Advertisement
Quick Links
SHPE1500, SHPE1500RED, SHPE1500YEL
®
Series SaltDogg
Electric Drive Poly Hopper
Spreader 1.5 cubic yards
Serial Number 9700 and higher.
Protected by U.S. patent D520 524; 9,562,333
Table of Contents
General Information .................................................................... 1
Warranty Information .................................................................. 1
Safety Precautions ..................................................................... 2
Installation Instructions ............................................................2-3
Spreader Operation .................................................................... 4
Spreader Maintenance ............................................................... 5
Repair Parts & Drawings .........................................................6-8
General Information
Spreader model numbers:
• SHPE1500 - spreader with standard chute
• SHPE1500X - spreader with extended chute
Overall Length: 92-1/8"
Overall Width: 50-1/2"
Overall Height (installed): 37-1/2"
Empty Weight: 410 lbs.
Capacity Struck: 1.5 cu. yd.
Average Installation Time: 3 hrs.
Vehicle Requirements
• 3/4 or 1 ton Pickup Truck above 8,500 lbs. GVWR.
• 135 amp or higher alternator is recommended.
Materials Recommended to Spread
CAUTION
Do not overload vehicle beyond the vehicle's GVWR or
GAWR. Check vehicle's load rating certification sticker for
maximum vehicle capacity.
Average Material Weights
Materials to use
Fine Salt-Dry
Coarse Salt-Dry
Sand/Salt up to 50/50 Mix-Dry
Note: To calculate the total spreader weight (including ice
control material), add the empty spreader weight plus the ice
control material and spreader accessories.
Installation Instructions
Weight (pounds per cubic yard)
2,250
1,431
2,700
Phone (440) 974-8888 • Fax (800) 841-8003
SHPE1500 SALTDOGG SPREADER WARRANTY
INFORMATION
This warranty replaces all previous warranties and no
employee of this company is authorized to extend addi-
tional warranties, or agreements, or implications not
explicitly covered herein.
Buyers Products Company warrants all parts of the
product to be free from defects in material and workman-
ship for a period of two (2) years. Parts must be properly
installed and used under normal conditions. Normal wear
is excluded.
Any part, which has been altered, including modifica-
tions, misuse, accident, or lack of maintenance will not
be considered under this warranty.
The sole responsibility of Buyers Products Company
under this warranty is limited to repairing or replacing any
part(s), which are returned, prepaid, 30
days after such defect is discovered, and returned part(s)
are found to be defective by Buyers Products Company.
Authorization from Buyers Products Company must be
obtained before returning any part. The following infor-
mation must accompany defective parts returned
to Buyers Products Company: RMA #, spreader model,
serial number, date installed, and distributor from whom
purchased.
Buyers Products Company shall not be liable for damage
arising out of failure of any unit to operate properly, or
failure, or delay in work, or for any consequential dam-
ages. No charges for transportation or labor performed
on any part will be allowed under this warranty.
1
9049 Tyler Blvd. • Mentor, Ohio 44060
www.saltdogg.com
—continued inside
Advertisement
Related Manuals for Buyers Salt Dogg SHPE1500
Summary of Contents for Buyers Salt Dogg SHPE1500
- Page 1 CAUTION days after such defect is discovered, and returned part(s) Do not overload vehicle beyond the vehicle’s GVWR or are found to be defective by Buyers Products Company. GAWR. Check vehicle's load rating certification sticker for maximum vehicle capacity. Authorization from Buyers Products Company must be obtained before returning any part.
- Page 2 Safety Precautions D. Slide spreader forward until the steps on rear legs of the spreader make contact with truck’s bed. Measure the distance WARNING from the front of the truck bed to front of the hopper's front legs. Fabricate spacer to fit between front of the spreader and Observe the following Safety Precautions before, during and front of the bed as shown in Figures 2 &...
- Page 3 2. Mounting the Spinner/Chute Assembly WARNING A. Attach the Chute Assembly to the spreader. First, hook the Do not drill holes into fuel tanks, fuel lines, through electrical Chute to the spreader by openings in the Chute’s handle (Fig. wiring, etc that may be damaged by drilling. 3.
- Page 4 3001379 Fig. 7 CB120PB BATTERY POSITIVE BATTERY NEGATIVE 3035933 3006724 3014199 Thoroughly clean battery terminals. Make sure battery To start the spreader, press the ON-OFF switch. Switch will terminals have no tarnish or corrosion. illuminate. The auger will accelerate to full speed for 2 seconds, then slow down to dialed speed.
- Page 5 Spread Pattern Adjustment 4. Inspect terminals/connectors every time you disconnect spreader from wire harness. Apply thin layer of dielectric grease Spread pattern can be adjusted by changing spinner disc speed on terminals. If any tarnish/corrosion is found, clean terminals on controller by turning Spinner knob to desired speed level and apply dielectric grease.
- Page 6 Repair Parts - Standard Chute Assembly Repair Parts - Extended Chute Assembly Bill of Materials Bill of Materials ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 3025063 CHUTE POLY, SHPE STD. LENGTH 3007526 CHUTE POLY. EXT. LENGTH 3033665 BRACKET WELDMENT, CHUTE 3006833 GEAR MOTOR 12 VDC.
- Page 7 Repair Parts-Hopper Assembly Bill of Materials ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 9240132 DECAL #2, DANGER BEFORE SVCE 3005574 HOPPER POLY 1.5 CU. YA., BLACK 3007731 BRACKET VIBRATOR, LONG SST 3025162 HOPPER POLY 1.5 CU. YA., RED FNE038016044SS NUT, NYLOCK 3/8-16 X 7/16 SST 3025164...
- Page 8 9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (800) 841-8003 www.saltdogg.com Repair Parts-Trough Assembly Repair Parts-Spreader Bill of Materials ITEM PART NO. QTY. DESCRIPTION 3007357 TROUGH WELDMENT SHPE1500 3007000 GASKET, FELT BEARING 3018919 BEARING, 2-HOLE FLANGED 1" SST FNE038016044SS NUT, NYLOCK 3/8-16 X 7/16 SST 3018007...