Advertisement
Table of Contents
- 1 Table of Contents
- 2 Pasmo Warm Reminder
- 3 Introduction of Pasmo Machine
- 4 Introduction of Control Panel
- 5 Introduction of Spare Parts
- 6 Introduction of Cleaning and Installation of the Machine
- 7 Airpump Installation
- 8 Making Ice Cream
- 9 Operation of Precooling
- 10 Problems and Solutions
- 11 Fault Code and Solutions
- 12 Matching Products
- Download this manual
Advertisement
Table of Contents
Related Manuals for Pasmo S318
Summary of Contents for Pasmo S318
- Page 1 PASMO ICE CREAM MACHINE OPERATION MANUAL PASMO AMERICA...
-
Page 2: Table Of Contents
PASMO PART PASMO PASMO OPERATI O N MANUAL ontents PASMO WARM REMINDER..................02-03 INTRODUCTION OF PASMO MACHINE..............04-05 INTRODUCTION OF CONTROL PANEL..............INTRODUCTION OF SPARE PARTS................ 07-08 INTRODUCTION OF CLEANING AND INSTALLATION OF THE MACHINE..09-10 AIRPUMP INSTALLATION..................MAKING ICE CREAM.................... -
Page 3: Pasmo Warm Reminder
PASMO PART PASMO PASMO OPERATI O N MANUAL PASMO WARM REMINDER： PLEASE OPERATE THE MACHINE CORRECTLY After receiving the machines from logistics company, the machines need to be placed steady for 4 hours to make sure the compressors work normally. - Page 4 (Figure 3) (Figure 4) If you purchase Pasmo soft ice cream machine with water cool, pls correctly install tube according to manufacturer's guidance. No need space for radiating, 2 tubes for input water and 1 tube for out of water.
-
Page 5: Introduction Of Pasmo Machine
PASMO PART PASMO PASMO OPERATI O N MANUAL PASMO INTRODUCTION OF PASMO MACHINE： INTRODUCTION OF PASMO MACHINE odel S520F (Example)： Hopper Control board Handle On-off switch Discharge door Drip-tray Radiating ＰＡＳＭＯ ＯＰＥＲＡＴＩＯＮ... - Page 6 PASMO INTRODUCTION OF PASMO MACHINE: PLEASE OPERATE THE MACHINE CORRECTLY S110F S230F S930F S520F S970F ＰＡＳＭＯ ＯＰＥＲＡＴＩＯＮ...
-
Page 7: Introduction Of Control Panel
PASMO PART PASMO PASMO OPERATI O N MANUAL PASMO INTRODUCTION OF CONTROL PANEL: PLEASE OPERATE THE MACHINE CORRECTLY A: MIX LOW: If MIX LOW LED flash, it means mix in hopper lower than sensor. B: READY：If READY flash,it means ice cream is ready,can dispense ice cream. - Page 8 PASMO PART PASMO PASMO OPERATI O N MANUAL INTRODUCTION OF WORN PARTS AND CONSUMABLES： PLEASE OPERATE THE MACHINE CORRECTLY Lubricant Clip scraper Disinfectant powder Piston H O-ring Piston O-ring Discharge door O-ring NOTE: 1.Please do not clean machine with hot water more than 40 Celsius.
-
Page 9: Introduction Of Spare Parts
PASMO INTRODUCTION OF SPARE PARTS： PLEASE OPERATE THE MACHINE CORRECTLY ·Fixed pin ·Discharge door ·Clip scraper ·Beater ·Handle ·Piston O-ring ·Discharge door O-ring ·Piston H O-ring ·Air tube ·Hopper cover ·Lock nut ·Middle Piston ·Beater shaft ·Air pump ·Piston ＰＡＳＭＯ ＯＰＥＲＡＴＩＯＮ... -
Page 10: Introduction Of Cleaning And Installation Of The Machine
PASMO PART PASMO PASMO OPERATI O N MANUAL INTRODUCTION OF CLEANING AND INSTALLATION OF THE MACHINE： PLEASE OPERATE THE MACHINE CORRECTLY Add disinfectant powder to 9.5L normal temperature water and mix them. Cleaning spare parts with 5L disinfectant water. After cleaning,install clip... - Page 11 Install discharge door correctly Install nuts,ensure discharge door installed correctly Install handles to piston,add fixed pin and agitator. Add the left 4.5L disinfectant water to hopper. Press “WASH”to start washing machine for 1 minute. Press “STOP” to stop wash, dispense the water by pressing handle.
-
Page 12: Airpump Installation
PASMO PART PASMO PASMO OPERATI O N MANUAL PASMO AIRPUMP INSTALLATION： PLEASE OPERATE THE MACHINE CORRECTLY ccess of ① A motor of air pump - you can take out from machines. The air pump will not work if incorrect installed. -
Page 13: Making Ice Cream
PASMO PART PASMO PASMO OPERATI O N MANUAL PASMO MAKING ICE CREAM： PLEASE OPERATE THE MACHINE CORRECTLY MACHINE WITHOUT AIRPUMP: For thin ice cream ingredients： (1)Add ingredients to hopper and cylinder, meanwhile press handle to dispense the water out. By this, we... - Page 14 MACHINE WITH AIRPUMP: For thin ice cream ingredients： This （1）Add ingredients to hopper and cylinder, meanwhile press handle to dispense the water out. will leftover dispense the water in machine. s are coming (2) Add until no bubble from hole, install feed tube, do not connect with air pump. ress WASH, check if the flow from air pump, stop the WASH after confirmation.
- Page 15 to intake mix NOTE: you can adjust the time for air pump , press OFF for 5 seconds, until you get "UD", after the screen show P1,then short press OFF to switch the set time is 15 seconds, you can adjust through UP or DOWN, the more thick of ingredients, the more time for pump to work, we recommend to more than 20 seconds.
-
Page 16: Operation Of Precooling
PASMO PART PASMO PASMO OPERATI O N MANUAL PASMO OPERATION OF PRECOOLING： PLEASE OPERATE THE MACHINE CORRECTLY Blue button is for Standby function, pre-cooling for both hopper and cylinder. Precooling for both hopper and cylinder： ⑴ After close of business, press STOP, take out and clean the air pump, take out and clean agitator and feed tube and install again, then press“standby”. -
Page 17: Problems And Solutions
PASMO PART PASMO PASMO OPERATI O N MANUAL PASMO PROBLEMS AND SOLUTIONS： PLEASE OPERATE THE MACHINE CORRECTLY 1. Refrigerating fluid leakage 3. Condenser is dirty BAD COOLING: 4. Circumstance temperature is too high. 5. The space for radiating is not enough... -
Page 18: Fault Code And Solutions
PASMO PART PASMO PASMO OPERATI O N MANUAL PASMO FAULT CODE AND SOLUTIONS: PLEASE OPERATE THE MACHINE CORRECTLY Error Code Solution Check the voltage, It is set to 243 and if the voltage goes avove, High voltage error machine goes into fault state to protect itself. Call Reseller. -
Page 19: Matching Products
PASMO MATCHING PRODUCTS: Ice Cream Light Material:abs Specification: 1550mm tall Diameter Of 530mm Power: 4w Voltage: 220v Product Use: The Publicity And Selling Of Ice Cream Machine Feature: Twelve Color Lights Can Be Chose Three Light Transform Mode MAGIC COLOR CHANGING® SPOON... - Page 20 TAIZHOU PASMO FOOD TECHNOLOGY CO.,LTD A SINO-AUS-THAI JOINT VENTURE TEL:+86(576)84088555 PASMO AMERICA 844-52-PASMO www.pasmousa.com US Sales/Showroom 23961 Craftsman Road Ste E/F Calabasas, CA 91302 Chi n a Sal e s Headquarter: 18th Fl o or, Zongshanghui Bui l d i n g, Huangyan Area, Tai z hou Ci t y, Zhej i a ng Provi n ce, Chi n a Chi n a Producti o n Base:No.69, Dej i a n Road, Ji a ngkou Food Industri a l Zone,...