Advertisement
Thank you for purchasing our 8x4 GardenSaver Shed with Sliding Door - Metal Roof.
Please take the time to identify all the parts prior to assembly.
Parts List:
A. Floor Section
1 - 45 ½" x 75" - Large Floor Frame (2 Joists unattached)
1 - 45 ½" x 21" - Small Floor Frame (2 Joists ATTACHED)
2 - 1 ½" x 3 ½" x 71 7/8" - Floor Joists
(Steps 1 - 3)
2 - 1 ½" x 3 ½" x 45 ½" - Floor Runners Short
3 - 1 ½" x 3 ½" x 47 ¾" - Floor Runners Long
(Steps 4 - 5)
1 - 5/8" x 45 ½" x 75" - Plywood Flooring
1 - 5/8" x 45 ½" x 21" - Plywood Flooring
(Steps 6 - 8)
B. Wall Section
5 - 1 ½" x 2 ½" x 45 ½" - Wall Plates
4 - 45 ½" x 75" - Wall Panels
1 - 45 ½" x 73" - Front Wall Panel
(Steps 9 - 17)
1 - 2" x 3 ⅜" x 68 1/4" - Door Header - Long (Dado on edge)
1 - 2" x 3 ⅜" x 22 3/4" - Door Header - Short (Dado on edge)
1 - 1 ½" x 3 ⅜" x 73" - Door Jamb - Vertical
(Steps 18 - 19)
2 - Top Triangular Siding Pc for Angle Wall Extendors (L/R)
2 - 4
" - Angle Wall Extendors (L/R)
5 ¼
2 - 9" x 45 ½" - Wall Extendors
2 - 1 ½" x 2 ½" x 42 3/8"- Extendor Wall Cleats
(Steps 20 - 27)
1 - ¾" x 3 ½" x 70" - Horizontal Wall Cleat
1 - ¾" x 3 ½" x 21" - Horizontal Wall Cleat
(
Step 28)
C. Rafter & Roof Section
6 - 1 ½" x 2 ½" x 54" - Rafters
2 - ½" x 3 ½" x 48" - Front Soffits
2 - ½" x 3 ½" x 48" - Rear Soffits
(Steps 31 - 36)
6 - 3/4" x 3 1/2" x 50" - Roof Battens
4 - 3/4" x 1 1/2" x 21 1/2" - Batten Spacers
(Steps 37 - 40)
2 - Rafter/Facia Nailing Strips - ¾" x ¾" x 51"
(Step 41)
3 - Metal Roof Panels - 39" w x 58 1/2" d
(Steps 42 - 48)
Foam Enclosures - Several Strips
(Step 47)
Toll Free 1-888-658-1658
D. Miscellaneous Section
(Skirting, Trim, Door, Facia & Misc. Parts
4 - ½" x 4 ½" x 45
2 - ½" x 4" x 45 1/4") - Front Bottom Skirting
(Steps 49 - 51)
6 - ¾" x 2 ½" x 36" - Corner Filler Trims
2 - ¾" x 2 ½" x 36" - Corner Filler Trims - Front Left
2 - ¾" x 2 ½" x 10" - Front Top Corner Filler Trims
(Steps 18 & 29 & 52)
2 - ½" x 5 ½" x 79" - Rear Corner Trims
2 - ½" x 5 ½" x 88 ¾" - Front Corner Trims
2 - ½" x 2 ½" x 80" - Side Rear Corner Trims
1 - ½" x 2 ½" x 79" - Rear Middle Trim
2 - ½" x 2 ½" x 88 ¾" - Side Front Corner Trims
(Steps 53 - 56)
Sliding Door Parts
1 - 49" x 74"
1 - 71" long - Aluminum Door Track with Hanging Brackets
1 - 1 1/2" x 2 1/2" x 80 3/4" - Lower Door Track
1 - 3/4" x 4" x 87 3/4" - Lower Door Track Cover
2 - 1 1/2" x 3" x 3 1/2" - Lower Door Track Stops
1 - 1 ½" x 3 ½" x 87 3/4" - Top Track Overlay
1 - 3/4" x 5 ½" x 87 3/4" - Top Track Overlay - Front
2 - ½" x 4 1/4" x 43 7/8" - (Bevel Siding) - Track Overlay Sill
1 - 1 ½" x 2 ½" x 66 7/8" - Door Stop
(Steps 57 - 66)
2 - ½" x 4" x 54 1/8" - Side Facia (Angle Cut Ends) - reverse
4 - ½" x 4" x 50 ½" - Front and Rear Facia
(Steps 67 - 69)
2 - 6" x 60" angled - Front Metal Drip Caps
(Step 70)
1 - ½" x 2 ½" x 6 1/4" - Front Middle Trim
(Step 71)
1 - Detail Facia Plate (4" high)
(Step 72)
1 - 18" x 22 ½" - Window Insert
1 - 24 1/16" angle cut / 3 -23" straight cut - Window Trim Pkg
(Step 73 - 74)
1 - 45 ¼" - Extra Piece of Bevel Wall Siding - Use if wall panel
siding is damaged or to shim floor or door.
Note: All Trim, Facia and Bottom Skirting pieces will
be positioned rough face out when installed.
www.outdoorlivingtoday.com
Page 4
" - Bottom Skirting (Finger Jointed)
¼
Sliding Door
-
sales@outdoorlivingtoday.com
)
(Step 18)
Advertisement
