Acer Aspire X3470 Service Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Desktop
  5. Aspire X3470
  6. Service manual

Acer Aspire X3470 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Acer
Aspire X3470
Service Guide
PRINTED IN TAIWAN

Advertisement

Table of Contents
loading

Related Manuals for Acer Aspire X3470

Summary of Contents for Acer Aspire X3470

  • Page 1 Acer Aspire X3470 Service Guide PRINTED IN TAIWAN...

  • Page 2: Revision History

    Revision History Please refer to the table below for the updates made on this service guide. Date Chapter Updates...
  • Page 3 Copyright Copyright © 2011 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without...
  • Page 4 Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
  • Page 5 Conventions The following conventions are used in this manual: SCREEN MESSAGES NOTE WARNING CAUTION IMPORTANT Denotes actual messages that appear on screen. Gives additional information related to the current topic. Alerts you to any physical risk or system damage that might result from doing or not doing specific actions.

  • Page 6: Fru Information

    Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

  • Page 7: Table Of Contents

    Table of Contents System Tour Features Block Diagram System Components Front Panel Rear Panel Hardware Specifications and Configurations Power Management Function(ACPI support function) System Utilities CMOS Setup Utility Entering CMOS setup Navigating Through the Setup Utility Setup Utility Menus Main System Disassembly and Assembly Disassembly Requirements Pre-disassembly Procedure...
  • Page 8 System Check Procedures Power System Check System External Inspection System Internal Inspection Beep Codes Checkpoints BIOS Recovery Jumper and Connector Information M/B Placement Jumper Setting Setting Jumper FRU (Field Replaceable Unit) List Aspire X3470 Exploded Diagram Aspire X3470 FRU List viii...

  • Page 9: System Tour

    HD Graphics Support • Dual independent display -- HDMI and VGA. • Digital displayHDMI with HDMI CTS 1.4 compliance. • Need to measure VGA follow Acer VGA SOP. • Support for Cool'n'Quiet™ via FID/VID change. • Support for AMD PowerNow!™. •...

  • Page 10: Hard Disk Drive

    Monitor compatible is requested to the monitor AVL and DQM recommended list. • Must with latch in slot. • Hard disk drive Support up to three SATA ports • 3.5",25.4mm • Capacity and models are listed on AVLC • Optical disk drive Support one SATA 5.25"...

  • Page 11: System Bios

    2 * H1X2 GPIO header • 1 * 3pin IR receiver header to super I/O • System BIOS • AMI Kernel with Acer skin/copyright • Power supply Non PFC 250W / PFC 250W /FR 300W. • Support models are listed on AVLC.

  • Page 12: Block Diagram

    Block Diagram Chapter 1...

  • Page 13: System Components

    System Components This section is a virtual tour of the system’s interior and exterior components. Front Panel Chapter 1 Component HDD activity indicator USB 2.0 ports Microphone-in jack Headphone/Speaker-out/line-out jack CF I/II (CompactFlash Type I/II) slot XD(XD-Picture)/SD(Secure Digital)/PRO slot Optical drive eject button Optical drive Power button...

  • Page 14: Rear Panel

    Rear Panel Component Line-in jack USB 3.0 ports RJ45 LAN connector PS2 mouse port Power connector PS2 keyboard port HDMI port D-sub port USB 2.0 ports Line-out jack Microphone jack Expansion slot(graphics card and Wireless card) Chapter 1...

  • Page 15: Hardware Specifications And Configurations

    LAN controller AMD A75+Realtek RTL8111E SATA controller AMD A75 Super IO ITE 8772F controller Chapter 1 Specification AMI Kernel with Acer skin P01-A2 SPI Flash SMBIOS(DMI)2.7 1st priority: Hard Disk 2nd priority: CD/DVT 3rd priority: Removable Device 4th priority: LAN Description Press while the system is booting to enter BIOS Setup Utility.

  • Page 16: Memory Combinations

    Memory Combinations Slot Memory Slot 1 1GB,2GB,4GB Slot 2 1GB,2GB,4GB Maximum System Memory Supported System Memory Item Memory slot number Support Memory size per socket Support memory type Support memory interface Support memory voltage Support memory module package Support to parity check feature Support to error correction code (ECC) feature No Memory module combinations SATA Interface...

  • Page 17: Audio Interface

    Audio Interface Item Audio controller Audio controller type Audio channel Audio function control Mono or stereo Compatibility Music synthesizer Sampling rate Microphone/Headphone jack Chapter 1 Specification Intel High Definition audio controller ALC662 2.1 channel Enable/disable by BIOS Setup Stereo Meets the latest Microsoft Windows Logo Program audio specification WaveRT based audio function driver and logo ready for Windows 7 and Vista EAX™...

  • Page 18: Environmental Requirements

    Environmental Requirements Item Specification Temperature Operating +5°C ~ +35°C Non-operating -20 ~ +60°C (Storage package) Humidity Operating 15% to 80% RH Non-operating 10% to 90% RH Vibration Operating (unpacked) 5 ~ 500 Hz: 2.20g RMS random, 10 minutes per axis in all 3 axes. 5 ~500 Hz: 1.09g RMS random, 1 hour per axis in all 3 axes.

  • Page 19: Power Management Function(Acpi Support Function)

    Power Management Function(ACPI support function) Device Standby Mode Independent power management timer for hard disk drive devices(0-15 minutes,time step=1minute). • Hard Disk drive goes into Standby mode(for ATA standard interface). • Disable V-sync to control the VESA DPMS monitor. • Resume method:device activated (keyboard for DOS, keyboard &mouse for Windows.

  • Page 20: System Utilities

    System Utilities CMOS Setup Utility CMOS setup is a hardware configuration program built into the system ROM, called the complementary metal- oxide semiconductor (CMOS) Setup Utility. Since most systems are already properly configured and optimized, there is no need to run this utility. You will need to run this utility under the following conditions. When changing the system configuration settings •...

  • Page 21: Entering Cmos Setup

    Entering CMOS setup Turn on the server and the monitor. If the server is already turned on, close all open applications, then restart the server. During POST, press Delete. If you fail to press Delete before POST is completed, you will need to restart the server. The Setup Main menu will be displayed showing the Setup’s menu bar.

  • Page 22: Setup Utility Menus

    Setup Utility Menus Main The Setup Main menu includes the following main setup categories. Parameter Description System BIOS Version Version number of the BIOS setup utility. Build Date Date when the BIOS setup utility was built Processor Type of CPU installed on the system. Core Frequency Core speed of the CPU installed on the system.
  • Page 23 Advanced Parameter Miscellaneous Advanced Chipset Configuration Integrated Peripherals PC Health Status Description Press Enter to access the Miscellaneous submenu Press Enter to access the Advanced Chipset Configuration submenu Press Enter to access the Integrated Peripherals submenu Press Enter to access the PC Health Status submenu Chapter 2...
  • Page 24 Miscellaneous Parameter Description AHCI Port0/1/2 Displays the status of auto detection of the AHCI device. Clock to All DIMM/ This item allows you to enable or disable the Clock to all DIMM/PCIE. PCIE Spread Spectrum Enables or disables the reduction of the mainboard’s EMI. Note: Remember to disable the Spread Spectrum feature if you are overclocking.

  • Page 25: Advanced Chipset Configuration

    Advanced Chipset Configuration AMD Turbo Core This item allows you to enable or disable the AMD Turbo Core. AMD Cool’n’Quiet This item allows you to enable/disable your system utilize the AMD specific ACPI states to save power consumption. AMD-V This item allows you to enable or disable the AMD virtualization. Enabled Disabled Enabled...

  • Page 26: Integrated Peripherals

    Integrated Peripherals Parameter Description Onboard SATA Controller Enables or disables the onboard SATA controller. Onboard SATA Mode Select an operating mode for the onboard SATA. Onboard USB Controller Enables or disables the onboard USB controller. Legacy USB Support Enables or disables support for legacy USB devices. USB Storage Emulation If Auto, USB device equal or less than 2GB will be emulated as Floppy and remaining as harddrive.

  • Page 27: Pc Health Status

    PC Health Status Parameter Description Smart Fan Enables or disables the smart system fan control function. Option Enabled Disabled Chapter 2...
  • Page 28 Power Parameter Description ACPI Suspend Mode Select an ACPI state. Deep Power Off Mode Select the Deep power off Mode Power On by RTC Alarm Enables or Disables to wake up the system by RTC Alarm Function Power On by PCIE Devices This system can be turned off with a software commend.
  • Page 29 Security Parameter Description Supervisor Password This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. User Password This item allows you to change user password. Change Supervisor You can select this option and press <Enter>...

  • Page 30: Boot Options

    Boot Options 1st/2nd/3rd/4th/5th Boot Specifies the boot order from the available devices. Device EFI Device Priority Press Enter to access the EFI Device Priority submenu and specify the boot device priority sequence from available EFI devices. Hard Disk Drive Priority Press Enter to access the Hard Disk Drive Priority submenu and specify the boot device priority sequence from available hard drives.
  • Page 31 Exit Parameter Description Save & Exit Setup When you have completed the system configuration changes, select this option to leave the BIOS Setup Utility and reboot the computer, so the new system configuration parameters can take effect. Select Discard Changes and Exit Select this option to quit the BIOS Setup Utility without making any permanent changes to the Setup system configuration, and reboot the computer.

  • Page 32: System Disassembly And Assembly

    System Disassembly and Assembly This chapter contains step-by-step procedures on how to disassemble and assembly the desktop computer for maintenance and troubleshooting. Disassembly Requirements To disassemble the computer, you need the following tools: Wrist grounding strap and conductive mat for preventing electrostatic discharge •...

  • Page 33: Pre-Disassembly Procedure

    Pre-disassembly Procedure Before proceeding with the disassembly procedure, perform the steps listed below: Turn off the system and all the peripherals connected to it. Unplug the power cord from the power outlets. Unplug the power cord from the system. Unplug all peripheral cables from the system. Place the system unit on a flat, stable surface.

  • Page 34: Removing The Side Panel

    Removing the Side Panel Remove the two screws located on the rear edge of the side panel. Slide the side panel toward the back of the chassis until the tabs on the cover disengage with the slots on the chassis. Lift the side panel away from the server and put it aside for reinstallation later.

  • Page 35: Removing The Heat Sink Fan Assembly

    Removing the Heat Sink Fan Assembly WARNING:The heat sink becomes very hot when the system is on. NEVER touch the heat sink with any metal or with your hands. Loosen the hook of heat sink as shown below. Push the pole of heat sink as below the arrowhead’s direction shows. Note :CPU Fan has been highlighted with the yellow rectangle as above image shows.Please detach the CPU Fan and follow local regulations for disposal.
  • Page 36 Lift the heat sink fan assembly away from the mainboard. Lay down the heat sink fan assembly, in an upright position, on top of the optical drive, as shown below, then disconnect the fan cable from the mainboard. Remove the heat sink fan assembly from the chassis then lay it down in an upright position—with the thermal patch facing upward.

  • Page 37: Removing The Processor

    Removing the Processor IMPORTANT:Before removing a processor from the mainboard, make sure to create a backup file of all important data. WARNING:The processor becomes very hot when the system is on. Allow it to cool off first before handling. Release the load lever. Lift the load lever to the fully open, upright position.
  • Page 38 Pull out the processor from the socket. IMPORTANT: If you are going to install a new processor, note the arrow on the corner to make sure the processor is properly oriented over the socket. Chapter 3...

  • Page 39: Removing The Wireless Lan Card

    Removing the Wireless LAN Card Remove the screws that secures the card to the chassis. Gently pull the card to remove it from the mainboard. Note: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal.

  • Page 40: Removing The Vga Card

    Removing the VGA Card Remove the screws that secures the card to the chassis. Gently pull the card to remove it from the mainboard. Note: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal.

  • Page 41: Removing The Front Bezel

    Removing the Front Bezel Release the front bezel from the chassis interior. Pull the bezel away from the chassis. NOTE: The bezel can’t be entirely removed until completed below step.due to the other end of power cable connecting with motherboard. Chapter 3...

  • Page 42: Removing The Cage Of Odd And Hdd

    Removing the Cage of ODD and HDD Disconnect the data and power cables from the rear of the optical drive. Remove the two screws from chassis. Lift the cage up and turn it over. Chapter 3...
  • Page 43 Use the hands to hold the cage assembly, and lay down the cage assembly on the chassis, as shown below, then disconnect the data and power cables from the rear of the Hard disk drive. Disconnect the other end of the HDD/ODD data cable from the mainboard. Release the HDD data cables away from Chassis clip.
  • Page 44 Disconnect the power switch cable from the motherboard. Pull the power switch cable from the chassis, then remove the bezel. Chapter 3...

  • Page 45: Removing The Hard Disk Drive

    Removing the Hard Disk Drive Remove the four screws that secure the HDD module to the HDD bracket. Slide the HDD out of the bracket. Chapter 3...

  • Page 46: Removing The Optical Drive

    Removing the Optical Drive Remove the screw from the bracket. Pull the drive out of the drive bay. Chapter 3...

  • Page 47: Removing The Memory Modules

    Removing the Memory Modules IMPORTANT:Before removing any DIMM from the memory board, make sure to create a backup file of all important data. Press the holding clips on both sides of the DIMM slot outward to release the DIMM(1). Gently pull the DIMM upward to pull it away from the M/B(2). Note: Circuit boards >10 cm²...

  • Page 48: Removing The Power Supply

    Removing the Power Supply Disconnect the 4-pin and 24-pin power supply cables from the mainboard. Remove the screw that secures the power supply to the chassis. Chapter 3...
  • Page 49 Remove the three screws that secure the power supply to the rear panel. Lift the power supply module out of the chassis. Chapter 3...

  • Page 50: Removing The Mainboard

    Removing the Mainboard Disconnect the front USB cable and front audio cable from the mainboard. Release the cable from retention clip,then take out the retention clip. Release these cables away from Chassis clip. Chapter 3...
  • Page 51 Remove the four screws that secure the mainboard to the chassis. Note: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. Lift the board from the chassis. Chapter 3...
  • Page 52 Punching in IO Shield then you can remove it. Remove the RTC battery. Note:RTC battery has been highlighted with the yellow circle as above image shows.Please detach the RTC battery and follow local regulations for disposal. Chapter 3...

  • Page 53: Removing The Front I/O&Usb And Card Reader Boards

    Removing the Front I/O&USB and Card Reader Boards Removing the screw from chassis. Pull the front I/O and USB assembly from chassis. Remove the card reader board. Remove the two screws that secure the card reader board to the bracket. Chapter 3...
  • Page 54 Pull the card reader board out of the bracket. Note: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. Remove the front I/O&USB board. Remove the two screws that secure the I/O&USB board to the bracket.

  • Page 55: Assembly Requirements

    Assembly Requirements To assemble the computer, you need the following tools: Wrist grounding strap and conductive mat for preventing electrostatic discharge • Flat-blade screwdriver • Philips screwdriver • Hex screwdriver • Plastic flat-blade screwdriver • Plastic tweezers • NOTE: The screws for the different components vary in size. During the assembly process, group the screws with the corresponding components to avoid mismatch when putting back the components.

  • Page 56: Assembly Procedure

    Assembly Procedure Before proceeding with the assembly procedure, perform the steps listed below: Turn off the system and all the peripherals connected to it. Unplug the power cord from the power outlets. Unplug the power cord from the system. Unplug all peripheral cables from the system. Place the system unit on a flat, stable surface.

  • Page 57: Install The Processor

    Install the Processor Release the load lever and lift the load lever to the fully open. Put the CPU in the seat and close the load plate and load lever. NOTE: When you install the processor, note the arrow on the corner to make sure the processor is properly oriented over the socket.

  • Page 58: Install The Heat Sink Fan Assembly

    Install the Heat Sink Fan Assembly Put the CPU cooler on M/B retention module. Install the two taches of cooler to bracket. Chapter 3...
  • Page 59 Lock the CPU cooler. Connect the cooler cable to the main board. Chapter 3...

  • Page 60: Install The Memory

    Install the Memory Open the holding clips on both sides of the DIMM slot outward. Press down the memory. IMPORTANT:pls refer to below installing memory rule. Remark:A and B show different size of memory, size:A>B Chapter 3...

  • Page 61: Romoving The Side Panel

    Removing the Side Panel Remove the two screws located on the rear edge of the side panel. Slide the side panel toward the back of the chassis until the tabs on the cover disengage with the slots on the chassis. Lift the side panel away from the server and put it aside for reinstallation later.

  • Page 62: Romoving The Front Bezel

    Removing the Front Bezel Release the front bezel from the chassis interior. Pull the bezel away from the chassis. Chapter 3...

  • Page 63: Removing The Cage Of Odd And Hdd

    Removing the Cage of ODD and HDD Remove the two screws from chassis. Lift the cage up and turn it over. Punching in PCI Shelf slice then you can remove it. Chapter 3...

  • Page 64: Install The Power Supply

    Install the Power Supply Install the power supply to chassis. Fix the three screws. Fix another screw. Chapter 3...

  • Page 65: Install The I/O Shielding

    Install the I/O Shielding Install I/O shielding into chassis. Chapter 3...

  • Page 66: Install The Main Board

    Install the Main Board Put M/B in the chassis aligning the M/B I/O connector with I/O shielding. Fix1~ 6 pcs screws into the corresponding hole. NOTE: Make sure the I/O spring touching M/B after installing. Install the retention clip to chassis,then fix the front audio cable with the retention clip. Chapter 3...
  • Page 67 Take the bezel, shall front panel cable pass through chassis’s hole. as below blue rectangle image show Connect the front panel cable, front USB cable, and front audio cable to the mainboard. Connect the ATX 24Pin Power cable and ATX 4Pin Power cable to main board. Chapter 3...

  • Page 68: Install The Optical Drive

    Install the Optica Drive Push the drive to the drive bay. Fix the screw to the bracket. Chapter 3...

  • Page 69: Install The Hard Disk Drive

    Install the Hard Disk Drive Slide the HDD to the bracket. Fix the four screws to bracket. Chapter 3...

  • Page 70: Install The Cage Of Odd And Hdd

    Install the Cage of ODD and HDD Connect the other end of the HDD and ODD data cable to the mainboard. Let HDD SATA data cable pass through the two chassis clips. Use the hands to hold the cage assembly, and lay down the cage assembly on the chassis as shown below, then connect the data and power cables to the rear of the Hard disk drive.
  • Page 71 Install the cage to chassis. Fix the two screws to chassis. Connect the power cables and data cable to the rear of the optical drive. Chapter 3...

  • Page 72: Install The Front Bezel

    Install the Front Bezel Install the panel onto chassis and then check if it is Installed OK. Chapter 3...

  • Page 73: Install The Vga Card

    Install the VGA Card Press down the VGA card. Chapter 3...

  • Page 74: Install The Wireless Lan Card

    Install the Wireless LAN Card Press down the wireless lan card. Fix the two screws. Chapter 3...

  • Page 75: Install The Side Panel

    Install the Side Panel Install the side Panel, then fix two screws. Chapter 3...

  • Page 76: System Troubleshooting

    This chapter provides instructions on how to troubleshoot system hardware problems. Hardware Diagnostic Procedure IMPORTANT:The diagnostic tests described in this chapter are only intended to test Acer products. Non- Acerproducts, prototype cards, or modified options can give false errors and invalid systemresponses.

  • Page 77: System Check Procedures

    Verify that components are properly seated. Verify that all cable connectors inside the system are firmly and correctly attached to their appropriate connectors. Verify that all components are Acer-qualified and supported. 10. Replace the system covers. 11. Power on the system.

  • Page 78: Beep Codes

    Beep Codes Beep codes are used by the BIOS to indicate a serious or fatal error to the end user. Beep codes are used when an error occurs before the system video has been initialized. Beep codes will be generated by the system board speaker, commonly referred to as the PC speaker.

  • Page 79: Checkpoints

    Checkpoints A checkpoint is either a byte or word value output to I/O port 80h.The BIOS outputs checkpoints throughout bootblock and Power-On Self Test (POST) to indicate the task the system is currently executing. Checkpoint sare very useful in aiding software developers or technicians in debugging problems that occur during the pre- boot process.
  • Page 80 Checkpoint Restore CPUID value back into register. Give control to BIOS POST (ExecutePOSTKernel). See POST Code Checkpoints section of document for more information. System is waking from ACPI S3 state. E1-E8 EC- OEM memory detection/configuration error. This range is reserved for chipset vendors & system manufacturers.

  • Page 81: Bootblock Recovery Code Checkpoints

    Bootblock Recovery Code Checkpoints The Bootblock recovery code gets control when the BIOS determines that a BIOS recovery needs to occur because the user has forced the update or the BIOS checksum is corrupt. The following table describes the type of checkpoints that may occur during the Bootblock recovery portion of the BIOS. NOTE: Checkpoints may differ between different platforms based on system configuration.

  • Page 82: Bios Recovery

    BIOS Recovery AMIBIOS supports a "recovery flash" mode, which can be used to flash update a BIOS from the boot block. This is used to update a BIOS image without the need to boot to an operating system. The following is the process that user should follow to flash BIOS ROM.

  • Page 83: Jumper And Connector Information

    Jumper and Connector Information M/B Placement Label CPU socket 905Pin socket for AMD FM1 CPUs DIMM1~4 240-pin DDR3 SDRAM slots CN6801 Standard 24-pin ATX power connector Chapter 5 Description Label CPUFAN1 SYSFAN1 CN7802~3 Chapter 5 Description CPU cooling fan connector System fan connector GPIO function...
  • Page 84 Label CN7801 SATA0~2 CN6101~3 CN2901 J7502 J6201 J6101 J5101 CN4201 Description IR Receiver Header Serial ATA connectors Front panel USB headers Front panel audio header PCI Express x1 slot On board USB3.0 connector On board USB connector On board HDMI connector Auxiliary 4-pin power connector...

  • Page 85: Jumper Setting

    Jumper Setting The section explains how to set jumper for correct configuration of the mainboard. Setting Jumper Use the motherboard jumpers to set system configuration options. Jumpers with more numbered. When setting the jumpers, ensure that the jumper caps are Header Name 1.
  • Page 86 Header Name Function Definition 1 – TXP0 2 – GND 3 – TXN0 4 – TXP1 5 – GND 6 – TXN1 7 – TXP2 8 – GND 9 – TXN2 10 – TXP3 11 – GND 12 – TXN3 13 –...
  • Page 87 Header Name RJ45+USB Dual USB 3.0 Chapter 5 Function Definition 1 – CVT 2 – MDI0+ 3 – MDI0- 4 – MDI1+ 5 – MDI1- 6 – MDI2+ 7 – MDI2- 8 – MDI3+ 9 – MDI3- 10 – GND 11 –...
  • Page 88 Header Name Audio Front Audio Front USB 2.0 Function Definition 35 – LINEIN_L 32 – LINEIN_R 34 – LINEIN_JD 33 – AGND 25 – LINEOUT_L 22 – LINEOUT_R 24 – LINEOUT_JD 23 – AGND 5 – MIC_L 2 – MIC_R 4 –...
  • Page 89 Header Name Internal USB SATA 2. Power connector ATX PWR 4pin Chapter 5 Function Definition 1 – PWR 20 – NC 2 – USB3_RX3- 19 – PWR 3–USB3_RX3+ 18–USB3_RX4- 4 – GND 17–USB3_RX4+ 5–USB3_TX3- 16 – GND 6–USB3_TX3+ 15–USB3_TX4- 7 – GND 14–USB3_TX4+ 8 –...
  • Page 90 Header Name ATX PWR 24pin 3. Other on board pin header LED BTN Battery Holder IR receiver Function Definition 13 – 3.3V 1 – 3.3V 14 – -12V 2 – 3.3V 15 – GND 3 – GND 16 – ATX_ON 4 –...
  • Page 91 Header Name CLR CMOS CPUFAN SYSFAN Chapter 5 Function Definition 1 – RTCVCC 2 – VBAT 3 – GND 1 – GND 2 – 12V 3 – SENSE 4 – CTRL 1 – GND 2 – 12V 3 – SENSE 4 –...

  • Page 92: Fru (Field Replaceable Unit) List

    To scrap or to return the defective parts, follow the local government ordinance or regulations on • how to dispose it properly, or follow the rules set by your regional Acer office on how to return it. This document will be updated as more information about the FRU list becomes available.

  • Page 93: Aspire X3470 Exploded Diagram

    Aspire X3470 Exploded Diagram NOTE: This section will be updated when more information becomes available. Chapter 6...
  • Page 94 ITEM NAME Chassis-Bottom IO Sheilding Mother Board U-Chassis HDD-Bracket Side Plate ODD-Bracket-Link Top-Cover HDD-Lens Power-Switch Deco-Belt Spring-Button Power Button Acer Logo Chapter 6 Q’TY ITEM NAME Latch-ODD-Button ODD-Shielding ODD-Door ODD-Button F-IO Door F-IO Mylar Spring-IO-Door Front-Bezel Spring-ODD-Door1 Spring-ODD-Door2 F-IO ODD-Bracket...

  • Page 95: Aspire X3470 Fru List

    Aspire X3470 FRU List Category MB Kit MB Kit AX3470 AMD A75 Realtek8111E W/O 1394 Chassis Hon Hai Chassis xSFF HX097G w/ front USB4+1port for Aspire AX360 Bezel supports I/O shielding Bezel Hon Hai Aspire Bezel AX360 w/ USB 4+1port bezel w/HX097G chassis "CPU AMD A8 3850 4M Bx 2.9G, 100W, Quad...
  • Page 96 Category CPU AMD A4 3400 FM1 2.7G 1M 65W Bx Dual Core CPU AMD E2 3200 FM1 2.4G 1M 65W Bx Dual Core Memory GU502203EP0201 LF 128*8 0.065um ACR128X64D3U1333C9 LF 128*8 0.07um NT1GC64BH4B0PF-CG GU512303EP0202 LF 128*8 0.065um HU524303EP0200 NT2GC64B88B0NF-CG 256*8 50nm ACR256X64D3U1333C9 LF 128*8 0.07um ACR256X64D3U13C9G NT4GC64B8HB0NF-CG...
  • Page 97 Category ODD HLDS DVD-ROM HH DL 16X DH40N LF+HF Black Bezel (HF+Win7) SATA ODD PLDS DVD-ROM HH DL 16X DH-16D5SH LF+HF Black Bezel SATA w/Win7 ODD HLDS Super-Multi DRIVE HH 16X GH70N LF+HF Black Bezel SATA (Win7) ODD PLDS Super-Multi DRIVE HH DL 16X DH- 16ABSH LF Black Bezel (HF+Win7) SATA ODD PIONEER Super-Multi DRIVE HH DL 16X DVR-219RS LF Black Bezel SATA (Win7+HF)
  • Page 98 Category 89D685-321108 HD6450 1GB sDDR3 64bits DVI-I + HDMI SAMSUNG (LP) 288-1E180-C00AC HD6450 512MB SDDR3 64bits DVI-I + HDMI SAMSUNG G die (LP) 288-1E180-D00AC HD6450 512MB SDDR3 64bits DVI-I + HDMI Hynix DFR (LP) 89D685-321109 HD6450 512MB sDDR3 64bits DVI-I + HDMI SAMSUNG (LP) TV Tuner Card Avermedia H753-D TV Tuner Card PCIe Hybrid DVB-T, S/W Encoder, LP bracket...
  • Page 99 PFC 220W (8.5L) EuP FR 220W (8.5L) EuP 82+ External Speaker JS USB2.0 Speaker USB MS1238UA JS Speaker USB MS1238UA meet AJC spec Neosonica Speaker Acer logo /LF /0810 / 9M- 20A200-000 Neosonica USB Acer logo / 9M-20A200-000 meet AJC spec Remote control Philips Remote Controller RC2604307/01BG for EMEA ;pair with RV.11000.007...
  • Page 100 Category Keyboard LITE-ON SK-9621B USB 104KS Black Keyboard LITE-ON SK-9621B USB 104KS Black Traditional Chinese Keyboard LITE-ON SK-9621B USB 104KS Black Simplified Chinese Keyboard LITE-ON SK-9621B USB 104KS Black US International Keyboard LITE-ON SK-9621B USB 104KS Black Arabic/English Keyboard LITE-ON SK-9621B USB 104KS Black Thailand Keyboard LITE-ON SK-9621B USB 105KS Black Spanish...
  • Page 101 Category Keyboard LITE-ON SK-9621B USB 105KS Black Polish Keyboard LITE-ON SK-9621B USB 105KS Black Slovenian Keyboard LITE-ON SK-9621B USB 105KS Black Slovak Keyboard LITE-ON SK-9621B USB 104KS Black Russian Keyboard LITE-ON SK-9621B USB 105KS Black Hungarian Keyboard LITE-ON SK-9621B USB 104KS Black Greek Keyboard LITE-ON SK-9621B USB 105KS Black Danish...
  • Page 102 Category Keyboard PRIMAX KB36211 USB 104KS Black Simplified Chinese Keyboard PRIMAX KB36211 USB 104KS Black US International Keyboard PRIMAX KB36211 USB 104KS Black Arabic/English Keyboard PRIMAX KB36211 USB 104KS Black Thailand Keyboard PRIMAX KB36211 USB 105KS Black Spanish Keyboard PRIMAX KB36211 USB 105KS Black Portuguese Keyboard PRIMAX KB36211 USB 105KS Black Canadian French...
  • Page 103 Category Keyboard PRIMAX KB36211 USB 105KS Black Slovak Keyboard PRIMAX KB36211 USB 104KS Black Russian Keyboard PRIMAX KB36211 USB 105KS Black Hungarian Keyboard PRIMAX KB36211 USB 104KS Black Greek Keyboard PRIMAX KB36211 USB 105KS Black Danish Keyboard PRIMAX KB36211 USB 104KS Black Czech Keyboard PRIMAX KB36211 USB 105KS Black Romanian...
  • Page 104 Category Keyboard LITE-ON SK-9611 PS/2 104KS Black US International Keyboard LITE-ON SK-9611 PS/2 104KS Black Arabic/English Keyboard LITE-ON SK-9611 PS/2 104KS Black Thailand Keyboard LITE-ON SK-9611 PS/2 105KS Black Spanish Keyboard LITE-ON SK-9611 PS/2 105KS Black Portuguese Keyboard LITE-ON SK-9611 PS/2 105KS Black Canadian French Keyboard LITE-ON SK-9611 PS/2 107KS Black Brazilian Portuguese...
  • Page 105 Category Keyboard LITE-ON SK-9611 PS/2 104KS Black Russian Keyboard LITE-ON SK-9611 PS/2 105KS Black Hungarian Keyboard LITE-ON SK-9611 PS/2 104KS Black Greek Keyboard LITE-ON SK-9611 PS/2 105KS Black Danish Keyboard LITE-ON SK-9611 PS/2 104KS Black Czech Keyboard LITE-ON SK-9611 PS/2 105KS Black Romanian Keyboard LITE-ON SK-9611 PS/2 105KS Black Turkish...
  • Page 106 Category Keyboard PRIMAX KB36111 PS/2 104KS Black Thailand Keyboard PRIMAX KB36111 PS/2 105KS Black Spanish Keyboard PRIMAX KB36111 PS/2 105KS Black Portuguese Keyboard PRIMAX KB36111 PS/2 105KS Black Canadian French Keyboard PRIMAX KB36111 PS/2 107KS Black Brazilian Portuguese Keyboard PRIMAX KB36111 PS/2 109KS Black Japanese Keyboard PRIMAX KB36111 PS/2 105KS Black German...
  • Page 107 Category Keyboard PRIMAX KB36111 PS/2 104KS Black Greek Keyboard PRIMAX KB36111 PS/2 105KS Black Danish Keyboard PRIMAX KB36111 PS/2 104KS Black Czech Keyboard PRIMAX KB36111 PS/2 105KS Black Romanian Keyboard PRIMAX KB36111 PS/2 105KS Black Turkish Keyboard PRIMAX KB36111 PS/2 105KS Black Turkish-Q Keyboard PRIMAX KB36111 PS/2 105KS Black Arabic/French...
  • Page 108 Category Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Spanish Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Portuguese Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Canadian French Keyboard PRIMAX KBRF36211 RF2.4 107KS Black Brazilian Portuguese Keyboard PRIMAX KBRF36211 RF2.4 109KS Black Japanese Keyboard PRIMAX KBRF36211 RF2.4 105KS Black German Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Italian...
  • Page 109 Category Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Danish Keyboard PRIMAX KBRF36211 RF2.4 104KS Black Czech Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Romanian Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Turkish Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Turkish-Q Keyboard PRIMAX KBRF36211 RF2.4 105KS Black Arabic/French Keyboard PRIMAX KBRF36211 RF2.4 104KS Black Kazakh...
  • Page 110 Category Keyboard LITE-ON SK-9660B RF2.4 105KS Black Spanish Keyboard LITE-ON SK-9660B RF2.4 105KS Black Portuguese Keyboard LITE-ON SK-9660B RF2.4 105KS Black Canadian French Keyboard LITE-ON SK-9660B RF2.4 107KS Black Brazilian Portuguese Keyboard LITE-ON SK-9660B RF2.4 109KS Black Japanese Keyboard LITE-ON SK-9660B RF2.4 105KS Black German Keyboard LITE-ON SK-9660B RF2.4 105KS Black Italian...
  • Page 111 Category Keyboard LITE-ON SK-9660B RF2.4 105KS Black Danish Keyboard LITE-ON SK-9660B RF2.4 104KS Black Czech Keyboard LITE-ON SK-9660B RF2.4 105KS Black Romanian Keyboard LITE-ON SK-9660B RF2.4 105KS Black Turkish Keyboard LITE-ON SK-9660B RF2.4 105KS Black Turkish-Q Keyboard LITE-ON SK-9660B RF2.4 105KS Black Arabic/French Keyboard LITE-ON SK-9660B RF2.4 104KS Black Kazakh...

Table of Contents