Page 2
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
- Consult the dealer or an experienced radio/TV technician for help. is committed to making home CAUTION: Changes or modifications to this equipment not expressly approved by Toshiba could void the user·s authority to operate this CAUTION: TO REDUCE THE RISK OF ELECTRIC entertainment enjoyable and safe.
Page 6
If these sounds become frequent or continuous, Do not use this apparatus near water. store the TV in direct sunlight; hot, humid areas; unplug the power cord and contact a Toshiba Clean only with dry cloth. or areas subject to excessive dust or vibration.
Page 7
DVD and CD Software and/or the manufacture of DVD and CD discs, Toshiba cannot assure that the DVD player contained in this TV will successfully play every disc bearing the DVD and CD logos.
Page 8
Introduction Identification of controls (Continued) Remote control Inserting batteries The instructions in this manual describe the function on the remote control. See the page in for details. Open the battery compartment Install two “R03/AAA” batteries Replace the compartment cover in the direction of the (supplied), paying attention to cover.
Page 9
Your TV/DVD is capable of using ColorStream ® (component video). Connecting your TV/DVD to a component : Signal Á ow ® video compatible DVD player, such as a Toshiba DVD player with ColorStream can greatly enhance picture Camcorder (yellow) quality and performance.
Page 10
Cable Closed Caption >> Automatic Search Start Language English Video Label >> Auto Shut Off Aspect TOSHIBA Logo Light : Select : Adjust Reset >> : Select : Adjust - VHF/UHF channels Cable - Cable TV channels Press to select “Automatic Search”, then press or ENTER.
Page 11
Basic setup To memorize channels This TV/DVD is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the TV/DVD·s memory.
Page 12
New Password Password Language English ---- ---- Press EXIT/CANCEL to return to the normal Video Label >> screen. Auto Shut Off Aspect TOSHIBA Logo Light Reset >> : Select ENTER:Set [0-9] : Select ENTER:Set [0-9] : Select ENTER:Set Press to select an input which you...
Page 13
>> Password ---- Language English CC”. receiving a digital signal for the current station. Video Label >> Auto Shut Off Aspect TOSHIBA Logo Light Reset >> : Select ENTER:Set [0-9] : Select ENTER:Set Press to select “CC Setting”, then Press to select “V-Chip Set (DTV)”,...
Page 14
Blue, Yellow, Magenta, Cyan Auto Shut Off Film Mode Contrast Aspect Text Opacity: Auto, Solid, Transparent, PC Setting >> Sharpness TOSHIBA Logo Light Color Translucent, Flashing Reset >> Tint : Select ENTER:Set Background Auto, Black, White, Red, Green, Color Temperature...
Page 15
“HDMI” or “DVI”. Video Label >> Balance Auto Shut Off Stereo Aspect Surround Audio Audio Language English TOSHIBA Logo Light Reset >> HDMI1 Audio HDMI : Select : Adjust : Select ENTER:Set Speakers After your desired setting, press EXIT/CANCEL Press or Number buttons (0-6) to select to return to the normal screen.
Page 16
When you set the “TOSHIBA Logo Light” setting to “On”, the logo signal strength “TOSHIBA” on the front of the unit lights up. It is nice to change the mood of your room. Use this feature to turn the TV speakers off when you connect an audio...
Page 17
Basic playback EJECT Playing a disc (Continued) POWER To obtain a higher quality picture PAUSE Occasionally, some picture noise may appear on the TV screen while playing a PLAY DVD video disc because the high resolution pictures on these discs include a SKIP lot of information.
Page 18
Advanced playback Repeat playback/A-B Repeat playback Program playback/Random playback PLAY MODE 0–9 You can arrange the playback order of tracks on the disc. And the ENTER unit can also select tracks at random and playback them. These features work for Video CD. PLAY PLAY MODE For Audio CD and MP3/WMA CD, please see “Random playback...
Page 19
Use of CD-RW for MP3 À les is not recommended. You must obtain any required permission from copyright owners to download or use copyrighted content. Disc status To turn off the PBC Toshiba cannot and does not grant such permission. (see page 8) ® Audio CD/MP3/WMA/JPEG/DivX...
Page 20
Advanced playback ® MP3/WMA/JPEG/DivX and Audio CD Repeat, random and program playback operation (continued) using file browser / / / ENTER ENTER PLAY STOP SKIP PLAY DivX ® playback Playing DivX ® VOD content Repeat playback (Audio CD/ Random playback (Audio CD/ ®...
Page 21
Function setup Customizing the function settings (Continued) Setting details Section Option Details Page Parental E.B.L. Menu : Off : Off : Off : English Parental Menu TV Screen : Off : Off : English : 16:9 Menu QSound TV Screen Subtitle Set Password : On...
Page 22
Function setup Others EJECT Temporary cancel the rating level by DVD disc Understanding the Power Return feature 0–9 Depending on the DVD disc, the disc may try to temporarily cancel the rating level If the power is cut off while you are viewing the TV/DVD and the power is resupplied, the Power Return feature will that you have set.
Page 23
LCD TV/DVD Combination - Depot Repair Warranty be commenced to enforce any obligation of TACP Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original (1) For instructions on how to obtain warranty arising under the warranty or under any statute consumers in the United States.
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. A1-1 19LV610U...
Page 25
CAUTION THIS LCD COLOR TELEVISION EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CARE- FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Page 26
CAUTION THIS LCD COLOR TELEVISION EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CARE- FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL. A1-4 19LV610U/22LV610U/26LV610U...
18) Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit. A1-5 A1-5 19LV610U/22LV610U/26LV610U 19LV610U/22LV610U/26LV610U...
Page 29
24) Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume sound may cause hearing or speaker damage. A1-6 A1-6 19LV610U/22LV610U/26LV610U 19LV610U/22LV610U/26LV610U...
Page 30
If the liquid gets in your mouth, immediately gargle and consult with your doctor. Also, if the liquid gets in your eyes or touches your skin, consult with your doctor after rinsing for at least 15 minutes or longer in clean water. A1-7 A1-7 19LV610U/22LV610U/26LV610U 19LV610U/22LV610U/26LV610U...
• Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to keep the Flux smoke away from it. Circuit bridge points Pick Up PCB Fig.1 A1-8 19LV610U/22LV610U/26LV610U...
2. Set the DVD to the Stop Mode. 3. Press it in order of "SETUP", "SUBTITLE", "3", "AUDIO SELECT" and "0" key of a remote control unit. 4. The On Screen Display message " " will appear. 5. The Tray Lock has now been cleared. A1-9 19LV610U/22LV610U/26LV610U...
CD Power Power Source 120V, 60Hz Power Consumption at AC 38W at 120V 60Hz at DC Stand by (at AC) 0.8W at 120V 60Hz Energy Star Per Year -- kWh/Year Protector Power Fuse Safety Circuit IC Protector(Micro Fuse) A2-1 19LV610U...
Page 35
Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys 49 Keys Keys Power Eject Sleep TV/DVD Jump / - Display Subtitle Audio Select Input Select / Zoom Mute CH Up CH Down Vol Up Vol Down A2-2 19LV610U...
Page 36
Stable Sound Surround SRS WOW (SRS 3D/Focus/Tru Bass) Variable Audio Out Tuning CH Program Air/Cable ADD/DELETE Label CH Label Video Label Favorite CH V-Chip Type USA Type RRT Setup Lock Hotel Lock Channel Lock Video Lock Panel Lock A2-3 19LV610U...
Page 37
720×480p (4:3) Yes (60Hz) 720×480p (16:9) Yes (60Hz) 720×576i (4:3) 720×576i (16:9) 720×576p (4:3) 720×576p (16:9) 1280×720p Yes (60Hz) 1920×1080i Yes (60Hz) 1920×1080p Wall Mount Size W x H(mm) Yes (100 x 100) Screw Size M4 x 10 A2-4 19LV610U...
Page 38
Power (Tact) Channel Up/Menu Up/Play Channel Down/Menu Down/Stop Volume Up/Menu > Volume Down/Menu < Menu Play No (CH+ Alternative) Eject Skip+, Search+ Skip-, Search- Still/Pause Stop No (CH- Alternative) Main Power SW Input Select/Enter Rear Main Power SW A2-5 19LV610U...
Page 39
Container Stuffing (40' container) 1140 Sets/40' container w/Pallet w/Wrapping G-17 Material Cabinet Front PS 94V0 NON-DECABROM Rear PS 94V0 NON-DECABROM Jack Panel Non-Halogen Demand Eyelet Demand G-18 Environment Environmental standard requirement Green procurement of ORION Pb-free Phase3(Phase3A) Measures for Whisker A2-6 19LV610U...
Page 40
GENERAL SPECIFICATIONS LCD Size / Visual Size 21.60 inch / 547.7mmV System LCD Type Color TFT LCD Number of Pixels 1366(H) x 768(V) View Range Left/Right 85/85 degree Up/Down 80/80 degree < Bright Dot n = 0 Zero Bright Dot Ratio Color System NTSC Speaker...
Page 41
Timer Back-up (at Power Off Mode) more than G-10 Remote Unit RC-LT Control Glow in Dark Remocon Remocon Format TOSHIBA Format TOSHIBA Custom Code 40-BF h ,44-BB h ,45-BA h ,45-BC h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs...
Page 42
GENERAL SPECIFICATIONS Play Mode DVD Menu Down Left Right Enter Menu / Setup Exit / Cancel Game Picture Size Pause Play Stop Skip+ / Closed Caption Skip- / CH Return Search+ Search- Slow+ Slow- Angle Marker Top Menu Return Closed Caption Repeat A-B Zoom/ Quick View Freeze frame...
Page 43
GENERAL SPECIFICATIONS Lock Hotel Lock Channel Lock Video Lock Panel Lock Menu Language English French Spanish DBC (Dynamic Backlight Control) Signal Meter (DTV Signal) Brand Badge LED Closed Caption CC Advanced V-Chip Clear Picture Size HD Zoom Film Mode Aspect PFC(Power Factor circuit) Freeze frame PIP/POP...
Page 44
GENERAL SPECIFICATIONS Features Video CD Playback (DVD) SVCD Playback MP3 Playback Tray Lock JPEG Divx Playback DMF Support Digital Out (Dolby Digital) (MPEG) (PCM) (DTS) Down Mix Out (Dolby Digital) (DTS) Auto Retract Disc Closed Caption Screen Saver 4:3 (Letter Box, Pan Scan) TV Screen 16:9 (Wide) Audio DAC...
Page 45
GENERAL SPECIFICATIONS G-13 Interface Switch Side Power (Tact) Channel Up/Menu Up/Play Channel Down/Menu Down/Stop Volume Up/Menu > Volume Down/Menu < Menu Play No (CH+ Alternative) Eject Skip+, Search+ Skip-, Search- Still/Pause Stop No (CH- Alternative) Main Power SW Input Select/Enter Rear Main Power SW Indicator...
Page 46
GENERAL SPECIFICATIONS LCD Size / Visual Size 26.01 inch / 660.5mmV System LCD Type Color TFT LCD Number of Pixels 1366(H) x 768(V) View Range Left/Right 80/80 degree Up/Down 80/70 degree < Bright Dot n = 0 Zero Bright Dot Ratio Color System NTSC Speaker...
Page 47
Timer Back-up (at Power Off Mode) more than G-10 Remote Unit RC-LT Control Glow in Dark Remocon Remocon Format TOSHIBA Format TOSHIBA Custom Code 40-BF h ,44-BB h ,45-BA h ,45-BC h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs...
Page 48
GENERAL SPECIFICATIONS G-11 Features Auto Shut Off Auto Search Power On Memory Comb Filter Game Position Auto Setup(Language/CH Program) Picture Setting(TV) Picture Preference Brightness , Contrast , Color Tint Sharpness Color Temperature Backlight Picture Setting(PC) HOR Position , VER Position Phase, Clock Red, Green, Blue Auto Adjust...
Page 50
GENERAL SPECIFICATIONS G-12 Accessories Owner's Manual Language English w/Guarantee Card Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safeguard Dew/AHC Caution Sheet Quick Set-up Sheet(Spanish) Battery...
Page 51
GENERAL SPECIFICATIONS Terminals Rear Video Input 1 RCA x 1 Audio Input 1 RCA x 2(L/MONO, R) S - Input 1 Video Input 2 RCA x 1 Audio Input 2 RCA x 2(L/MONO, R) S - Input 2 Video Output Audio Output RCA x 2 (Variable) (L, R) Component Input 1...
(CP7001 and CP7002). 4. Unlock the support (2). 5. Remove the Cover AC in the direction of arrow (B). 6. Remove the 10 screws (3). Cover Inverter Cover AC LCD Panel CP7002 CP7001 Fig. 1-2 Back Cabinet Ass'y Fig. 1-3 19LV610U B1-1...
Page 53
Digital PCB smoke away from it. 5. When installing the DVD Deck, remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector. Back Cabinet Ass'y Fig. 1-6 19LV610U B1-2...
Page 54
2. Remove the Panel Side Ass'y in the direction of arrow (A). 3. Remove the 2 screws (2). 4. Remove the Operation PCB in the direction of arrow (B). Back Cabinet Ass'y Operation PCB Panel Side Ass'y Fig. 1-7 19LV610U B1-3...
Page 55
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: FRONT CABINET ASS'Y and LCD PANEL AND P.C. BOARDS (Refer to Fig. 1-3) 1. Turn up set and put the Front Cabinet Ass'y of LCD CAUTION on the top. Be careful not to remove the FFC cable forcibly, because 2.
Page 56
DISASSEMBLY INSTRUCTIONS 1-4: DVD MT PCB and DVD DECK (Refer to Fig. 1-4) 1-5: POWER PCB and REMOCON PCB (Refer to Fig. 1-5) 1. Put the Cabinet Back Ass'y on the bottom. 1. Remove the 7 screws (1). 2. Short circuit the position shown in Fig. 1-4 using a 2.
Page 57
DISASSEMBLY INSTRUCTIONS 1-7: OPERATION PCB (Refer to Fig. 1-7) 1. Push 9 supports (1). 2. Remove the Panel Side Ass'y in the direction of arrow (A). 3. Remove the 2 screws (2). 4. Remove the Operation PCB in the direction of arrow (B). Back Cabinet Ass'y Operation PCB Panel Side Ass'y...
Page 58
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: BACK CABINET ASS'Y (Refer to Fig. 1-3) AND P.C. BOARDS 1. Remove the 11 screws (1). 2. Remove the Back Cabinet Ass'y in the direction of arrow. CAUTION Be careful not to remove the FFC cable forcibly, because the FFC cable may be damaged.
Page 59
DISASSEMBLY INSTRUCTIONS 1-5: DVD MT PCB and DVD DECK (Refer to Fig. 1-5) 1-6: POWER PCB (Refer to Fig. 1-6) 1. Put the Cabinet Back Ass'y on the bottom. 1. Disconnect the following connector: (CP3902 and CP3903) 2. Short circuit the position shown in Fig. 1-5 using a 2.
Page 60
DISASSEMBLY INSTRUCTIONS 1-8: REMOCON PCB, LED PCB and OPERATION PCB (Refer to Fig. 1-8) 1. Disconnect the following connectors : (CP2201). 2. Unlock the support (1). 3. Remove the Remocon PCB in the direction of arrow (A). 4. Remove the 2 screws (2). 5.
Page 62
Fig. 2-3-B Switch PCB Ass'y • Install wire from (1) to (4) in order. Fig. 2-2-D Check Hook Traverse Ass'y Check Hook Check Hook Check Hook • Lossen the wire in the direction of the arrow. Fig. 2-2-E B2-2 19LV610U/22LV610U/26LV610U...
Shield Wire. (Refer to Fig. 3-4.) NOTE Blower type IC Do not move the Braided Shield Wire in the vertical desoldering machine direction towards the IC pattern. Braided Shield Wire Soldering Iron IC pattern Fig. 3-4 Fig. 3-2 B3-1 B3-1 19LV610U/22LV610U/26LV610U 19LV610U/22LV610U/26LV610U...
Page 64
Fig. 3-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 3-7.) NOTE Do not absorb the solder to excess. Soldering Iron Braided Shield Wire Fig. 3-7 B3-2 B3-2 19LV610U/22LV610U/26LV610U 19LV610U/22LV610U/26LV610U...
2 sec. (No disc) Refer to the "PARENTAL CONTROL - RATING LEVEL". Method Operations Press the following remocon keys continuously. The disk cannot be taken out. SETUP --->SUBTITLE ---> 3 ---> Refer to the "TRAY LOCK". AUDIO SELECT ---> 0 19LV610U/22LV610U/26LV610U...
Released times on the same date Laser drive time Release date (Example: 2008.12.16) DVD LD: 0Hour CD LD : 0Hour X=October Y=November Z=December When the changed version displays, the Re-write will be completed. 14. Turn off the power 19LV610U/22LV610U/26LV610U 19LV610U/22LV610U/26LV610U...
12. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. 13. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. 19LV610U 19LV610U...
Page 68
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0".
Page 69
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0".
6. Receive the DIGITAL broadcasting. color is achieved. 7. To display the adjustment screen fo DTV mode, select the digital channel. 8. Press the VOL.DOWN button on the set and the channel (9) on the remote control for more than 2 seconds. 19LV610U 19LV610U...
Page 71
31. Activate the adjustment mode display of Fig. 1-1 and press the channel button (51) on the remote control to select "CONTRAST MAX". 32. Press the LEFT/RIGHT button on the remote control until the contrast step No. becomes "145". 33. Check if the picture is normal. 19LV610U 19LV610U...
Page 72
Press the LEFT/RIGHT button on the remote control 32. Press the LEFT/RIGHT button on the remote control until the contrast step No. becomes "115". until the contrast step No. becomes "131". Check if the picture is normal. 33. Check if the picture is normal. 19LV610U 19LV610U...
Page 73
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE NO. FUNCTION NO. FUNCTION Read and perform these adjustments when repairing the 03 R DRIVE(N) 35 TINT circuits or replacing electrical parts or PCB assemblies. 04 R CUTOFF(N) 36 SHARP H1 MAX 05 G DRIVE(N) 37 SHARP H1 MIN CAUTION 06 G CUTOFF(N)
Page 74
ELECTRICAL ADJUSTMENTS 2-2: BRIGHTNESS CENT 2-3: CONTRAST MAX 1. Place the set in Aging Test for more than 15 minutes. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the color bar pattern. (RF Input) 2.
Page 75
ELECTRICAL ADJUSTMENTS 2-4: CONTRAST CENTER 2-5: CONTRAST 40 1. Place the set in Aging Test for more than 15 minutes. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the color bar pattern. (RF Input) 2.
Page 76
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE NO. FUNCTION NO. FUNCTION Read and perform these adjustments when repairing the 03 R DRIVE(N) 35 TINT circuits or replacing electrical parts or PCB assemblies. 04 R CUTOFF(N) 36 SHARP H1 MAX 05 G DRIVE(N) 37 SHARP H1 MIN CAUTION 06 G CUTOFF(N)
Page 77
ELECTRICAL ADJUSTMENTS 2-2: BRIGHTNESS CENT 2-3: CONTRAST MAX 1. Place the set in Aging Test for more than 15 minutes. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the color bar pattern. (RF Input) 2.
Page 78
ELECTRICAL ADJUSTMENTS 2-4: CONTRAST CENTER 2-5: CONTRAST 40 1. Place the set in Aging Test for more than 15 minutes. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the color bar pattern. (RF Input) 2.
Page 79
50 CONTRAST CENTER 51 CONTRAST MAX 52 CONTRAST MIN 53 COLOR CENTER 54 COLOR MAX 55 COLOR MIN 58 CONTRAST 40 NOTE: For the step no. with * mark, please adjust it according to the situation of the set. D-10 19LV610U D-11...
Page 80
ELECTRICAL ADJUSTMENTS 2-6: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment item is set correctly referring below. (TV/AV/GAME/COMPONENT/HDMI/PC/HDMI-DVI/DVD/PC/DTV) COMPONENT HDMI PC/HDMI-DVI FUNCTION GAME CVBS 480i 480p 720p 1080i 480i 480p 720p 1080i 1080p 640x480...
Page 81
ELECTRICAL ADJUSTMENTS 2-6: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment item is set correctly referring below. (TV/AV/GAME/COMPONENT/HDMI/PC/HDMI-DVI/DVD/PC/DTV) COMPONENT HDMI PC/HDMI-DVI FUNCTION GAME CVBS 480i 480p 720p 1080i 480i 480p 720p 1080i 1080p 640x480...
Page 82
CD2001 CP2301 DVD DECK DVD MT PCB REMOCON PCB CP7001 OS7601 OPERATION PCB CP2201 CP7002 CP2804 CD4201 CD3002 CP8101 TU5801 J501 CP4203 J4302 CP3601 J4206 CD6203 POWER PCB CD6201 SPEAKER DIGITAL PCB AC IN CD501 CP2001 LED PCB D-16 19LV610U...
TROUBLESHOOTING GUIDE (LCD SECTION) POWER DOES NOT TURN ON Is F501 broken? Change F501. Check IC501 and peripheral Is there voltage at pin circuit. 6 of IC501 21V? Change DIGITAL PCB. 19LV610U/22LV610U...
Page 86
TROUBLESHOOTING GUIDE POWER DOES NOT TURN ON Is F3801 broken? Change F3801. Check IC3802 and peripheral Is there voltage at circuit. pin 1 of IC3802 6V? Change R3836. Is R3836 broken? Check IC3801 and peripheral Is there voltage at pin circuit.
Page 87
Check IC301 and peripheral and 4 of IC301? circuit. Is there signal at pins Check Q3410,Q3411 and A3 and C4 of IC2801? peripheral circuit. Check IC2801 and peripheral Is there signal at pin 5 circuit. of TU5801? Change TU5801. 19LV610U/22LV610U...
Page 88
TROUBLESHOOTING GUIDE THE PICTURE APPEARS, BUT THE AUDIO DOES NOT APPEARS. (AT RF MODE) Is CP301 connected? Connect CP301. Is there signal at pins Change SP301 and SP302. 1 and 4 of CP301? Is there signal at pins 2 Check IC302 and peripheral and 5 of IC302? circuit.
Page 89
Is CD2801 connected? Connected CD2801 Is there voltage at pins Check Q3008 and 1, 2, 3, 16 and 17 of peripheral circuit. CP2804 5V? Is there signal at pins 7,9,10,12,13,22,23,25,26, Change V2801(PANEL). 28 of CP2804? Change DIGITAL PCB. 19LV610U...
Page 90
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR Is there voltage at CP7001, Check D515,T501 and CP7002,CP7003 and Does backlight shine? peripheral circuit. CP7004 24V? Is CD2801 connected? Connected CD2801 Is there voltage at pins Check Q3008 and 26,27,28,29 and 30 of peripheral circuit.
Page 91
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR Is there voltage at pins 1, Check IC3801, T3801, D3826 Does backlight shine? 2, 3, 4 and 5 of CP3906 and peripheral circuit. 24V? Is CD2801 connected? Connected CD2801. Is there voltage at pins Check Q3008 and 27, 28, 29 and 30 of peripheral circuit.
Page 92
TROUBLESHOOTING GUIDE THE COLOR DOES NOT APPEAR Is setting of color Adjust the color. normal? Is the color signal Receive the color signal. received? Check IC2801 and Is there color signal at peripheral circuit. IC2801? Change DIGITAL PCB. 19LV610U/22LV610U/26LV610U...
Page 93
Check the disc. logo picture? Does this have signal at Check pins 8 and 10 of pins 149 and 151 of CP8501 and peripheral circuit. IC4001? Does IC4001 gets P.CON+3.3V and Change IC4001. P.CON+1.8V? Check P.CON+3.3V and P.CON+1.8V line. 19LV610U/22LV610U/26LV610U...
Page 94
Does this eject disc at Check IC4001 and Does this have signal at change DVD DECK? peripheral circuit. pins 4 and 5 of CP2304? Change DVD DECK. Does this have signal at Change IC2301. pins 1 and 2 of CP2304? Change IC4001. E-10 19LV610U/22LV610U/26LV610U...
Page 95
Is the voltage between Does CD2001 connect Does this display JG017 and JG018 less with CP2301 correctly? "INCORRECT DISC"? than 0.3V? Connect CD2001. Does this display Change IC4001. reading mark? Change DVD DECK. Does disc rotate? Change IC4001. E-11 19LV610U/22LV610U/26LV610U...
Page 96
Is the voltage between Does CD2001 connect Does this display JG019 and JG018 less with CP2301 correctly? "INCORRECT DISC"? than 0.3V? Connect CD2001. Does this display Change IC4001. reading mark? Change DVD DECK. Does disc rotate? Change IC4001. E-12 19LV610U/22LV610U/26LV610U...
Page 97
Is CD8501 connected? Change DIGITAL PCB. NO SOUND DVD/CD DIGITAL AUDIO Does this have signal Change DIGITAL PCB. at pin1 of CP8501? Does this have signal Check line circuit IC4001 at pin122 of IC4001? to CP8501. Change IC4001. 19LV610U/22LV610U/26LV610U E-13...
Page 105
SW AUDIO L/R PC G AUDIO SW J8103 YUV AUDIO_L/R WD-00021-R IC6501 RCA-228H(3)NI-02 PC B TC74LVX4052FT HDMI AUDIO IN J4302 DVI AUDIO L/R PJ-364H DVD CP4205 DVD_SPDIF SPDIF DVD_R DVD_A_OUT_R DVD_L DVD_A_OUT_L DVD_Y Y VIDEO DVD_C C VIDEO STARTA_SW F-15 19LV610U F-16...
Page 106
SIGNAL (DIGITAL PCB) BLOCK DIAGRAM SPDIF_OUT COAXIAL OUT SPDIF SW J4206 IC6502 RCA-101HT(OR) TC7PA53FU SPEAKER L/R SPDIF SP301, SP302 S0308F01 S-VIDEO-IN AV1_Y J8101 AV1_C DIN-417HA-01 AMP L/R AV3_AV4_Y AUDIO L/R SOUND AMP IC IC301 COMPONENT_VIDEO_IN LA42052-E AV3_AV4_PB J8102 RCA-341H(NI)-09 AV3_AV4_PR DIGITAL RF (IF) TUNER ANALOG RF(CVBS)
Page 107
SIGNAL (DIGITAL PCB) BLOCK DIAGRAM COAXIAL OUT SPDIF SW SPDIF_OUT J4206 IC6502 RCA-101HT(OR) TC7PA53FU AUDIO OUT J4207 RCA-228H(NI)-01 SPEAKER L/R SPDIF SP301, SP302 S0412F06 AV1_Y S-VIDEO-IN J4202 AV1_C DIN-417HA-01 AMP L/R AUDIO L/R AV3/AV4_Y SOUND AMP IC IC302 COMPONENT IN AN17808B AV3/AV4_PB J4203...
Page 124
1K 1/16W RAMDQM RAMWE# RAMCLK (D_GND) RAMCKE PCB130 DMH104 NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. 19LV610U...
Page 127
B4008 EBMS160808A102_RDC45 FROM AUDIO/VIDEO RESET P.CON+3.3V_D D_GND PCB130 DMH104 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. 19LV610U...
Page 130
DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DURING PLAYBACK. DANS LA NOMENCLATURE DES PIECES H-13 19LV610U H-14...
Page 133
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DURING PLAYBACK. DANS LA NOMENCLATURE DES PIECES H-19 19LV610U H-20...
Page 136
DANGEREUSES AN POINT DE VUE SECURITE OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES H-25 19LV610U H-26...
Page 139
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-31 19LV610U H-32...
Page 142
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-37 19LV610U H-38...
Page 145
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES H-43 19LV610U H-44...
Page 148
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-49 19LV610U H-50...
Page 151
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-55 19LV610U H-56...
Page 153
SCALER POWER SCHEMATIC DIAGRAM (DIGITAL PCB) FROM REGULATOR SCALER IC IC2801 R8J66955BG FROM REGULATOR B2813 W840 VDD18HDMI A1.8V D1.25V HCB1608KF-121T20 VDD18HDMI D3.3V A3.3V VDD18HDMI A1.8V VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSHDMI B2814 VDD33HDMI VDD33HDMI HCB1608KF-121T20 VDD33HDMI VDD33IO AB22 VPPOTP VSSIO VSSIO TO HDMI...
Page 154
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST DANGEREUSES AN POINT DE VUE SECURITE DESCRIBED IN PARTS LIST ONLY WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES H-61 19LV610U H-62...
Page 157
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-67 19LV610U H-68...
Page 158
SCALER VIDEO/AUDIO SCHEMATIC DIAGRAM (DIGITAL PCB) SCALER IC2801 R8J66955BG FROM/TO JACK C2952 TU_CVBS PC_V VIN6A 0.1 B C2944 PC_H AV1_CVBS VIN5A 0.1 B AV3/AV4_Y AV1_CVBS C2943 AV1_Y VGA-G VIN4A 0.1 B VGA-B VGA-R C2938 AV1_C VIN4B AV3/AV4_PR 0.1 B SPDIF SSIN2 AV3/AV4_PB VIN2A...
Page 160
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-73 19LV610U H-74...
Page 163
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION: DIGITAL TRANSISTOR OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-79 19LV610U H-80...
Page 165
AV SWITCH SCHEMATIC DIAGRAM (DIGITAL PCB) FROM JACK2 AV1_A_IN_L AV1_A_IN_R AV2_A_IN_L AV2_A_IN_R FROM JACK DVI_A_IN_L DVI_A_IN_R DVD_L DVD_R B6503 D5.0V FCM1608KF-221T06 FROM MICON AV_SW1 AV_SW0 TO SCALER VIDEO/AUDIO NR6502 NR6501 NR6503 NR6504 CRA108223JV CRA108223JV CRA108223JV CRA108223JV SW_AUDIO_L SW_AUDIO_R AUDIO SW FROM REGULATOR IC6501 TC74LVX4052FT...
Page 166
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES H-85 19LV610U H-86...
Page 171
:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED N’UTILISER QUE DES FUSIBLE DE MEME TYPE 4A 125V (F501) WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-95 19LV610U H-96...
Page 176
DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE DES FUSIBLE DE MEME TYPE 4A 125V(F7001) DANS LA NOMENCLATURE DES PIECES WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. CAUTION :F7001 IS MANUFACTURED BY SKYGATE CO.,LTD., TYPE 20N. H-105 19LV610U H-106...
Page 177
BACKLIGHT INVERTER SCHEMATIC DIAGRAM IS_DET1 (POWER PCB) R7046 R7047 4A 125V FROM POWER IS_DET2 CP7001 F7001 R7042 4.7K C3502WR0-2P-HK INV+B HIGH VOLTAGE + 20N_4000FS C7024 C7023 4A 125V 0.0022 T7001 8137002R VS_DET1 R7043 4.7K C7025 C7026 CP7002 0.0022 12.0 C3502WR0-2P-HK VS_DET2 12.0 HIGH VOLTAGE +...
Page 178
DANGEREUSES AN POINT DE VUE SECURITE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DANS LA NOMENCLATURE DES PIECES H-109 19LV610U H-110...
Page 179
SOUND AMP SCHEMATIC DIAGRAM (POWER PCB) SOUND AMP IC IC301 LA42052-E Ripple OUT2 OUT1 Filter HEADPHONE JACK R308 10.3 14.0 J301 PJ-364H 1K 1/4W W846 R304 R306 W823 2.2K 2.2K R309 B308 FROM JACK OUT C303 R305 R307 HCB3216KF-391T20 1K 1/4W R310 B307 LOUT_SOUND...
Page 180
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. H-113 19LV610U H-114...
Page 181
JACK OUT SCHEMATIC DIAGRAM (POWER PCB) JACK_GND W860 FROM/TO JACK COMPONENT_VIDEO_IN J8102 (CP4301) RCA-341H(NI)-09 CP8101 127301123K2 LOUT_SOUND R8118_1 LOUT AV3_Y ROUT_SOUND R8119_1 ROUT AV3_PB AV1_C R8120_1 AV1_C AV3_PR (OPERATION PCB) AV1_Y AV1_Y FROM/TO SCALER AL2/YUV_A_IN_L YUV L IN (CD6202) CP2201 A2001WR2-3P R2201 R2202 AR2/YUV_A_IN_R...
Page 182
OPERATION/REMOCON SCHEMATIC DIAGRAM (REMOCON PCB) FROM/TO MICON OS2201 KSM-2003TC2P (CP6204) CP2201 A2001WV-5A Vout REMOCON IN R2208 AT+3.3V 47 1/16W STANDBY LED POWER ON LED STANDBY/POWER D2201 LTL-1BEFJ-002A PCBDA0 CEH443 (OPERATION PCB) TO MICON (CP6202) CP2202 A2001WR2-3P R2203 R2204 R2205 R2206 KEY-B KEY_B 15K 1/16W...
Page 183
LED SCHEMATIC DIAGRAM (LED PCB) FROM SCALER CP2001 (CD6201) A2001WR2-2P BADGE LED PCBDT0 CEH453 H-119 19LV610U/22LV610U/26LV610U H-120...
Page 184
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES H-121 19LV610U/22LV610U/26LV610U H-122...
Page 185
DANGEREUSES AN POINT DE VUE SECURITE THE TIME THIS INTERCONNECTION DIAGRAM IS THE LATEST AT NOTE: CRITICAL FOR SAFETY,USE ONES N’UTILISER QUE CELLS DECRITES OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES H-123 19LV610U H-124...
Page 186
INTERCONNECTION DIAGRAM CD4201 CP8501 CP8501 CP2301 CP8101 CP4301 SPDIF-134 DSM2(06SD) SPDIF-134 COMPONENT_VIDEO_IN LOUT LOUT J8102 ZERO ZERO Vref ROUT ROUT DVD_A_OUT_R DVD_A_OUT_R SLOT IN DVD CP7001 DRIVE HDMI AUDIO IN J4302 AV1_C AV1_C USB_UPDATE DVD_A_OUT_L DVD_A_OUT_L CP2803 CV_VTM101A DVD_RESET DVD RESET OPTICAL PICK-UP AV1_Y AV1_Y...
Page 188
SCALER VIDEO/AUDIO 10us 10us 0.2us 0.5V 100mV 200mV SOUND AMP 20us 10us 500mV 100mV 200mV 20us 500mV 100mV 200mV 500mV 100mV NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. 19LV610U/22LV610U...
MPEG/MICON/DSP/RF_AMP AUDIO/VIDEO 200ns 200μs 200mV 1.0V 10ns 200μs 500mV 1.0V 10nS 10μs 1.0V 200mV 500ns 10μs 1.0V 100mV MEMORY 10nS 1.0V The following waveforms were measured NOTE: at the point of the corresponding balloon number in the schematic diagram. 19LV610U/22LV610U...
WAVEFORMS FLASH 20ns 10us 0.2us 200mV 200mV 200mV TUNER SOUND 10us 10us 0.5V 100mV 200mV SCALER VIDEO/AUDIO 10us 10us 0.5V 100mV 200mV JACK2 20us 500mV 100mV 500mV 20us 500mV 100mV 500mV JACK 500mV 100mV 20us 500mV 100mV NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 191
WAVEFORMS MPEG/MICON/DSP/RF_AMP AUDIO/VIDEO 200ns 200μs 200mV 1.0V 10ns 200μs 500mV 1.0V 10nS 10μs 1.0V 200mV 500ns 10μs 1.0V 100mV MEMORY 10nS 1.0V The following waveforms were measured NOTE: at the point of the corresponding balloon number in the schematic diagram. 26LV610U...
Page 192
(POWER PCB ASS'Y) 101H 101D 104F 104D 101I 104E 101G 101H 101G 104E 104D 101G 101E 104D 101A 101I 104D 104C 101G 104B 101F 104A 101B Note: Hinge Ass'y (107) is not included in Stand Ass'y (104). 101C 19LV610U J1-2 J1-1...
If the repair is needed, replace the DVD MECHA ASS'Y. PCB640 (SW PCB ASS'Y) CD2301 Applying positions AA for the grease are displayed for this section. NOTE: CLASS MARK Check if the correct grease is applied for each position. GREASE J2-1 19LV610U/22LV610U/26LV610U...