Specific Safety Rules - Matco Tools MCL16RDG Operating Instructions Manual

• Never mount a grinding wheel, cutoff wheel, router
cutter or drill bit on Die Grinder.
• Do not lock, tape or wire the "on/off" safety lever in the
"on" position, as the lever must be free to return to the
"off" position when released.
• This product may contain one or more chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands thoroughly
after handling.
• Failure to heed these warnings may result in personal injury
and/or property damage.
Service
• Tool service must be performed only by the MATCO
authorized service centers listed. Service or maintenance
performed by unqualified personnel may result in a risk of
injury. Repair by unqualified personnel, use of unauthorized
parts, and failure to follow maintenance instructions may
create a risk of shock or injury.
SAVE THESE INSTRUCTIONS!

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product replace strict
adherence to cordless product safety rules. If you use this
OPERATING INSTRUCTION
Installing Or Removing Battery Pack
1. Your new battery pack is not fully charged. You may need to
charge before use.
2. Make sure the tool is off when installing or removing a
battery.
3. To remove a battery pack, depress both tabs on either side of
the battery and pull downward.
4. To insert a battery pack, align the battery with the tool
housing and push battery inward until click indicating battery
is fully installed.
Charging The Battery Pack
1. Battery may not charge when it is above a certain preset
temperature limit. Allow temperature of battery to cool before
charging.
2. The charge process will take less than one hour.
3. After charging, unplug the charger from the power source
and stow away in a safe place.
MCL16RDG
MCL16RDG 16V RIGHT ANGLE DIE GRINDER
tool unsafely or incorrectly, you can suffer serious personal
injury.
• Hold tool by insulated gripping surfaces when performing an
operation where the accessories may contact hidden wiring.
Contact with a "live" wire will also make exposed metal parts of
the tool "live" and shock the operator.
• Be aware that this tool is always in operating condition, because it
does not have to be plugged into an electrical outlet.
• Always be sure you have firm footing.
• Be sure no one is below when using the tool in high locations.
• Hold the tool firmly and use both hands.
• Do not leave the tool running. Do not force tool to stay in the "on"
position. Operate the tool only when hand-held.
• Some material contains chemicals which may be toxic. Take
caution to prevent working dust inhalation and skin contact.
Follow material supplier safety data.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
Tool Operation and Maintenance Instructions
Bonded abrasive mounted point grinding wheels, rotary
files and carbide burrs can be mounted providing their
speed rating exceeds the speed of the Die Grinder. The
shank size of the mounted accessory must match the collet
size fitted in the Die Grinder. Insert the shank of the
mounted point as far as possible into the collet and tighten
the nut using the supplied wrenches. Minimum shank
gripping length must be 10mm.
After mounting a new point, start the Die Grinder under
bench and run for a few seconds. If the Die Grinder starts
to vibrate when first fitting a mounted point or during
operation, immediately remove from service. If Die Grinder
is dropped, replace bonded abrasive mounted point
grinding wheel, rotary file or carbide burr. When using the
Die Grinder, be careful not to exert excessive force
which could be hazardous and cause mounted spindle to
bend or break.
NOTE: During operation, safety goggles should
always be worn to guard against flying debris (users
and bystanders).
Important Lubrication Instructions
Lubricate through angle gear head grease fitting
using MG62 mini grease gun every 8 hours of use
for maximum gear life.
Grease Fitting
3 rev. 07/25/16