Advertisement
Interface Description/ 接口说明
7
NOTE/ 说明
The color identifier of the alarm cable is subject to the actual pigtail label.
告警线缆颜色标识以实际的尾线标签为准。
NO.
Item
Description
序号
名称
说明
Indicates the network interface that supports power over Ethernet (PoE). When the power input
1
LAN/POE
interface and PoE interface are connected at the same time, PoE is preferred.
网络接口。支持PoE供电。当电源输入接口和PoE同时连接时，优先PoE供电。
ALARM_OUT Indicates the alarm output interface. ALARM_OUT and ALARM_REF form a group of alarm
output.
ALARM_REF
告警输出接口。ALARM_OUT和ALARM_REF组成一组告警输出。
ALARM_IN
Indicates the alarm input interface. ALARM_IN and GND form a group of alarm input.
2
告警输入接口。ALARM_IN和GND组成一组告警输入。
GND
Indicates the RS485 interface that enables the camera and the connected device to send data to
RS485+
each other in half-duplex mode through the transparent channel.
RS485-
RS485接口。通过该接口，摄像机可以以半双工的方式通过透明通道与连接的设备互相传递数据。
Analog video output interface. The interface supports only D1 video output.
3
VIDEO
模拟视频输出接口。该接口仅支持以D1分辨率输出视频。
AUDIO OUT Indicates the video input/output interface. To ensure audio output quality, connect a 3.5 mm
4
TRS connector to the interface.
5
AUDIO IN
音频输入输出接口。为保证音频输出质量，请使用三段式3.5mm音频接头。
Indicates the power input interface. This interface supports 12 V DC (9.0 V to 15.0 V) and 24 V
AC24V/
6
AC (18.0 V to 29.9 V) power input.
DC12V
电源输入接口。支持DC 12V（9.0V～15.0V）和AC 24V（18.0V～29.9V）电源输入。
Indicates the ground interface of an IPC.
7
GND
设备接地接口。
Prepare for Installation Tools/ 准备安装工具
PVC insulation tape
绝缘胶带
Hammer drill (for mounting a
Marker
camera on the ceiling or wall)
记号笔
冲击钻（吊顶和墙壁安装时使用）
Phillips screwdriver (Head model: 0#,
2#; screwdriver bit length > 75 mm)
十字螺丝刀（刀头型号为：0#、2#，批
头长度大于75mm）
1
2
3
4
5
6
Wiring terminal
Measuring tape
接线端子
钢卷尺
Claw hammer (for mounting a camera
on the ceiling or wall)
羊角锤（吊顶和墙壁安装时使用）
Cable stripper
RJ-45 connector crimping tool
剥线钳
水晶头压线钳
Reset button and SD card slot/Reset 键和 SD 卡槽
1
NO.
Operation
Description
序号
操作
说明
SD card slot that supports only Micro SD cards of Class 6 or higher classes. You can replace a Micro
SD card only when the device is powered off. When a Micro SD card is used for the first time, log in
1
to the web page of the device and format the Micro SD card. For details, see Configuration Guide.
Use a Phillips
SD卡卡槽，仅支持Micro SD卡（Class 6及以上）。请在设备断电的情况下插拔SD卡，否则会造成系统异
screwdriver to
常。首次使用时，请登录设备Web客户端，格式化SD卡，操作方法请参见《配置指南》。
uninstall the
Reset button. To restart the device, hold down the RST button for less than 3s. To restore the device
transparent
to factory defaults, hold down the RST button for at least 3s during the device running or hold down
cover. You can
2
the RST button, power on the device, and keep holding down the RST button for more than 5s.
find the reset
重置按钮。运行时按住RST键短于3秒重启设备；运行时按住RST键不短于3秒或者按住RST键后上电并持续按
button, SD card
住RST键不短于5秒后恢复出厂配置。
slot, focus screw
Auxiliary focus button and indicator. After you adjust the zoom bolt to obtain the desired image
rod, and zoom
quality, press the auxiliary focus button. Then the auxiliary focus indicator blinks, for example, you
screw rod.
can hear beeps if the IPC is connected to an audio output cable. Adjust the focus bolt. When the
3
使用十字螺丝刀
image focus is clear, the auxiliary focus indicator is steady on and you can hear a long beep.
将透明罩卸下，
辅助对焦按钮及辅助对焦指示灯。调整变焦螺杆获取所需画面后，再按下辅助对焦按钮，辅助对焦指示灯闪烁
即可看到重置键、
（如接音频输出，可听到"滴滴"声）。调整聚焦螺杆，当画面聚焦清晰后，指示灯长亮（音频长响）。
SD 卡槽、聚焦螺
Zoom screw rod. You can loosen it to adjust the angle of view and tighten it after the adjutment.
杆和变焦螺杆。
4
变焦螺杆（T~W）。拧松调整画面视场角，调整结束后拧紧螺杆。
Focus screw rod. You can loosen it to adjust the image resolution and tighten it after the adjustment.
5
聚焦螺杆。拧松螺杆调整画面清晰度，调整结束后拧紧螺杆。
Security Precautions/ 安全注意事项
Carefully read and strictly comply with the following instructions and pay attention to the alarm information in this manual:
请仔细阅读本说明并严格遵守，留意本手册中的所有警告信息。
• The power adapter to be used by the device must meet the input voltage and current requirements described on the device label.
设备所使用的电源适配器必须满足设备标签上注明的电源输入电压和输入电流要求。
• Install a lightning arrester and effectively ground the device shell.
请安装避雷器，设备外壳必须有效接地。
• Risk of explosion if battery is replaced by an incorrect type dispose of used batteries according to the instructions.
如果更换不正确的电池规格会有爆炸的风险，请按制造商说明书处理使用过的电池。
• This is a class A product. In a domestic environment this product may cause radio in ference in which case the user may be
required to take adequate measures.
此为 A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对其干扰采取切实可行的措施。
• Use a soft and dry cloth when cleaning the camera body. Do not use strong and abrasive alkaline cleaner or volatile solvent such
as alcohol, benzene, or thinner.
清洁机身可用柔软的干布擦拭，请勿使用如酒精、苯或稀释剂等挥发性溶剂或者强烈的、带有研磨性的碱性清洁剂。
• Keep the device away from water or any other liquids. Take proper water-proof measures when installing the device outdoors.
禁止让任何液体流入设备中，如果安装在户外，必须做好防水措施。
• Keep the device away from heat sources, fire sources (such as heating apparatus or candles), and strong magnetic fields (for
example, high-voltage power distribution cabinet).
安放设备时请远离热源、裸露的火源（例如电暖器、蜡烛等）和强磁场环境（例如高压变电箱）。
• Avoid any unauthorized modifications on the design of the structure, security, or performance.
未经授权，任何单位和个人不得对设备进行结构、安全和性能方面的改动。
• Installation and maintenance must be performed by professional technical engineers or system installation engineers.
有关本装置的所有安装维修工作均应由专业的维修技术人员或系统安装人员来完成。
• Use product-attached auxiliaries and recommended fittings.
请使用产品配套的附件以及厂商推荐的配件。
• Carry a device by the device body. Do not pull the pigtails.
搬运设备时，使用双手合抱机身将摄像机捧起，禁止提拉尾线。
• Comply with related laws and regulations, and respect legal rights of others when using this device. Post a reminder "You have
entered the electronic surveillance area" at the most visible location if cameras are installed at public places.
使用本设备时应遵循相关的法律法规， 尊重他人的合法权利。 如果您在公共场所安装摄像机， 请在醒目的位置给予提示：您已进入电子监控范围。
5
4
2
3
Advertisement
