Subscribe to Our Youtube Channel
Related Manuals for Trust 200SA
Summary of Contents for Trust 200SA
- Page 1 Trust Wireless Alarm System 200SA TRUST WIRELESS ALARM SYSTEM 200SA Instruction Manual Version 1.1...
- Page 2 Trust Wireless Alarm System 200SA Thank you Thank you very much for purchasing this product from the Trust range. We wish you hours of fun with it. Please read this manual carefully before using the product. Registration Register your purchase now at the Trust Internet site, www.trust.com, so that you are able to receive optimal guarantee and service support.
-
Page 3: Table Of Contents
Alarm centre..........................4 Motion detector (Trust Wireless Motion Detector 200DM)........... 5 Magnetic contact (Trust Wireless Alarm Switch 200DS)............6 Remote control (Trust Wireless Remote Controller 200RC) ..........7 Installation ............................8 Setting the home code......................8 Setting the zone........................8 Wireless motion detector installation .................. -
Page 4: Introduction
Trust Wireless Alarm System 200SA 1. Introduction This manual is intended for users of the Trust Wireless Alarm System 200SA. In case of doubt, consult one of the Trust Customer Care Centres. The last page of this manual contains more information about these Customer Care Centres. -
Page 5: Safety
Trust Wireless Alarm System 200SA 2. Safety General Do not use the device in damp environments such as bathrooms, swimming pools etc. Do not try to repair the device yourself. Under the following circumstances have the device repaired by qualified personnel: a) The cable or plug is damaged or worn;... -
Page 6: Function Description
Trust Wireless Alarm System 200SA 3. Function description Before you install the alarm system, you must first become familiar with the functions of the various components of the alarm system. See the chapters below for the function description of the various... -
Page 7: Motion Detector (Trust Wireless Motion Detector 200Dm)
The alarm centre can be expanded to an unlimited extent with the following wireless transmitters: Motion detector (Trust Wireless Motion Detector 200DM) For securing entire rooms. The motion detector has a detection angle of 110 º. The detector responds to sudden temperature changes within its detection area. -
Page 8: Magnetic Contact (Trust Wireless Alarm Switch 200Ds)
Switch to the ON mode for normal use. Magnetic contact (Trust Wireless Alarm Switch 200DS) For securing windows and doors. As soon as the contact is broken, so if a window or door is opened, the magnetic contact will transmit a signal to the alarm centre. The magnetic contact is also equipped with a panic button in order to be able to activate the alarm in case of emergency. -
Page 9: Remote Control (Trust Wireless Remote Controller 200Rc)
Trust Wireless Alarm System 200SA Remote control (Trust Wireless Remote Controller 200RC) The alarm system can be entirely operated with the enclosed remote control. Several remote controls can be used. This is handy when more than one person (housemates, for example) must be able to operate the alarm system. -
Page 10: Installation
Trust Wireless Alarm System 200SA 4. Installation Before installing the alarm centre you must first install the wireless accessories (motion detector, magnetic contact, etc.) and set the zone and home code of every accessory. This is because the alarm centre automatically detects and programs the home code at the first activation. -
Page 11: Wireless Motion Detector Installation
Trust Wireless Alarm System 200SA Wireless motion detector installation Figure 6: motion detector installation For installation of the wireless motion detector follow the steps below: 1. Remove the front protector plate of the motion detector with a small coin or screwdriver by placing it between the edge of the front and rear protector plates and clicking the plate loose. -
Page 12: Wireless Magnetic Contact Installation
Trust Wireless Alarm System 200SA Wireless magnetic contact installation Figure 7: Magnetic contact installation For installation of the wireless magnetic contact follow the steps below: 1. Remove the cover of the magnetic contact with a small coin or screwdriver by placing it between the edges of the cover (A) and clicking it loose. -
Page 13: Remote Control Installation
Trust Wireless Alarm System 200SA Remote control installation Figure 8: remote control installation For installation of the remote control follow the steps below: 1. Remove the rear protector plate of the remote control by loosening the 2 screws with a small screwdriver. -
Page 14: Alarm Centre Installation
Trust Wireless Alarm System 200SA Alarm centre installation Figure 9: alarm centre installation Note: First install the accessories included (wireless motion protector, wireless magnetic contact, etc.), before installing the alarm centre. Also make sure that the magnetic contact is closed (door or window closed). -
Page 15: Determining The Best Location For The Alarm Centre
Trust Wireless Alarm System 200SA 13. Learn the home code: The alarm centre uses a technique that ‘learns’ the home code automatically. Therefore, there is no DIP switch in the alarm centre. If you have set the same home code in the wireless motion detector, the magnetic contact and the remote control, press the “Completely on/off button”... -
Page 16: Testing The Wireless Magnetic Contact
Trust Wireless Alarm System 200SA Testing the wireless magnetic contact. 1. Make sure that the home code is the same as that of the motion detector and the remote control. 2. Press the ‘Panic’ button of the magnetic contact. If the alarm goes off, the button is functioning correctly. - Page 17 Trust Wireless Alarm System 200SA Code Description Switching the home mode off again: Input the same code once more for switching off the home mode. After entering the code you will hear 2 beeps as confirmation. Setting the dial mode: Enter this code to switch the phone selector between the “pulse”...
- Page 18 Trust Wireless Alarm System 200SA Code Description Recording and playing back voice messages: Record short voice messages that are played back automatically when calling the telephone numbers you entered. The 7-segment display presents the following: “Recording”, enter [4-digit code] [REC] [1-4] to record a voice message.
-
Page 19: Resetting The Alarm System
Trust Wireless Alarm System 200SA Code Description Telephone numbers for pagers: Instead of the 6 numbers for voice messages you can also set the 6 numbers of group “T1” for calling a pager Enter the page number at ‘Number’ and the number you want to leave the receiver at ‘Code’, such as your... -
Page 20: Setting Telephone Numbers
Trust Wireless Alarm System 200SA 7. Setting telephone numbers The possible telephone numbers are subdivided into 2 groups. The first group (T1) is for voice messages and the second group (T2) is for digital communication. Group T1 has 6 telephone numbers for voice messages. All 6 of these can also be used for pager applications. -
Page 21: Activation
Activation If the Trust Wireless Alarm System 200SA is activated (the alarm goes off), the built-in telephone selector will automatically call the telephone numbers in its memory and play the voice messages. See chapter 6.1. The sequence of calling is first the consecutive numbers of group “T2” and then those of group “T1”. For each telephone number one of the 3 short voice messages will be played first (depending on the type of alarm), followed by the detailed voice message. -
Page 22: Advanced Settings
Trust Wireless Alarm System 200SA Figure 11: installation of additional accessories on clamp strip Function Description Power connection for eternal accessories EXT. Active low-voltage output for switching on the accessories Ground connection. Advanced settings Code Description Setting output for external siren: Enter this code if you have connected an external siren. - Page 23 Trust Wireless Alarm System 200SA Code Description The 7-segment display presents the following: This output is a 200mA active low-voltage output. When using a small LED as indicator, a resistor must be used to limit the current (2 kOhm, ¼ W resistor for normal LED).
-
Page 24: Example Of Several Magnetic Contacts
Trust Wireless Alarm System 200SA Figure 13: wiring diagram for external accessories Example of several magnetic contacts The enclosed wireless magnetic contact can also be expanded with extra magnetic sensors via the incorporated 2-pole clamp strip in order to be able to secure several doors or windows via 1 transmitter. -
Page 25: Questions & Answers
Trust Wireless Alarm System 200SA 9. Questions & answers Question Answer What is the difference between the With the security code you can switch the alarm on and off and adapt all settings via the keyboard. With the home code,... - Page 26 Trust Wireless Alarm System 200SA Question Answer How can I replace the batteries of You can enter the code [your security code] [*] [9] to switch the detectors without setting off the off the alarm temporarily. You will then have 10 minutes before the system switches on again automatically.
- Page 27 You will be automatically informed of developments to your product and of other Trust products. You will also have the chance to win some spectacular prizes. If you still have any problems after trying these solutions, please contact one of the Trust Customer Care Centres.
-
Page 28: Specifications
Trust Wireless Alarm System 200SA 10. Specifications Alarm centre Transmission frequency 433MHz; with a maximum of 6561 channels (home code) programmable. Transmission range 50 meters in a free area without obstacles or interference. Operating voltage 7.2 – 12VDC Electricity consumption when in use Internal 250mA (max);... -
Page 29: Trust Customer Care Centres
Trust Wireless Alarm System 200SA 11. Trust Customer Care Centres www.trust.com Residents in the UK and Ireland should contact: From UK Office 8:00 - 16:00 Phone +44-(0)0845-6090036 +44-(0)1376-514633 I residenti in Italia possono contattare: Orario: Ufficio italiano 9:00 - 13:00 /...
Need help?
Do you have a question about the 200SA and is the answer not in the manual?
Questions and answers