Before Using The Unit - Maxwell MW-1853 BK Manual Instruction

• Never use the unit if the power cord or the
power plug is damaged, if the unit works
improperly or after it was dropped.
•
Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and apply to any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.maxwell-products.ru.
• Transport the unit in the original package
only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES
IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least 3 hours at
room temperature before switching on.
Unpack the unit completely and remove any
stickers that can prevent unit operation.
Remove the packaging materials and any acces-
sories from the process chamber.
Check the unit for damages; do not use it in case
of damages.
SETTING
Set the mini-oven on a flat and hard surface
–
that will bear its weight and max. weight of
the products, which will be cooked in it.
Do not place the unit in places with high
–
moisture and temperature, and near inflam-
mable objects.
Choose the place that is out of the reach of
–
small children.
Place the mini-oven keeping at least a 20 cm
–
gap from the sides and the rear of the oven
to the wall and a 30 cm gap above the unit.
– Do not remove the support legs (1) from the
body bottom.
Do not block the ventilation openings in the
–
unit body (4).
CONNECTING THE MINI-OVEN
Before connecting the mini-oven, make sure
–
that the operating voltage and the power
consumption of the unit correspond to the
specifications of your mains.
IM MW-1853.indd 9
To avoid fire, do not use adapters for con-
–
necting the unit to the mains.
Connect the mini-oven to a mains socket with
–
reliable grounding contact.
Connection of plug with a grounding contact
–
to the socket without grounding can lead to
the risk of electric shock.
Consult a qualified electrician, if the ground-
–
ing instructions are not completely clear for
you or if you are not sure that the roaster
body is securely grounded.
If it is necessary to use the extension cord,
–
use only a 3-wire extension cord with a
grounding contact on the power cord plug
and the socket.
Wire section marking of the roaster power
–
cord and of the extension cord should match.
– The power cable and the extension cord
should not hang from the edges of the table,
where children can pull the cord and it should
be placed in such a way that excludes possi-
bility of stepping on it.

BEFORE USING THE UNIT

Wash the rack (11), the baking tray (10) and the
handle (9) with warm water and neutral detergent
and dry them thoroughly.
Insert the power plug into the mains socket.
Switch the unit on in the maximal heating mode,
turning the control knob «TEMPERATURE» (5)
and setting it to the position «250».
Turn the "TIMER" knob (8) clockwise and set
the operation time 10-15 minutes, the unit will
be switched on and the indicator (6) will light
up. After the operation time is up, you'll hear a
sound signal.
Note: during the first operation some foreign
smell and a small amount of smoke from the
heating element is possible, this is normal.
ACCESSORIES
Rack (11)
Use the rack to roast or defrost products. To pre-
vent the lower heating element from getting dirty
always set the baking tray (10) under the rack.
Remove the rack from the process chamber by
the handle (9).
Baking tray (10)
Use the baking tray for cooking products and
for protecting the lower heating element from
dirt (place the baking tray under the rack (11)).
The baking tray (10) gets hot during operation,
9
ENGLISH
12/15/17 11:57 AM