Summary of Contents for Bush Hog Commercial Series
Page 1
BUSH HOG ® COMMERCIAL SERIES Z Z e e r r o o T T u u r r n n M M o o w w e e r r Operator’s Manual ASSEMBLY l l OPERATION l l MAINTENANCE $4.00...
Page 3
COMMERCIAL SERIES ZERO TURN RIDING MOWER TABLE OF CONTENTS SECTION PAGE SECTION PAGE RETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY...
Page 4
OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO NOTE: This warranty covers parts and labor for the first two years and parts only during the third year. DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THIS LIMITED WARRANTY SHALL NOT APPLY: OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO...
Signal Words The signal words are intended to alert the viewer to the existence and the degree of hazard seriousness. White letters on Black letters on Black letters on This Safety Alert Symbol means: are used on the equipment safety signs. These words This signal word indicates a potentially hazardous situation which, if not avoided, will result in death or serious injury.
Page 9
SLOPE ANGLE GUIDE LOCATED INSIDE REAR COVER...
Page 10
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. This Act Seeks: OSHA Regulations Child Labor Under 16 Years Old...
SECTION I INTRODUCTION AND DESCRIPTION INTRODUCTION NOTE: All references made to right, left, front, rear, top or bottom is as viewed facing the direction of forward travel. DESCRIPTION...
OPERATION CAUTON If the operator is inexperienced with the zero turn mower lever steering/speed control, he/she should follow these recommendations: Disengage the mower blades. Go very slowly until thoroughly familiar with the machine. Keep away from fences, buildings, and other obstruc- tions.
Page 17
Grease caster wheel pivots ______________________________________________________every 50 hours Grease pusher bar pivots ________________________________________________________every 50 hours Change engine every 50 hours crankcase oil and filter ________________________________________________________ Change hydrostatic oil filter (See your Bush Hog Dealer) every 500 hours _____________________ Replace air filter element ____________________________________________________________annually or 500 hours...
Page 19
MOTION CONTROL LEVER ADJUSTMENT MOTION CONTROL STEERING ADJUSTMENT temporarily replace DRIVE ADJUSTMENTS CAUTION STOP THE ENGINE BEFORE MAKING ADJUSTMENTS. TEST DRIVE OPERATIONS...
STOP THE ENGINE, SET PARKING BRAKE, REMOVE IGNITION KEY AND SPARK PLUG WIRES FOR SAFETY. COUNTERBALANCE SPRING DECK BELT ADJUSTMENT USE ONLY GENUINE BUSH HOG REPLACEMENT PARTS length is 7-1/2” DECK SPINDLE BELT ROUTING DIAGRAM Front Of Deck WARNING TO AVOID SERIOUS BURN INJURIES:...
WARNING HIGH PRESSURE HYDRAULIC FLUID LEAKS CAN PENETRATE SKIN CAUSING SERIOUS INJURY AND GANGRENE. INJECTED FLUID MUST BE SURGICALLY REMOVED WITHIN A FEW HOURS BY A DOC- TOR FAMILIAR WITH THIS TYPE OF INJURY. TO AVOID SERIOUS INJURY FROM PRESSURE LEAKS: G USE CARDBOARD AND NOT HANDS TO SEARCH FOR LEAKS.
TROUBLESHOOTING CHECK LIST 1. ENGINE IDLES POORLY: 2. ENGINE BACKFIRES: 3. ENGINE RUNS BUT POWER UNIT WON’T MOVE FORWARD 4. POWER UNIT LOSES POWER OR HYDROSTAT SYSTEM OVERHEATS 5. ENGINE STALLS WHEN BLADES ARE ENGAGED ENGINE ELECTRICAL TROUBLE 1. ENGINE WILL NOT TURN OVER: 2.
To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information.
Page 27
WARNING TO AVOID SERIOUS INJURY OR DEATH DO NOT OPERATE MOWER WITHOUT DISCHARGE SHIELD OR DEFLECTOR IN PLACE AND GOOD REPAIR. TO AVOID SERIOUS INJURY OR DEATH, # READ OPERATOR’S MANUAL BEFORE OPERATING & FOLLOW ALL PRECAUTIONS. (CONTACT DEALER FOR MANUALS) # LOWER IMPLEMENT, STOP ENGINE AND REMOVE KEY BEFORE DISMOUNTING.
TORQUE SPECIFICATIONS AMERICAN METRIC *Use 75% of the specified torque value for plated fasteners. Use 85% of the specificed torque values for lubricated fasteners. BOLT DIAMETER WRENCH (IN.) “B” AND SIZE (IN.) “A” THREAD SIZE WRENCH BOLT SIZE DIA. (mm) “A” (mm) “B”...
Need help?
Do you have a question about the Commercial Series and is the answer not in the manual?
Questions and answers