Page 1
For a Spanish version of this manual, visit our Website at GEAppliances.com. Para consultar una version en español de MFL59060930_00 este manual de instrucciones, visite nuestro sitio de internet GEAppliances.com. 31-2000001-7 12-21 GEA GE is a trademark of the General Electric Company. Manufactured under trademark license.
Safety Information CONTENTS BEFORE YOU BEGIN Design Information Read these instructions completely and Models Available ..........2 carefully. Product Dimensions and Clearances ....3 IMPORTANT — Save these instructions Tools Required ..........3 for local inspector’s use. Parts Supplied ........... 3 IMPORTANT —...
Design Information PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model. 21-1/2 29-3/4 1-3/16 TOOLS AND PARTS REQUIRED ADVANCE PLANNING • (NOT SUPPLIED wide oven cabinet with standard installation. • #2 Phillips screwdriver • Cutout height dimensions are different for •...
Page 4
Installation Preparation ELECTRICAL REQUIREMENTS Single Advantium/Convection 120 Installation: This product requires a 120-volt, 60 Hz, 15-amp circuit and draws 1.8 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. • Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating.
Page 5
Standard Installation Preparation IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed. PREPARE THE OPENING PREPARE THE OPENING (CONT.) The Advantium/Convection 120 can be installed Installation over a Warming Drawer: in combination with other Built-In Appliances.
Page 6
Standard Installation Preparation IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed. PREPARE THE OPENING (CONT.) PREPARE THE OPENING (CONT.) Installation over a Wall Oven: Installation over a Wall Oven and Construct Warming Drawer: 23-1/2”...
Standard Installation Preparation IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed. PREPARE THE OPENING (cont.) PREPARE THE OPENING (cont.) Installation over another Built-In Installation under a Microwave Oven and SpeedCook Oven: over a Warming Drawer: Construct...
Page 8
Standard Installation Preparation IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed. PREPARE THE OPENING (cont.) 23-1/2 Installation beside another Built-in Speedcook Oven: • If you are mounting a SpeedCook Oven beside another, use the dimensions shown.
Flush Mount Installation Preparation (Monogram Only) IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed. PREPARE THE INTERIOR PREPARE THE OPENING Cut and install side cleats: The Advantium 120 can be installed in •...
Page 10
Flush Mount Installation Preparation (Monogram Only) IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed. PREPARE THE OPENING 23-1/2” min. The Advantium/Convection 120 can be installed beside another Advantium/Convection 120 in a side-by-side combination.
Page 11
Installation Preparation WITH Preparation an Accessory Storage Drawer • PSB9120 and PWB7030 are the only approved models to be installed under 36-3/4” height with a storage drawer. CSB9120, ZSC1201, ZSC1202 and CWB7030 are not approved. • As needed, see the Standard Mount Installation Preparation OR Flush Mount Installation Preparation for configuration details.
Installation Instructions 1 REMOVE THE PACKAGING AND PARTS • Remove all packing material and tape. 4 Color-Matched Flat-Head Screws • Locate parts package containing mounting for the Plastic Door Trim (3 required, screws. 1 extra) • Remove the oven from the carton. Do not lift unit *Some models already have the trim by handle or conduit.
Installation Instructions 2 DOOR TRIM REMOVAL FOR 3 SLIDE THE OVEN INTO THE ABOVE 36 INSTALLATION CUTOUT ONLY CAUTION Two people are required to lift If installing the Advantium/Convection 120V the oven into the opening. Grasp the bottom at Oven above 36 from the floor, you may remove front and rear.
Installation Instructions 4 INSTALL BOTTOM TRIM 6 INSTALL MOUNTING SCREWS CAUTION If installing the Advantium/ Convection 120V Oven below 36 , you must use the plastic bottom trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot surfaces.
Page 16
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor at GE Appliances. Therefore, materials, appearance and specifications are subject to change without notice. Printed in China...
Page 17
Instalación Hornos con Velocidad de Cocción/Convección Incoporada de 120V de Advantium ® CSB9120 PSB9120 ZSC1201 ZSC1202 CWB7030 PWB7030 CWB713 MFL59060930_00 31-2000001-7 12-21 GEA GE es una marca de la Empresa General Electric. Fabricado bajo licencia de la marca registrada.
Page 18
Información sobre Seguridad CONTENIDOS ANTES DE COMENZAR Información de Diseños Lea estas instrucciones en su totalidad y Modelos Disponibles ..........2 atentamente. Dimensiones y Espacios de Despeje del Producto .. 3 IMPORTANTE — Conserve estas instrucciones Herramientas Necesarias .......... 3 para uso del inspector local.
Información de Diseños DIMENSIONES Y ESPACIOS DE DESPEJE DEL PRODUCTO NOTA:El aspecto variará dependiendo del modelo. 21-1/2 29-3/4 1-3/16 HERRAMIENTAS Y PLANIFICACIÓN ANTICIPADA PIEZAS REQUERIDAS (NO • Estos hornos pueden ser instalados directamente en un gabinete para horno de 30” de ancho, utilizando la SUMINISTRADAS) instalación estándar.
Preparación de la Instalación REQUISITOS ELÉCTRICOS Instalación Simple del Advantium/ Convección 120: Este producto requiere un circuito de 120 voltios, 60 Hz, 15 amperes y consume 1.8 kilowatts. Este producto se debe conectar a un circuito con un suministro correcto de voltaje y frecuencia.
Preparación de la Instalación Estándar IMPORTANTE: Siempre deje una altura mínima de 36 ¾” desde el piso hasta el recorte en cualquier instalación, ya sea simple o combinada, a menos que se instale una moldura de plástico. PREPARACIÓN DE LA ABERTURA PREPARACIÓN DE LA ABERTURA (CONT.) El Advantium 120 se podrá...
Page 22
Preparación para la Instalación Estándar IMPORTANTE: Siempre deje una altura mínima de 36 ¾” desde el piso hasta el recorte en cualquier instalación, ya sea simple o combinada, a menos que se instale una moldura de plástico. PREPARACIÓN DE LA ABERTURA PREPARACIÓN DE LA ABERTURA (CONT.) (CONT.)
Page 23
Preparación para la Instalación Estándar IMPORTANTE: Siempre deje una altura mínima de 36 ¾” desde el piso hasta el recorte en cualquier instalación, ya sea simple o combinada, a menos que se instale una moldura de plástico. PREPARACIÓN DE LA ABERTURA PREPARACIÓN DE LA ABERTURA (cont.) (cont.)
Page 24
Preparación para la Instalación Estándar IMPORTANTE: Siempre deje una altura mínima de 36 ¾” desde el piso hasta el recorte en cualquier instalación, ya sea simple o combinada, a menos que se instale una moldura de plástico. 23-1/2 PREPARACIÓN DE LA ABERTURA (cont.) Instalación junto a otro Horno con Velocidad de Cocción Incorporada:...
Preparación de la Instalación para el Montaje al Ras (Monogram Únicamente) IMPORTANTE: Siempre deje una altura mínima de 36 ¾” desde el piso hasta el recorte en cualquier instalación, ya sea simple o combinada, a menos que se instale una moldura de plástico. PREPARE EL INTERIOR PREPARACIÓN DE LA ABERTURA Corte e instale los ristreles laterales:...
Page 26
Preparación de la Instalación para el Montaje al Ras (Monogram Únicamente) IMPORTANTE: Siempre deje una altura mínima de 36 ¾” desde el piso hasta el recorte en cualquier instalación, ya sea simple o combinada, a menos que se instale una moldura de plástico. PREPARACIÓN DE LA ABERTURA Mín.
Page 27
Preparación de la Instalación Preparación CON un Cajón de Almacenamiento de Accesorios • PSB9120 y PWB7030 son los únicos modelos aprobados para su instalación debajo de una altura de 36 3/4” con un cajón de almacenamiento. CSB9120, ZSC1201, ZSC1202 y CWB7030 no están aprobados.
Instrucciones de Instalación 1 RETIRE EL EMBALAJE Y LAS PIEZAS • Retire todo el material de embalaje y la cinta. 4 Tornillos de Cabeza Plana del Mismo Color para la Moldura de la Puerta de • Ubique el paquete de piezas que contiene los tornillos Plástico de montaje.
Instrucciones de Instalación 2 RETIRO DE LA MOLDURA DE 3 DESLICE EL HORNO POR LA LA PUERTA PARA ABERTURA INSTALACIONES SUPERIORES Se requiere contar con dos A 36” ÚNICAMENTE PRECAUCIÓN personas para colocar el horno en la abertura. Se deberá tomar la parte inferior sobre la Si instalará...
Instrucciones de Instalación 4 INSTALE LA MOLDURA 6 INSTALACIÓN DE LOS TORNILLOS DE MONTAJE INFERIOR Si instalará el Horno Advantium/ PRECAUCIÓN Convección 120V por debajo de 36”, deberá usar el borde inferior de plástico debido a riesgos de quemaduras de los niños. El borde de plástico actúa como aislante y ayudará...
Page 32
NOTA: Al realizar las instalaciones descriptas en este libro, se deberán usar anteojos o gafas de seguridad. NOTA: GE Appliances se esfuerza de forma constante para mejorar sus productos. Por lo tanto, los materiales, el aspecto y las especificaciones están sujetos a cambios sin aviso previo.