Related Manuals for Areca ARC-1883 Series
Summary of Contents for Areca ARC-1883 Series
- Page 1 SAS RAID Expander-CLI ARC-1883ix-12/16/24 (12Gb/s SAS RAID Controller) USER Guide Version: 1.2 Issue Date: April, 2018...
- Page 2 Copyright and Trademarks The information regarding products in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. All brands and trademarks are the properties of their respective owners.
-
Page 3: Table Of Contents
Contents 1. Introduction ..............4 1.1 Expander RS-232C Port Pin Assignment .......5 1.2 Start-up VT100 Screen ............5 2. CLI Command .............. 9 • HELP Command ..............9 • PASS Command ..............9 • LO Command ..............10 • LINK Command ............... 10 •... -
Page 4: Introduction
1. Introduction This Command Line Interface (CLI) is provided for you to configure the Areca SAS RAID controller expander functions. The CLI is useful in environments where a graphical user interface (GUI) is not available. • Locations of RS-232 Port ARC-1883ix-16 •... -
Page 5: Expander Rs-232C Port Pin Assignment
SAS RAID Expander-CLI 1.1 Expander RS-232C Port Pin Assignment To ensure proper communications between the SAS RAID controller expander and the VT-100 Terminal Emulation, Please configure the VT100 terminal emulation settings to the values shown below: Terminal requirement Connection Null-modem cable Baud Rate 115,200 Data bits... - Page 6 SAS RAID Expander-CLI Step 2. Open “HYPERTRM.EXE”. Step 3. Enter a name you prefer and then click “OK”.
- Page 7 SAS RAID Expander-CLI Step 4. Select an appropriate connecting port and then click "OK". Step 5. Configure the port parameter settings and then click “OK”. Bits per second: 115200 Data bits: 8 Parity: None Stop bits: 1 Flow control: None Step 6.
- Page 8 SAS RAID Expander-CLI Step 7. Configure the "Connect To" setting. Step 8. Configure the "Settings" items and then click "OK". Function, arrow and ctrl keys act as: Terminal Keys Backspace key sends: Crtl+H Emulation: VT100 Telnet terminal: VT100 Back scroll buffer lines: 500 Now, The VT100 is ready to be used.
-
Page 9: Cli Command
SAS RAID Expander-CLI 2. CLI Command • HELP Command This command provides an on-line table of contents, providing brief descriptions of the help sub-commands. You can use the <CLI> help to get detail information about the CLI commands summary. Syntax CLI>help[Enter] Example: CLI>help... -
Page 10: Lo Command
SAS RAID Expander-CLI Example: CLI>pass Old Password:**** New Password:**** Verify New Password:**** Password Changed But Not Save Permanently! Note, use CLI command “st” to keep permanently. • LO Command To exit the selected expander box CLI shell, use the lo command. Syntax CLI>... - Page 11 SAS RAID Expander-CLI Example: CLI>link c0 6g 3g ;;;;; set cable0 link speed range [6G(10), 3G(9)] CLI>st CLI> Reboot to take effect. 2. Set all slots with same link speed rate Syntax CLI>link [Index(D)| 255] High-Rate(D) Low-Rate(D) Index: Slot Index High-Rate(D), Low-Rate(D): [11|10|9] or [12g|6g|3g] PS.
- Page 12 SAS RAID Expander-CLI NAME TYPE ADDRESS SLOT 01 SATA 5001B469-189AE00D SLOT 02 SAS 5011B469-189AE00C SLOT 03 SATA 5011B469-189AE00E SLOT 04 SATA 5011B469-189AE00F SLOT 05 SATA 5011B469-189AE009 SLOT 06 6G 12G SATA 5011B469-189AE008 SLOT 07 SATA 5011B469-189AE00A SLOT 08 SATA 5011B469-189AE00B SLOT 09 SATA 5011B469-189AE005 SLOT 10...
-
Page 13: Edfb Command (Same As "Dhpm")
SAS RAID Expander-CLI SLOT 09 SATA 5011B469-189AE005 SLOT 10 SATA 5011B469-189AE004 SLOT 11 SAS 500000E0-168F8E92 SLOT 12 SAS 500000E0-168F8E99 NOTE: 1. If DHPM is enabled, it will keep NLR=12G. • EDFB Command (Same as “DHPM”) From FW 1.26 version, EDFB default only supports for SATA drive (from Chip vendor suggestion). - Page 14 SAS RAID Expander-CLI SLOT 05 SATA 5011B469-189AE009 SLOT 06 SATA 5011B469-189AE008 SLOT 07 SATA 5011B469-189AE00A SLOT 08 SATA 5011B469-189AE00B SLOT 09 SATA 5011B469-189AE005 SLOT 10 SATA 5011B469-189AE004 SLOT 11 SATA 500000E0-168F8E92 SLOT 12 SATA 500000E0-168F8E99 CLI>edfb sata 2,12 ;;;;; set drive slot 2,12 on CLI>st Reset or PowerCycle CLI>link...
-
Page 15: Sys Command
Syntax CLI>sys [Enter] Example: CLI>sys ======================================== Hardware Revision Information:- ======================================== Vendor ID : Areca Technology Co Ltd. Taiwan, R.O.C Model ID : ARC-8028 Serial No. : 0000000000000000 Unit Serial No. Expander SAS Address : 0x5001B469189AE03F Product Revision... -
Page 16: Spin Command
SAS RAID Expander-CLI ======================================== Firmware Revision Information:- ======================================== Boot Image: Revision: 100.BD.00.0A 12/05/13 Firmware Family: 0 OemFamily: 0 Fast Boot: Yes Image Address: 0x10000000 Firmware Copy 1: Revision: 100.BD.01.0A 01/06/14 Firmware Family: 0 OemFamily: 0 Fast Boot: Yes Image Address: 0x10100000 Firmware Copy 2: [Active] Revision: 100.BD.01.0A 01/06/14 Firmware Family: 0 OemFamily: 0... -
Page 17: St Command
SAS RAID Expander-CLI Current SpinUp Attribute: Drive Number: 1 Delay: 1024 ms CLI>spin 512 3 New SpinUp Attribute: Drive Number: 3 Delay: 512 ms Current SpinUp Attribute: Drive Number: 1 Delay: 1024 ms • ST Command The st command stores system configurations in flash. Since all the revised parameter setting is temporarily stored in the working RAM, the ST command saves those parameters permanently in flash ROM. - Page 18 SAS RAID Expander-CLI ArrayDevice Element (0x17): ======================================== NAME TYPE ADDRESS SLOT 01 0 3.0G 5000C500-0D2002D1 SLOT 02 SLOT 03 SLOT 04 3 1.5G SATA 5001B469-84965C03 SLOT 05 SLOT 06 SLOT 07 6 6.0G 5000C500-17C8FD25 SLOT 08 SLOT 09 SLOT 10 SLOT 11 SLOT 12 Connector Element (0x19):...
-
Page 19: Showlogs Command
SAS RAID Expander-CLI Temperature Element (0x04): ======================================== NAME CT(‘C) OTWarn ENC. Temp Chip Temp Voltage Element (0x12): ======================================== NAME VOLT(V) OVLMT UVLMT STATUS 0.99 1.07 0.94 None 4.96 5.32 4.63 None PowerSupply Element (0x02): ======================================== NAME STATUS PowerSupply01 PowerSupply02 AudibleAlarm Element (0x06): ======================================== NAME STATUS... -
Page 20: Fdl Command
SAS RAID Expander-CLI • FDL Command The box has added the expander firmware update through the CLI on the external RS-232 port. Before you process the firmware update, there are two block regions that you can update expander microcode on SAS expander box. 1. -
Page 21: Counters Reset Command
SAS RAID Expander-CLI 8. If transfer OK, the transfered data is updated. Cold-start expander (Power cycle again) to take effect. Example: Update procedure, use Xmodem to transfer, refer to “fdl” com- mand for detail operation. CLI> fdl { code | mfgb } Use HyperTerminal or TeraTerm utility with Xmodem mode to transfer and update files. - Page 22 SAS RAID Expander-CLI == InvWrdCnt ==DispErrCnt ==LossSyncCnt ==RstSeqFailCnt= Phy 00 0x00000000 0x00000000 0x00000000 0x00000000 Phy 01 0x00000000 0x00000000 0x00000000 0x00000000 Phy 02 0x00000000 0x00000000 0x00000000 0x00000000 Phy 03 0x00000000 0x00000000 0x00000000 0x00000000 Phy 04 0x00000000 0x00000000 0x00000000 0x00000000 Phy 05 0x00000000 0x00000000 0x00000000 0x00000000 Phy 06 0x00000000 0x00000000...
-
Page 23: Sasaddr Command
SAS RAID Expander-CLI • Sasaddr Command CLI>sasaddr Expander New SAS Address: 0x5001B4690400083F Expander Current SAS Address: EXP Port SAS Address: 0x5001B4690400083F SXP Port SAS Address: 0x5001B4690400083D STP Port SAS Address: Disabled • Sub Command The subtractive command allows you to set the subtractive ports on expander.