Page 1
Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
Page 2
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking by Wells Manufacturing for its products are based upon the equipment manufactured by Wells Manufacturing is limitations in this warranty. Seller’s obligation under this warranted against defects in materials and workmanship for a...
PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Manufacturing appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
Drop-in warmers (i.e. SS206T) are equipped with wellsloks, WELLSLOKS uniquely designed turnout tabs which help secure the warmer top flange to the countertop. Bottom-mounted warmers (i.e. SS206ET) require that the cutout be flanged to provide a mounting means. IL2469 See the Installation Instructions, supplied with the particular appliance, for details.
Do not operate this appliance if the control panel is damaged. Call installation instructions are your Authorized Wells Service Agent for service. read and followed. Damage to the appliance may result if The technical content of this manual, including any wiring diagrams,...
Page 6
Wells Manufacturing does not recommend installing bottom- mount SS206ET(D) warmers in a plastic counter.
Page 7
INSTALLATION 4. For “top-mounted” warmers (i.e. warmers mounted from above the counter top): Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout. After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter Apply a thin bead of food-grade silicone sealant around the flange to seal it to the counter.
CAUTION: SHOCK HAZARD Wells Manufacturing recommends operating WET for consistent food heating. If your wet-operation warmer is allowed to run dry, turn it OFF and DO NOT splash or pour water allow to cool to room temperature before adding water.
Never use metal implements, wire brushes, abrasive scratch pads or steel wool to clean stainless steel. Warmer pans, insets and other vessels are subject to a harsher environment. Wells Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer pans.
Contact your Authorized Wells Service Agency to inspect warmer if water or grease contamination is suspected. Close drain valve. Add proper amount of warm water. Turn control...
Page 11
CLEANING INSTRUCTIONS CAUTION: WEEKLY CLEANING INSTRUCTIONS CHEMICAL BURN PREPARATIONS: Remove any insets, pans and/or adapter tops. HAZARD Drain or remove water from well if used for wet Deilimng chemicals may be operation. caustic. Wear appropriate personal protective equipment. FREQUENCY: Weekly, or whenever lime or scale is seen Follow cleaner manufacturer’s accumulating on the sides of the warmer pans.
One or more pans of an auto-fill unit Blocked drain manifold Clean drain manifold do not fill There are no user-serviceable components in this appliance. In all instances of damage or malfunction, contact your Authorized Wells Service Agency for repairs.
Page 22
PARTS & SERVICE DESCRIPTION PART NO. Always use an inset. DO NOT place food directly into the warmer pan. ADAPTERS & INSETS ADAPTER TOP, convert SS206 to hold two 7 qt. insets WS-20176 ADAPTER TOP, convert SS206 to hold two 4 qt. insets and two 2½ qt. insets WS-20434 ADAPTER TOP, convert SMPT, HW/SMP or 1 side of TMPT to hold...
Page 23
WELLSLOK EXTENSION KIT, for UL LISTED authorized replacement parts, circular warmers only, adapt to wood counter up to 1¾” thick contact your Wells authorized WS-22592* service agency, or call: WELLSLOK EXTENSION KIT, for UL LISTED 12”...
Page 24
WELLS MANUFACTURING 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.com...