1. Manuals
  2. Brands
  3. Xo Manuals
  4. Ice Maker
  5. XOUIM1565O
  6. Installation and use and care manual

Xo XOUIM1565O Installation And Use And Care Manual

Undercounter gourmet ice maker
Hide thumbs

Advertisement

Table of Contents

XOUIM1565S & XOUIM1565SP
XOUIM1565O & XOUIM1565OP
UNDERCOUNTER GOURMET ICE MAKER
I worked really hard
on this manual -
so please read it...

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XOUIM1565O and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Xo XOUIM1565O

Summary of Contents for Xo XOUIM1565O

  • Page 1 XOUIM1565S & XOUIM1565SP I worked really hard on this manual - XOUIM1565O & XOUIM1565OP so please read it... UNDERCOUNTER GOURMET ICE MAKER...
  • Page 2 Before you proceed, take just a moment to register your XO at: www.xoappliance.com/register-your-product/ REGISTRATION HELPS YOU BY - Ensuring warranty coverage should you need service Providing ownership verification for insurance purposes Let’s XO notify you in the event of product changes or recalls.

  • Page 3: Where Things Are

    where things are Before You Get Started 4 - 7 Installer Checklist Find Your Model Safet y Instructions Electrical and Grounding Instructions Installation Inst ruc tions 8 - 2 3 izes and Installation Dimensions Plumbing With & Without Drain Pump Reversing the Door Door panel Installation Outdoor Use...
  • Page 4 heres’s ten steps for a quick & easy install Inspect cabinet opening for water, drain and electrical connections. The 1/4” O.D. water supply line must include isolation valve and should include an inline water filter (consult manual). Do NOT use a self-piecing valve for the supply connection. Water supply must have a minimum pressure of 20 psi and a maximum of 80 psi.
  • Page 5 INDOOR / OUTDOOR GOURMET ICE MAKER STAINLESS STEEL XOUIM1565S & XOUIM1565SP PANEL READY XOUIM1565O & XOUIM156OP take a minute to circle your model above and record your serial number here in case you need it later...
  • Page 6 For maximum efficiency, keep the door tightly shut unless removing ice. Before installing, allow your XO unit to sit upright for 2 hours at the install site. This will allow the cooling system to stabilize after transportation. Failure to follow this step may cause problems.
  • Page 7 In regions where high humidity exists (greater than 70%) condensation may appear on the door and/or door Your XO unit is built to operate on 115V 60Hz and gaskets. This is normal and will disappear as humidity should be plugged directly into a dedicated 15 amp drops.
  • Page 8 ALL XO UNDERCOUNTER UNITS ARRIVE PRE-WIRED WITH LOW PROFILE PLUGS FOR EASY INSTALLATION 34” MINIMUM (864mm) 7" (178mm) 4" (100mm) 15 ” (381mm) MINIMUM WHEN INSTALLING WITH THE HINGE SIDE NEXT TO A WALL -...

  • Page 9: Top View

    ( or small, as the case would be height & width XOUIM1565G & XOUIM1565GP ICE MAKER 3/4” HIGH (857mm) 14-7/8” WIDE (378mm) depth º TOP VIEW 23-3/8” (594mm) THE OVERALL DEPTH SHOWN (22-5/8”) INCLUDES THE DOOR WITH 3/4” PANEL.
  • Page 10 before you install check a few things Water source valve 115V~60Hz Water source tub Drain hose Is the installation location COOL, DRY, LEVEL and away from direct sun. The water supply valve must provide positive shut off capability and be readily accessible. Does the unit have a dedicated 115V three prong grounded outlet? (use GFI outdoors) The Cold Water supply is 1/4”...

  • Page 11: Water Quality

    All water contains some impurities and minerals. Your XO Ice Maker is designed to produce crystal clear, gourmet ice. It does this by reducing the mineral content in the water as the ice is forming. PURER WATER YIELDS PURER ICE.

  • Page 12: Rear View

    the plumbing Plan the arrangement of the water supply pipes. You will need both a water supply line and a drain (see section on installing a gravity drain unit or pump drain unit) 1/4” O.D. If the tap water has a high level of minerals, an inline filter will be required. Attach the water supply line to the rear of the unit with flexible tube to the fitting indicated here.
  • Page 13 with gravity drain INSTALLING THE XOUIM1565S without a drain pump. Position the ice maker in front of the opening. Level the unit using the leveling legs. Wash and flush the water supply tube and connect the unit to the cold water isolation valve. Prepare the drain.
  • Page 14 with drain pump INSTALLING THE XOUIM1565SP with DRAIN PUMP. Position the ice maker in front of the opening. Level the unit using the leveling legs. Wash and flush the water supply tube and connect the unit to the cold water isolation valve. Cut the 3/8”...

  • Page 15: Reversing The Door

    Your XO Ice Maker is shipped with the hinge on the right hand side but it can be easily reversed. IMPORTANT NOTE: Stainless Steel door models and Panel Ready models use different hinges and Panel Ready models require additional steps when reversing the door.
  • Page 16 reversing the door cont. 3. At the rear of the unit, there are three (3) screws along the top. Remove these screws. TOP COVER On the top front of the unit, there is one (1) additional screw on the left hand side, remove this screw. The Top Cover plate will now lift off.
  • Page 17 & xouim1565op 3/4" 14 3/4" 29 3/8” FRONT MIN. The panel has a minimum height of 29 3/8” - If making the panel 29 3/8” tall no further adjustments are needed. If the panel is taller than 29 3/8”...
  • Page 18 & xouim1565op 14 3/4" Door panels taller than 29 3/8” require a notch as seen in Detail A & B on the hinge side. If making the panel 29 3/8”, no notch (detail A,B) is required.
  • Page 19 & xouim1565op handling handleless doors: Handleless doors have a profile similar to that shown SIDE VIEW REAR VIEW 5/8” 5/8” 1” 29 1/4” TO BOTTOM OF DOOR Instead of a notch, if the design of the door will allow, a recess can be cut out with a router to accommodate the hinge extension.
  • Page 20 installing the overlay panel Installing the overlay panel is easy if you folllow these simple steps. You will need the following tools: A drill with 3/16” and 5/16” bits - and a #2 Phillipshead screwdriver While supporting the door, remove the two (2) screws (shown in RED) that hold the Top Hinge in place.
  • Page 21 installing the overlay panel 5. Center the panel on the door and clamp it in place to prevent shifting during attachment. 6. Using the HINGE ANGLE BRACKETS installed PANEL on the door as a guide, drill two holes: One 3/16” Hole down from the top into the door 1/2” deep. DOOR Remove the plastic bushing from the lower angle bracket.
  • Page 22 installing the overlay panel 10. Remove clamps and any debris that may remain from drilling the pilot holes from the door gasket groove. 11. Beginning at one corner, replace the door gasket by pressing it into the groove it was removed from in Step 2. 12.

  • Page 23: For Outdoor Use

    When using your XO Ice Maker outdoors - follow these additional steps. Di erent regions of the country can have radically di erent seasonal weather which can a ect performance and the influence your selection for the physical location of the unit.

  • Page 24: Features & Specs

    features & specs Produces up to 65lbs of crystal clear, gourmet ice per day Rectangular Bell Shaped Cubes - designed to melt slowly and cool beverages while minimizing dilution Gravity drain and pump drain models available Reversible Panel Ready steel door Front venting - designed for under counter installation Rated for Indoor or Outdoor use (50 - 90 ) Automatically pauses ice production when bin is full...

  • Page 25: Initial Operation

    operating Initial operation ① Open the water supply valve connected with the ice maker. ② Insert the plug of the ice maker into the electric outlet. ③ Open the door and turn the switch to the “ICE” position.” ④ Discard the first batch of ice. ⑤...

  • Page 26: Operation Time

    operating cont. Operation time It takes about 20-35 minutes to produce a set of 24 ice pieces. The length of one cycle of the ice maker (ice production and ice removal) differs depending upon the cleanness of the ice maker, the surrounding temperature, and the temperature of the water supplied to the ice maker.

  • Page 27: Stainless Steel

    stainless steel cleaning the exterior Stainless Steel: Stainless steel does not stain, corrode, or rust as easily as ordinary steel, but it is not stain or corrosion proof. Stainless steels can discolor or corrode if not maintained properly. Stainless steels differ from ordinary carbon steels by the amount metals such as chromium and nickel used in the alloy.
  • Page 28 washing (interior) Proper maintenance, cleaning and santizing is essential to ensure your ice is safe, fresh and odor free. Cleaning the nozzle / ice slide / water tank 1. Open the door and remove two front injection bolts on the top cover. 2.
  • Page 29 washing (interior) cont. Proper maintenance, cleaning and santizing is essential to ensure your ice is safe, fresh and odor free. 5. Clean the gap of the nozzle frame fixed on the vessel sheet (water tank). 6. Lift the drain connection inside the vessel sheet (water tank), clean it, and drain the water.

  • Page 30: Water Tank

    washing (interior) cont. Proper maintenance, cleaning and santizing is essential to ensure your ice is safe, fresh and odor free. Cleaning the ice tank and water tank filters WATER TANK ICE TANK Always unplug the unit before performing maintenance. Open the door of the Ice Maker and remove the filter screens from the bottom of the water tank and ice tank (position indicated above).
  • Page 31 the condenser improve efficiency & performance Cleaning the condenser Remove dust and dirt from the surface of the condenser coils with a vacuum cleaner Remove two screws on the front panel at the center of the inside Vacuum the condenser coils Reassemble the panel using the two screws to after cleaning...
  • Page 32 Maintaining the ice maker according to these instructions will minimize unwanted repairs and extend the unit’s service life. Maintenance activities must be performed either by the consumer or by an authorized service technician at required intervals. If you are unfamiliar with sanitization procedures, contact your dealer or XO Customer Service at 973-403-8900 for service. GENERAL: Thoroughly clean the ice maker every three to six months for efficient operation.
  • Page 33 cleaning cont. If necessary, remove the top cover and disassemble the evaporator cover, water curtain, ice guide and nozzle frame. Place all components into a basin to soak with approximately 3 quarts of the detergent water mixture for 5 to 20 minutes depending on how much lime scale build up is present.
  • Page 34 Maintaining the ice maker according to these instructions will minimize unwanted repairs and extend the unit’s service life. Maintenance activities must be performed either by the consumer or by an authorized service technician at required intervals. If you are unfamiliar with sanitization procedures, contact your dealer or XO Customer Service at 973-403-8900 for service. GENERAL: Sanitize the ice maker every month for safe and efficient operation.

  • Page 35: Maintenance Schedule

    sanitizing cont. Make sure the switch is in the “OFF” position and restore power by plugging the unit in or turning on the breaker. AUTOMATIC SANITIZING: Start the automatic sanitizing process by turning the switch to the “WASH” position. This will also sanitize the piping. The automatic sanitizing cycle takes 21 minutes to complete.
  • Page 36 winterizing Where seasonal installation ambient temperatures fall below 50 F Clean and sanitize your system Turn off the power Empty the water container completely Disconnect the pump hose - this requires the removal of the back panel Close the water supply valve and disconnect the water supply line from the rear of the unit Turn on the power and set the switch to the “WASH”...

  • Page 37: Troubleshooting

    troubleshooting PROBLEM POSSIBLE CAUSE CHECK THIS Unit does not operate Ice maker is unplugged Plug ice maker in Breaker tripped Reset breaker - if it happens again, call for service Switch turned to “OFF” Turn switch to “ICE” The ice tank is full Ice detection sensor is activated Cubes are too large Low ambient temperature...
  • Page 38 OUTSIDE U.S. This warranty does not apply to, and XO is not responsible for, any warranty claims made on products sold or used outside the 48 continental United States.
  • Page 39 notes:...
  • Page 40 SEE ALL THE LATEST XO PRODUCTS AND ACCESS PARTS AT: WWW.XOAPPLIANCE.COM...

This manual is also suitable for:

Xouim1565sXouim1565opXouim1565sp

Table of Contents