Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pasmo S930-Turbo
Summary of Contents for Pasmo S930-Turbo
- Page 1 Ｉ ｎ ｓ ｔ ｒｕ ｃ ｔｉ ｏ ｎ ｓ PASMO Food Technology Co., Ltd ■ Thank you for choosing the PASMO series soft ice cream equipment. ■ This manual will give you a detailed description of the operation and maintenance of the...
-
Page 2: Table Of Contents
Contents ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 1 Safety precautions Equipment installation ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ ‥ 2 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 3 ～ Equipment parts ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 5 Introduction for control panel ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 6 Display screen content explanation ‥‥‥‥‥‥‥‥‥‥‥ ‥‥‥‥ 7 Adjusting method of the hardness value 8 ～ ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ Washing parts ‥‥‥‥‥‥‥‥... -
Page 3: Safety Precautions
Safety precautions Equipment installation ◆ Please read and understand the safety precautions carefully before use. Warning ◆ Please comply with the safety-related contents described below. ◆ The meaning of the logo is stated as follows. Please entrust the professionals for the Please install it on a horizontal and firm ground. -
Page 4: Equipment Parts
Equipment parts Equipment parts （Gravity model） （Air pump model） Hopper cover Hopper cover Air tube Air pump Agitator blade Agitator blade Piston reset ring Piston reset ring Side piston Side piston Clip scraper Clip scraper Piston Piston Handle Handle O-ring Discharge door O-ring Discharge door... -
Page 5: Introduction For Control Panel
Display screen content explanation Introduction for the control panel Display screen For detailed digital explanation, ＋ Hopper 【 】 ＋ Wash button Cylinder Wednesday please refer to page 6 Short press this button, the Don not serve Time Digital displays (status display) main motor works only, which is only for cleaning. -
Page 6: Adjusting Method Of The Hardness Value
Adjusting method of the Washing parts （* Applicable to gravity model） hardness value Hoper cover Agitator blade Piston Each raw material has an optimum hardness value ＋ Hopper corresponding to itself. It is recommended to set ＋ Cylinder Wednesday the hardness value to 100. The hardness value Piston Don not serve Time... -
Page 7: Brush Usage Recommendation
Brush usage Washing parts （* Applicable to air pump model） recommendation （* Applicable to gravity model） Please use the brush attached to the kit for parts washing. Small brush Hoper cover Agitator blade Piston Medium brush Piston o-ring Big brush Beater shaft Beater Discharge door... -
Page 8: Recommendations For Wearing Parts Replacement
Brush usage Recommendations for recommendation wearing parts replacement （* Applicable to air pump model） Please use the brush attached to the kit for parts washing. The invisible scratches on the gasket ring may cause the problem of "ice cream leakage". Small brush ●... -
Page 9: Suggestion For Purchasing The Accessory Products
Assembly method of key parts Suggestion for purchasing the accessory products Assembly of beater 。 Please install the clip scraper and beater shaft on the beater according to the method below. ● Height is 153cm, large ice cream lamp model Clip scraper Height is 136cm, medium ice cream lamp model ●... - Page 10 Hole position Assembly for the air tube Please check the O-ring carefully at the bottom of Reset ring the air tube. The outer air tube hole where the protruding part of the inner air tube located is Piston Discharge Door Installation Outer air tube o-ring the hole currently used.
-
Page 11: Ice Cream Making Process
* Note: It is forbidden to make the air pump If the raw material contains particles such as non-meltable fibers, work if there is no raw material in the hopper, please contact with PASMO. if not so, it will cause the gear to wear out. Air pump screw... - Page 12 Before pouring the material, make sure that the storage hopper does not have any water remaining. If the raw material contains particles such as non-meltable fibers, please contact with PASMO. Installation of equipment accessorie Turn off the power supply. ●...
- Page 13 Daily operation process Washing process （* Applicable to air pump model） Ratio of food-grade disinfectant powder for machine washing and 含氯消毒粉 disinfection. 9.5L water The ratio is 1:9.5L (1 bag of sanitizer and 9.5L water). Washing of equipment accessory Sterilize and wash three times a week. ●...
- Page 14 Please discharge the remaining disinfectant water in the equipment by using the drainage box. Note: Make sure the air pump is completely disassembled and cleaned (Applicable to the air pump model) Fix the contraction band of the drainage box onthe top two nuts of the discharge door. ●...