Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for jcm-tech ML8NF
Summary of Contents for jcm-tech ML8NF
- Page 1 User's Manual ML8NF RSENS...
-
Page 2: Table Of Contents
Table of contents Maintenance Maintenance 3 3 3 3 Maintenance Maintenance Important safety instructions for installation Important safety instructions for use Use of the equipment Technical Technical Data Data Technical Technical Data Data Connection Connection Connection Connection Installation Installation Installation Installation Installation with support Installation without support... -
Page 3: Maintenance
Maintenance Important safety instructions for installation Disconnect the power supply whenever you proceed to the installation or repair of the control panel. The panel must be installed while the power is disconnected. • Before installing the panel, remove all unnecessary ropes or chains and disable any equipment such as •... -
Page 4: Important Safety Instructions For Use
Important safety instructions for use Do not allow children to play with the door controls. • Keep the remote controls out of the reach of children. • Watch the door movement and keep people away until the door is fully open or closed. •... -
Page 5: Technical Technical Data Technical Data
Technical Data Parameter Value Frequency 868,35 MHz Codification High security rolling code 27 codes (expandable to 500 codes with memory Memory card) Power supply 230Vac ±10% Maximum motor power 750W / 1200W (intensive use / residential use) Standby / operating consumption 23mA / 43mA Motor fuses Optional cards... -
Page 6: Connection
Connection Motor connections: U=OPEN (Brown) V=CLOSE (Black) W(c)=COMMON (Blue) jcmtechnologies... -
Page 7: Installation
Installation Installation with support UNSCREW EXTRACT SUPPORT DRILL WALL HANG CONTROL PANEL SCREW Installation without support UNSCREW OPEN TOP DRILL WALL Door Positioning AFTER FEW SECONDS DOOR OPENED PRESS & HOLD CLOSE DOOR CLOSED DOOR CLOSES jcmtechnologies... -
Page 8: Programming
Programming Radio Manual Programming (Remote controls, wireless buttons, etc) PRESS RED RPROG PUSHBUTTON OPEN TOP LED TURNS ON PRESS TRANSMITTER PRESS RPROG PUSHBUTTON LED TURNS OFF NOTE: To program transmitters onto different channels, press and hold the red RADIO PROG pushbutton until the LED for that channel turns on, then release the RADIO PROG pushbutton and press the transmitter. -
Page 9: Safety Safety Devices Safety Devices Programming Devices Programming
Safety devices programming RadioSens3 Transmitter Programming in RSEC3 Receiver PRESS PROG BUTTON OF THE PLUGABLE CARD PRESS PROG ONE BEEP AND RSEC3 TRANSMITTER PROGRAMMED LED TURNS ON LED TURNS OFF AND END SLIDE THE COVER TO PROG CLOSE PRESS RPROG BUTTON Adjust the sensitivity and inhibition point In order to adapt the operation of the system to the irregular conditions of the floor, the equipment can be inhibited for the last 4cm at the end of the travel of the door. -
Page 10: Maneuver Maneuver Programming Maneuver Programming
Maneuver programming Programming the door maneuver with RadioSens3 system PRESS WHITE PROG PRESS START PUSHBUTTON PUSHBUTTON DOOR CLOSED LED TURNS ON DOOR OPENS 2 SECONDS DOOR CLOSES DOOR STOPS AUTO DOOR OPENS AUTO PRESS START PUSHBUTTON DOOR STOPS AUTO AUTOCLOSE TIME DOOR CLOSES DOOR CLOSES AUTO *INHIBITION ZONE:... -
Page 11: Eu Declaration Of Conformity
J J J J C C C C M M M M T T T T e e e e c c c c h h h h n n n n o o o o l l l l o o o o g g g g i i i i e e e e s s s s hereby declares that the product M M M M 8 8 8 8 N N N N F F F F complies with the relevant fundamental requirements of the RED Directive 2014/53/EU, as well as with the Machine Directive 2006/42/EC whenever its usage is foreseen; and with the 2011/65/EU RoHS Directive. See website www.jcm-tech.com/declarations/ JCM TECHNOLOGIES, SA C/COSTA D'EN PARATGE, 6B 08500 VIC (BARCELONA)