Specifications And Safety; General Safety Information - Flotec FPSC5000A Owner's Manual

Specifications and Safety

Description
This Submersible Sump Pump is designed for home sumps.
The permanent split capacitor motor is oil filled, sealed for cooler
running, and has automatic-reset
thermal protection. Ball bearings on the motor shaft never need
lubrication. The power cord is a 3-wire, grounding-type cord.
specifications
Power supply ................................115V, 60 HZ., 15 Amp Circuit
Liquid Temp. Range ................................ 32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ...................... 15 Amps
Discharge: .......................................................1-1/2" Female NPT
This pump is designed for use in a residential sump only.
Pump water only with this pump.
notice: This unit is not designed as a waterfall or fountain
pump, or for applications involving salt water or brine! Use with
waterfalls, fountains, salt water or brine will void warranty.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
notice: read this owner's Manual for installation,
operation, and safety information.

General safety inforMation

Your automatic sump pump should give years of trouble-
free service when correctly installed, maintained, and used.
However, interruption of power to the pump, dirt/debris
in the sump, flooding that exceeds the pump's capacity,
electrical or mechanical failure in the pump, etc., may
prevent normal pump operation. To help prevent damage
from flooding, purchase a secondary AC sump pump, a
DC backup sump pump, and/or a high water alarm. See
the "Troubleshooting Chart" in this manual for information
about common sump pump problems and remedies. For
more information,call Flotec customer
service at 1-800-365-6832.
Hazardous voltage. to reduce the risk of
hazardous or fatal electrical shock, follow
instructions a through D, below:
a. this pump has an approved 3-conductor power
cord with 3-prong, grounding-type plug. connect
the pump only to a properly grounded, 3-prong
outlet. if the sump pump circuit has a 2-prong
outlet, replace it with a grounded 3-prong outlet
installed according to code.
B. Unplug the pump before handling or servicing it.
if your basement floor is wet, turn off all power
before walking on it. if the shut-off box is in the
basement, call your electric company or hydro
authority to shut off service to the house, or
call your local fire department for instructions.
After turning off the power, remove the pump
for
service.
For parts or assistance, call Flotec Customer Service at
c. protect the electrical cords from sharp objects,
hot surfaces, oil, and chemicals. avoid kinking
the cords. replace damaged or worn cords.
D. Do not lift the pump by the power cord.
plastic pipe glue is extremely
flammable. Follow the glue manufacturer's instructions when
assembling glued plastic pipe.
Burn hazard. Modern motors may run hot.
Allow 20 minutes to cool before handling.
1. Know the pump application, limitations, and potential
hazards.
2. Do not use this pump in water with fish present. if
any oil leaks out of the motor it can kill fish.
3. Drain the system completely before servicing it.
4. To prevent a flexible discharge line from whipping,
which could cause injury or damage, fasten it down
before starting the pump.
5. Before each use, check any hoses in the system for
weakness or wear. Make certain that all connections are
tight.
6. Periodically inspect the sump, the pump, and the piping
for debris and foreign objects. Perform routine cleaning
as required.
7. Personal Safety:
a. Wear safety glasses at all times when working with
pumps.
b. Keep your work area clean, uncluttered and properly
lighted; put away all unused tools and equipment.
c. Keep visitors at a safe distance from the work area.
d. Make workshop child-proof with padlocks and
master switches. Remove any starter keys.
8. This pump installation must meet all applicable laws,
codes, and ordinances.
tools required:
Pipe wrench, Strap Wrench, or Slip-Joint Pliers,
Hacksaw,
Screw Driver,
File or Sandpaper
Materials required:
1-1/2" ABS or PVC Pipe with Cement to match
Threaded Adapter (Pipe to Pump)
Check Valve – Purchase a check valve that goes in the discharge
line or in the pump discharge. If your check valve does not have
a 1/8" anti-airlock hole, drill one in the discharge pipe just below
the check valve. Anti-airlock hole must aim away from switch.
Be sure to install the check valve so that the flow will be away
from the pump.
1-800-365-6832
2