Advertisement

Specifications
Power Source :
Power Consumption :
Aerial Impedance :
Receiving System :
Receiving Channels :
VHF
UHF
CATV
Intermediate Frequency :
Video
Sound
AC AUTO 110-240V, 50/60 Hz
75Ω unbalanced
Coaxial type
17 Systems
1-11 PAL B (Australia & N.Zealand)
1-12 PAL/SECAM D
1-12 NTSC M JAPAN
2-12 PAL/SECAM B, G
2-13 NTSC M U.S.A.
21-69 PAL G I/SECAM B, G, K1
28-69 PAL G (Australia)
13-56 PAL D
13-52 NTSC M JAPAN
14-69 NTSC NTSC M U.S.A.
S1-S41 (Hyper)
38.0 MHz
31.5 MHz (D, K, K1)
32 MHz (I)
32.5 MHz (B, G)
33.5 MHz (M)
TC-14Z99M
GP31 Chassis
Colour
56W
Video / Terminals :
RAV In
Monitor Out
High Voltage :
Picture Tube :
Audio Output :
Dimensions :
Mass :
Specifications are subject to change without notice.
Mass and dimensions shown are approximate.
ORDER NO. PMI-T0705-01
Colour Television
33.75 MHz (SECAM)
Audio In Approx. 400mVrms
Video Out 1 Vp-p 75Ω
Audio Out Approx. 400mVrms
at zero beam current
Measured diagonally,
© 2005 Matsushita Electric Industrial Co., Ltd. All
rights
reserved.
Unauthorized
distribution is a violation of law.
33.57 MHz (PAL)
33.6 MHz (SECAM)
34.42 MHz (NTSC)
AV1, 2
Video In 1 Vp-p 75Ω
23.5kV±1.5
37GDC86XTC02
37cm (14 inches)
90° deflection
5W
Height : 353 mm
Width : 447 mm
Depth : 370 mm
10 kg (Net Wt.)
copying
and

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TC-14Z99M and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Panasonic TC-14Z99M

  • Page 1 ORDER NO. PMI-T0705-01 Colour Television TC-14Z99M GP31 Chassis Specifications Power Source : AC AUTO 110-240V, 50/60 Hz Colour 33.57 MHz (PAL) Power Consumption : 33.6 MHz (SECAM) Aerial Impedance : 75Ω unbalanced 33.75 MHz (SECAM) Coaxial type 34.42 MHz (NTSC)
  • Page 2: Table Of Contents

    TC-14Z99M CONTENTS Page Page 1 Safety Precautions 2.7. PAL Colour Output Level Adjustment 1.1. General Guide Lines 2.8. CRT VRS Adjustment 1.2. Leakage Current Cold Check 2.9. CRT Cut Off Adjustment 1.3. Leakage Current Hot Check (Fig. 1) 2.10. Purity and Convergen Adjustment 1.4.
  • Page 3: Safety Precautions

    TC-14Z99M 1 Safety Precautions 1.1. General Guide Lines 1. It is advisable to insert an isolation transformer in the AC supply before servicing this hot chassis. 2. When servicing, observe the original lead dress, especially the lead dress in the high voltage circuits. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
  • Page 4: Gp31 Chassis Block Diagram

    TC-14Z99M 1.5. GP31 Chassis Block Diagram...
  • Page 5: Service Hints

    TC-14Z99M 2 Service Hints 2.1. Service Position for E-Board 1. Remove the back cover. 2. Stand the TV set as shown in Fig. 2. 3. Remove the A-Board from the TV set by pulling the main board out as shown in Figure 2.
  • Page 6: B Voltage Adjustment

    TC-14Z99M 2.3. +B Voltage Adjustment 2.5. RF AGC Adjustment Item / preparation Item / preparation 1. Operate the TV set. 1. Receive a colour bar signal at an RF level of 69 ± 1-2 dBU with 75Ω loaded. 2. Set control as follows : 2.
  • Page 7: Pal Colour Output Level Adjustment

    TC-14Z99M 2.7. PAL Colour Output Level Adjustment 1. Receive the PAL B/G studio colour bar pattern and adjust local frequency at the best tuned position. 2. Pic Menu: Dynamic Normal, Confirm Contrast - 100 DAC, Sub Contrast - 21 dac.
  • Page 8: Crt Vrs Adjustment

    TC-14Z99M 2.8. CRT VRS Adjustment Adjustment of CRT VRS 1. Preparation a. Set DY to CRT not to tilt up and down left and right deflection. b. Set CY to CRT and set CY magnet primarily (Fig. 1) Purity magnet : Set purity magnet that 2 magnets are (TOP POSITION) VRS magnet : Set purity magnet 2 magnets are (HORIZONTAL POSITION) 2.
  • Page 9 TC-14Z99M Fig. 10 Fig. 11 Notes: 1. Wedge A, B and C should be inserted following the sequence of 1, 2 and 3 shown in Fig. 11. 2. The wedges should be set 120° apart from each other. 3. Be certain that three wedges are firmly fixed and the Deflection Yoke is tightly clamped in place.
  • Page 10: Crt Cut Off Adjustment

    TC-14Z99M 2.9. CRT Cut Off Adjustment Preparation: 1. Connect the oscilloscope probe to TPL5. 2. Screen VR min. 3. Set the data Sub Bright, Bright. 4. In service Mode at “Bright” dac press [5] in factory mode to enter vertical line and adjust by volume down or up button.
  • Page 11: White Balance Adjustment

    TC-14Z99M Convergence 1. Apply a crosshatch pattern signal and Normalize Contrast 4. Adjust Red and Blue with Green line at centre of the screen control to the maximum positions. by rotating (RB)-G static convergence magnetic rings. 2. Adjust Brightness until the grey position of the crosshatch 5.
  • Page 12: Conductor Views

    TC-14Z99M 3 Conductor Views...
  • Page 13: Schematic Diagram

    TC-14Z99M 4 Schematic Diagram...
  • Page 14 TC-14Z99M...
  • Page 15: A Board

    TC-14Z99M 4.1. A Board 4.1.1. A Board (1/5) <1A> <2A> <3A> <4A> <5A> <6A> <7A> <8A> <9A>...
  • Page 16 TC-14Z99M 4.1.2. A Board (2/5) <1A> <1B> <2B> <2A> <3B> <3A> <4A> <4B> <5A> <5B> <6A> <6B> <7B> <7A> <8B> <8A> <9A> <9B>...
  • Page 17 TC-14Z99M 4.1.3. A Board (3/5) <1B> <1C> <2C> <2B> <3C> <3B> <4C> <5C> <4B> <6C> <5B> <7C> <6B> <7B> <8B> <8C> <9B> <9C>...
  • Page 18 TC-14Z99M 4.1.4. A Board (4/5) <1C> <1D> <2C> <2D> <3C> <3D> <4D> <4C> <5C> <6C> <5D> <7C> <6D> <7D> <8C> <9C>...
  • Page 19 TC-14Z99M 4.1.5. A Board (5/5) <1D> <2D> <3D> <4D> <5D> <6D> <7D>...
  • Page 20: L Board

    TC-14Z99M 4.2. L Board 4.2.1. L Board (1/3) <1A> <2A> <3A> <4A> <5A> <6A> <7A>...
  • Page 21 TC-14Z99M 4.2.2. L Board (2/3) <1A> <1B> <2A> <2B> <3A> <4A> <5A> <3B> <4B> <5B> <6A> <6B> <7A>...
  • Page 22 TC-14Z99M 4.2.3. L Board (3/3) <1B> <2B> <3B> <4B> <5B> <6B>...
  • Page 23: Parts Locations

    TC-14Z99M 5 Parts Locations...
  • Page 24: Replacement Parts List

    TC-14Z99M 6 Replacement Parts List...
  • Page 25: Replacement Parts List

    TC-14Z99M 6.1. Replacement Parts List Ref. Part No. Part Name & Description Remarks C3151 ECJ2VF1C105Z C 1F, Z, 16V Ref. Part No. Part Name & Description Remarks C3153 ECJ2VF1C105Z C 1F, Z, 16V C3155 ECJ2VF1C105Z C 1F, Z, 16V 37GDC86XTC02...
  • Page 26 TC-14Z99M Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C670 F2A1C100A180 E 10F, 16V D512 MA2B17100E DIODE C680 ECJ2YB1H473K C 0.047F, K, 50V D513 B0HAJP000015 DIODE C685 ECJ2VC1H101K C 100PF, K, 50V...
  • Page 27 TC-14Z99M Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks L873 J0JKA0000024 BEAD CORE R1130 D0GD101JA017 F 100OHM, J, 1/10W TRANSISTOR R1131 D0GD101JA017 F 100OHM, J, 1/10W Q001 B1ABCE000015 TRANSISTOR R1132 D0GD101JA017 F 100OHM, J, 1/10W...
  • Page 28 TC-14Z99M Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R406 ERDS1FJ1R0T C 1OHM, J, 1/2W R832 D0AE473JA046 C 47KOHM, J, 1/4W R407 ERG2FJ331H M 330OHM, J, 2W R840 ERD75TAJ825 C 8.2MOHM, J, 3/4W...
  • Page 29 TC-14Z99M Ref. Part No. Part Name & Description Remarks SW1002 EVQ11G05R TOUCH SWITCH SW1003 EVQ11G05R TOUCH SWITCH SW1004 EVQ11G05R TOUCH SWITCH SW1005 EVQ11G05R TOUCH SWITCH SW1006 EVQ11G05R TOUCH SWITCH SW801 ESB92DA1B POWER SWITCH TU001 ENV59K01G3YF TUNER X180 EFCS5M7MW3 CERAMIC FILTER...

Table of Contents