Related Manuals for Hafco Metalmaster BS-321AS
Summary of Contents for Hafco Metalmaster BS-321AS
- Page 1 Instruction Manual for BS-321AS (B034A) 31/03/2016 INSTRUCTION MANUAL BS-321AS Semi - Automatic Swivel Head-Dual Mitre Metal Cutting Band Saw (415V) 510 x 260mm (W x H) Rectangle B034A...
- Page 2 Instruction Manual for BS-321AS (B034A) 31/03/2016 General Machinery Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Read the entire Manual before starting 14. Use correct amperage extension cords. machinery. Machinery may cause serious injury if Undersized extension cords overheat and lose not correctly used.
- Page 3 Instruction Manual for BS-321AS (B034A) 31/03/2016 Metal Cutting Bandsaw Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Maintenance. 8. Understand the machines controls. Make sure the bandsaw is turned Make sure you off and disconnect from the main power supply understand the use and operation of all controls.
- Page 4 Instruction Manual for BS-321AS (B034A) 31/03/2016...
-
Page 5: Table Of Contents
Instruction Manual for BS-321AS (B034A) 31/03/2016 TABLE OF CONTENTS ACCIDENT PREVENTION AND SAFETY REGULATION ..............1 1.1 Advice for the operator......................... 1 1.2 The electrical equipment according to European Standard" CENELEC EN 60204-1"......1 1.3 Warning labels ............................. 1 1.4 Emergencies according to European Standard “CENELEC EN 60204-1” .......... 1 MACHINE TRANSPORTATION AND INSTALLATION............... -
Page 6: Accident Prevention And Safety Regulation
Instruction Manual for BS-321AS (B034A) 31/03/2016 - In the event of a power cut, the specific start-up ACCIDENT PREVENTION AND button must be reset. SAFETY REGULATION - The machine has been tested in conformity with This machine has been designed to comply with... -
Page 7: Machine Transportation And Installation
Instruction Manual for BS-321AS (B034A) 31/03/2016 Minimum requirements for housing the MACHINE TRANSPORTATION AND machine INSTALLATION - Main voltage and frequency must comply with the machine’s motor requirements. Machine dimensions - Environment temperature should fall within (-10ºC to + 50 ºC). -
Page 8: Install The Outlet Tray, Length Stop Device And Mobile Coolant Trays
Instruction Manual for BS-321AS (B034A) 31/03/2016 Install the outlet tray, length stop device rear of the machine to the wall. Position the and mobile coolant trays. anchors using screws and expansion plugs or tie rods sunk in cement. Install the outlet tray and stop bar on to the... -
Page 9: Description Of Machine Parts
Instruction Manual for BS-321AS (B034A) 31/03/2016 The vise system DESCRIPTION OF MACHINE PARTS Control panel A hydraulic vise is used for clamping work material. Each of the vises has a miter slot, which is good for the right or left side’s angle cutting to 60°. -
Page 10: Chip Brush
Instruction Manual for BS-321AS (B034A) 31/03/2016 This machine is equipped with automatic power The speed change dial adjusts the variable speed shut-off safety device to prevent any further transmission in blade speed. Change only while damage when a blade has been broken. There is blade is moving. -
Page 11: Thrust Roller Adjustment
Instruction Manual for BS-321AS (B034A) 31/03/2016 - When ready to cut the work piece, the carbide Blade tracking adjustment guide must be adjusted by adjusting the screws to properly compressed blade. The tungsten Caution carbide blades should touch, but not pinch the blade. -
Page 12: Hydraulic Vise Pressure (Optional)
Instruction Manual for BS-321AS (B034A) 31/03/2016 - Switch to manual mode, use the blade running switch 3.1 E to check the proper ride of the blade. Hydraulic vise pressure (optional) The hydraulic vise pressure can be monitored and adjusted by a pressure gauge on the base of the machine. -
Page 13: Using The Vise
Instruction Manual for BS-321AS (B034A) 31/03/2016 Using the vise - Disconnect the machine from power supply. - Open the belt cover. Remove 4 screws from the top. Remove 1 screw from the front. Remove 8 screws from the cover. - Turn the dial counter-clockwise to open the pulley discs and loosen the belt. -
Page 14: Laser Guide Device (Optional)
Instruction Manual for BS-321AS (B034A) 31/03/2016 - Turn the power off and recheck the blade - Open the vise more than 250mm. tension and chip brush. If further adjustment is - Attach and Tighten posts bolts’ (A) on to vises. -
Page 15: Stopping Or Emergency Stopping
Instruction Manual for BS-321AS (B034A) 31/03/2016 - Secure the material, use the vise close button - Use compressed air to clean the blade guides (I). (guide bearings and drain hole of the lubricating - Base on the diameter of the material; set the cooling). -
Page 16: Technical Characteristics
Instruction Manual for BS-321AS (B034A) 31/03/2016 - Replace the screw (S) after oil completely flows off. - Filling in gear oil from T hole, until oil be sight from the visual glass. - Replace hole using the fill hole (T). -
Page 17: Control Circuit Diagram
Instruction Manual for BS-321AS (B034A) 31/03/2016... -
Page 18: Part List & Explosion Drawings
Instruction Manual for BS-321AS (B034A) 31/03/2016 SECTION A - PARTS LIST Part No. Description Size / Stock No. Q'ty Part No. Description Size / Stock No. Q'ty Hex. Cap Bolt M8x20L Big Round Head Screw M6x8L Coolant Tray 331D3-02 Bracket Cover 331D3-36 Hex. - Page 19 Instruction Manual for BS-321AS (B034A) 31/03/2016...
- Page 20 Instruction Manual for BS-321AS (B034A) 31/03/2016 SECTION B - PARTS LIST Part No. Description Size / Stock No. Q'ty Part No. Description Size / Stock No. Q'ty Lower Cover 331D3-26-A Hex. Socket Cap Screw M8x20L Button Head Socket Screw M5x8L Hex.
- Page 21 Instruction Manual for BS-321AS (B034A) 31/03/2016 SECTION B - PARTS LIST Part No. Description Size / Stock No. Q'ty Part No. Description Size / Stock No. Q'ty Shaft 331D2-53-D Bush 331D2-53-C C Ring Shaft 331D2-53 B100 Vise Locking Collar 331D2-53-A B101 Hex.
- Page 22 Instruction Manual for BS-321AS (B034A) 31/03/2016...
- Page 23 Instruction Manual for BS-321AS (B034A) 31/03/2016 SECTION C - PARTS LIST Part No. Description Size / Stock No. Q'ty Part No. Description Size / Stock No. Q'ty Hex. Socket Cap Screw M6x16L Contact Plate 331D2-48 Spring Washer Tension Gauge Spacer...
- Page 24 Instruction Manual for BS-321AS (B034A) 31/03/2016 SECTION C - PARTS LIST Part No. Description Size / Stock No. Q'ty Part No. Description Size / Stock No. Q'ty Button Head Socket Screw M5x8L C142 Bearing 6000 331D5-10A Motor C143 Adjusting Carbide (No Grooved) 331D2-09-A...
- Page 25 Instruction Manual for BS-321AS (B034A) 31/03/2016...
- Page 26 Instruction Manual for BS-321AS (B034A) 31/03/2016 SECTION D - PARTS LIST Part No. Description Size / Stock No. Q'ty Part No. Description Size / Stock No. Q'ty Power Switch Operation Mode Switch Coolant Overload Relay Coolant Contactor Hydraulic Motor Overload Relay...
- Page 27 Instruction Manual for BS-321AS (B034A) 31/03/2016...
Need help?
Do you have a question about the BS-321AS and is the answer not in the manual?
Questions and answers