Connecting To A Personal Computer; Connecting To A Player Or Computer With Hdmi; Connecting To A Computer With Displayport - NEC MultiSync C651Q User Manual

Connecting to a Personal Computer

The type of video connections that can be used to connect to a computer depends on the computer's display adapter.
The following table show the typical factory preset signal timing for each connection type. Some display cards may not be able
to support the required resolution for proper image reproduction with the selected connection.
The monitor will show the proper image by automatically adjusting the factory preset timing signal.
<Typical factory preset signal timing>
Scanning frequency
Resolution
Horizontal
640 x 480 31.5 kHz
800 x 600 37.9 kHz
1024 x 768 48.4 kHz
1280 x 720 45.0 kHz
1280 x 768 47.8 kHz
1280 x 800 49.7 kHz
1280 x 1024 64 kHz
1360 x 768 47.7 kHz
1366 x 768 47.7 kHz
1400 x 1050 65.3 kHz
1440 x 900 55.9 kHz
1600 x 1200 75.0 kHz
1680 x 1050 65.3 kHz
1920 x 1080 67.5 kHz
1920 x 1200 74.6 kHz
1920 x 2160 133.3 kHz
3840 x 2160 65.7 kHz
3840 x 2160 67.5 kHz
3840 x 2160 133.3 kHz
3840 x 2160 135.0 kHz
4096 x 2160* 54.0 kHz
3
4096 x 2160* 3 135.0 kHz
*1: Recommended resolution.
*2: Only HBR2 is set.
*3: Compressed image.

Connecting to a Player or Computer with HDMI

• Please use an HDMI cable with the HDMI logo.
• It may take a moment for the signal to appear after turning on the computer.
• Some display cards or drivers may not display an image correctly.
• When you use a computer with HDMI, please set OVER SCAN to "AUTO" or "OFF" as display drivers may not be fully
compatible and may not display an image correctly (see
• To output HDMI audio, set [HDMI1], [HDMI2] or [HDMI3] at AUDIO INPUT in the OSD or choose [HDMI1], [HDMI2] or
[HDMI3] by pressing the remote control AUDIO INPUT button.
• If the source signal is 3840 x 2160 (60 Hz) and 4096 x 2160 (60 Hz), please set MODE2 at HDMI in TERMINAL SETTINGS
(See page 38).
• If the monitor's main power is turned on after a connected computer is turned on, sometimes an image is not displayed.
In this case, please turn off the computer then turn it on again.

Connecting to a Computer with DisplayPort

• Please use a DisplayPort cable with the DisplayPort compliance logo.
• To use the DisplayPort out connector, please refer to Video out (See
• It may take a moment for the signal to appear after turning on the computer.
• When connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not appear.
• Some DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.
• To output DisplayPort audio, set [DisplayPort1] or [DisplayPort2] at AUDIO INPUT in the OSD or choose [DisplayPort1] or
[DisplayPort2] by the remote control AUDIO INPUT button.
• To display individual images at each connected monitors with the DisplayPort OUT connector, please set DisplayPort1.2 and
MST at DisplayPort in the TERMINAL SETTINGS (See
• If the monitor's main power is turned on after a connected computer is turned on, sometimes an image is not displayed.
In this case, please turn off the computer then turn it on again.
HDMI
Vertical MIDE1 MIDE2
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz No No
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz No No
60 Hz No No
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz Yes Yes
60 Hz Yes Yes
30 Hz No No
30 Hz Yes* 1 Yes
60 Hz No Yes
60 Hz No Yes*
1
24 Hz Yes Yes
60 Hz No Yes
English-18
DisplayPort
1.1a 1.2
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes* Yes
1
No No
No Yes* *
1, 2
No No
No No
No No
page 34).
page 68).
page 38).