Edimax EN-9250TX-E Quick Installation Manual
  1. Manuals
  2. Brands
  3. Edimax Manuals
  4. PCI Card
  5. EN-9250TX-E
  6. Quick installation manual

Edimax EN-9250TX-E Quick Installation Manual

Ethernet gigabit pci express adapter
Hide thumbs Also See for EN-9250TX-E:
Table of Contents

Advertisement

Quick Links

Download this manual
E
t
h
E
t
h
P
C
I
E
P
C
I
E
Quick Installation Guide
e
r
n
e
t
G
i
g
e
r
n
e
t
G
i
x
p
r
e
s
s
A
x
p
r
e
s
s
A
Version: 1.0
(January, 2007)
a
b
i
t
g
a
b
i
t
d
a
p
t
e
r
d
a
p
t
e
r

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EN-9250TX-E and is the answer not in the manual?

Questions and answers

Related Manuals for Edimax EN-9250TX-E

Summary of Contents for Edimax EN-9250TX-E

  • Page 1 Quick Installation Guide Version: 1.0 (January, 2007)
  • Page 3 Č ý Č é Č ý Č é ř ž é ř ž ñ ñ ç ç ó ó ę ł ą ę ł ą ê í ê í Р у с с к и й Н а й д и...

  • Page 4: Package List

    Introduction PCI Express is the next generation of I/O interconnection standards to support the high bandwidth required by PCs, consumer electronics and communication devices. The architecture is a cost-effective, low-pin count, and point-to-point technology to maximize the bandwidth, reduce the costs and design complexity and enable smaller form factors. This card is the best solution for Gigabit Ethernet PCI Express with potential transfer rates of 2.5 Gbps using a single-lane (or x1) PCI Express link.
  • Page 6 3. Remove the metal bracket on the rear of a free PCI Express slot. 4. Insert the card into one free PCI Express slot and screw it firmly on the bracket side. 5. Place the cover back onto the computer. 6.

  • Page 7: Driver Installation

    Driver Installation 1. Windows 2000/XP/2003 Driver Installation Once the Windows 2000, XP and 2003 startup, the system will detect the Gigabit Ethernet PCI Express Adapter. Follow the procedures to install Gigabit Ethernet PCI Express Adapter driver under Microsoft Windows XP server pack 2 Operation System 1.
  • Page 8 3. The following screen will be displayed. Click “Setup Utility ”. 4. The following screen will be displayed. Please select the driver based on your Windows XP/2000/2003 Operation System.
  • Page 9 The “Gigabit PCI Express Adapter Utilities - InstallShield Wizard” is displayed auto run. 5. Please Click “ Next “...
  • Page 10 6. Please select “ I accept the terms in the license agreement “ and click “ Next “ 7. Please click “ Install “ to install the Gigabit PCI Express adapter utility.
  • Page 11 8. The system starts installing the Gigabit PCI Express adapter utility. 9. Click "Finish" to complete Gigabit Ethernet PCI Express Adapter installation.

  • Page 12: Hardware Check

    Hardware Check Go to “Device Manager” which you can access from the Control Panel. You should see an "Generic Marvell Yukon Chipset based Gigabit Ethernet Controller" under "Network Adapter" item. Start > Control Panel > System > Hardware > Device Manager...

  • Page 13: Networking Settings

    Networking Settings Click "Network Connection" in Control Panel to set your network settings. 2. Right-click the Local Area Connection of Gigabit Ethernet card, then select "Properties" from menu. 3. Double-click the "Internet Protocol (TCP/IP)" item to set network settings.
  • Page 14 4. Right-click the Local Area Connection of the Gigabit Ethernet card, then select "Status" from the menu to check the network status.
  • Page 15 Vista Driver Installation Once the Windows Vista startup, the system will detect the Gigabit Ethernet PCI Express Adapter. Follow the procedures to install Gigabit Ethernet PCI Express Adapter driver under Microsoft Windows XP server pack 2 Operation System 10. Please click "Cancel" to close it, when Found New Hardware Wizard Windows pop-up. 11.
  • Page 16 12. The following screen will be displayed. Click “Setup Utility ”. 13. The following screen will be displayed. Please select the driver based on your Windows Vista Operation System.
  • Page 17 The “Gigabit PCI Express Adapter Utilities - InstallShield Wizard” is displayed auto run. 14. Please Click “ Next “...
  • Page 18 15. Please select “ I accept the terms in the license agreement “ and click “ Next “ 16. Please click “ Install “ to install the Gigabit PCI Express adapter utility.
  • Page 19 17. The system starts installing the Gigabit PCI Express adapter utility. 18. Click "Finish" to complete Gigabit Ethernet PCI Express Adapter installation.
  • Page 20 Hardware Check Go to “Device Manager” which you can access from the Control Panel. You should see an "Generic Marvell Yukon Chipset based Gigabit Ethernet Controller" under "Network Adapter" item. Start > Control Panel > System > Hardware > Device Manager Networking Settings Click "Network Sharing Center "...
  • Page 21 2. Click "Manage network connections " ito set your network settings. 3. Double-click the "Internet Protocol (TCP/IP)" item to set network settings.

  • Page 22: Troubleshooting

    Troubleshooting The computer cannot detect the Gigabit Ethernet PCI Express Adapter 1. Make sure that the PCI Express cards is correctly plugged into the PCI Express slot; if not, turn off the computer and plug it in again 2. If the PCI Express card is plugged in correctly, see if the golden connectors on the card are clean;...

Table of Contents