load function If you have used the Tablet features (Depends on model) during the last washing programme It is used to operate the machine without you used, Tablet function will remain loading it completely. active in the next washing programme 1.
-
Page 32: Programming The Washing Period
SelfDry Floor illumination (Depends on the Model) Warning to show that machine is in “SelfDry” feature of your machine increases washing phase drying efficiency of your machine and saves (depends on the model) energy. There are two options: "OFF" and Your machine reflects a light to the floor "ON". -
Page 33: Starting Of The Program
To cancel the delay function: program you have selected is complete. When you press the Start / Hold / Cancel Cancelling the program key for 3 seconds while the delay function is active, the delay process shall be 1. Press the Start / Hold / Cancel key for cancelled. -
Page 34: Setting The Rinse Aid Amount
Setting the Rinse aid Amount End of Program 1. While the Program Selection Knob is Program End indicator illuminates when the “Off”, press and hold the Half Load/ washing program has ended. Tablet function key of your machine 1. Turn off your machine with the On-Off / and rotate the Program Selection Program Selection knob. -
Page 35: Maintenance And Cleaning
Maintenance and Cleaning the filters Clean the filters at least once a week in cleaning order for the machine operates efficiently. Read “Safety Instructions” section first! Check if food residues are left on the filters. Unplug the product and turn off the If there are food residues on filters, take tap before attempting any cleaning them out and clean well under running... -
Page 36: Cleaning The Hose Filter
Cleaning the hose filter Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation (such as sand, dirt, rust, etc.) can be prevented by means of the filter attached to the water inlet hose. Check the filter and the hose regularly and clean them if necessary. -
Page 37: Cleaning The Impellers
Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently. Lower impeller Do not try to rotate the impeller by Check if the holes on the lower impeller (1) holding its ends. Trying to rotate the are clogged. -
Page 38: Troubleshooting
Troubleshooting Machine does not start. • Power cable is unplugged. >>> Check if the power cable is plugged in. • Fuse is blown. >>> Check the fuses in your house. • Water is cut. >>> Make sure that the water inlet tap is open. •... - Page 39 • Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine. • Machine is unloaded right after the programme is over. >>> Do not unload your machine right after washing process is completed.
- Page 40 There is a different odour in the machine A new machine has a peculiar odour. It will fade out after a couple of washes. • Filters are clogged. >>> Check if the filter system is clean. Clean the filter system regularly as illustrated in section “Cleaning and Care”.
- Page 41 • Opening of the detergent dispenser lid is prevented during washing. >>> Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers. • Detergent is stored under unsuitable conditions. >>> If you are using powder detergent, do not store the detergent package in humid places.
- Page 42 Foam forms in the machine. • Dishes are washed with hand-wash detergent by hand but not rinsed before placing them into the machine. >>> Hand-wash detergents do not contain antifoam. There is no need to hand-wash the dishes before placing them into the machine. Removing the coarse soil on the dishes under tap water, with a tissue paper or fork will be sufficient.
-
Page 43: Guarantee
Repairs necessary as a direct or indirect result of: Accidental damage, misuse or abuse of a product. An attempted repair of a product by anyone other than a Beko Approved Engineer (the “Engineer”). Installation or use of a product where such installation or use fails to meet the requirements contained in this guarantee or the User Instructions Booklet. - Page 44 • Repairs to a product operated at any time on commercial or non-residential household premises (unless we have previously agreed to the installation environment). This guarantee is limited to the cost of repairing the product. To the extent permitted by law, the Manufacturer does not accept and will not be held liable for any financial loss incurred in connection with the failure of any product to operate in accordance with the expected standards.
- Page 45 If you are resident in the Republic of Ireland, this guarantee will be governed by Irish law and the Irish courts will have jurisdiction. This guarantee is provided by Beko plc. Beko House, 1 Greenhill Crescent, Watford, Hertfordshire. WD18 8QU.
- Page 46 90 days of the original purchase date. You can register by first visiting Beko.co.uk/register and by following the online instructions. Beko Free standing appliances come with a 12 month parts and labour guarantee as standard, Beko Built-in appliances come with a 12 month parts and labour guarantee as standard.
- Page 47 Further details are available at http://www.beko.co.uk/cookie-and- privacy. 13. These Terms and Conditions are governed by the laws of England and Wales; manufacturer: Beko plc, Beko House, 1 Greenhill Crescent, Watford WD18 8QU. Company Registration Number: 02415578. HOW TO OBTAIN SERVICE FOR YOUR APPLIANCE Please keep your purchase receipt or other proof of purchase details in a safe place;...
- Page 48 Send us a secure message through our online contact us form. Please visit our website, click Contact Us and choose a product support topic from the list of options. Complete the required details and click send message. Product registrations For UK registrations please visit beko.co.uk/register and for the Republic of Ireland visit beko.ie/register. 48/EN...