Download Print this page

Advertisement

Quick Links

R-60 Audio Console
T
M
ECHNICAL
ANUAL
Oct 1998

Advertisement

loading
Need help?

Need help?

Do you have a question about the R-60 and is the answer not in the manual?

Questions and answers

Summary of Contents for AudioArts Engineering R-60

  • Page 1 R-60 Audio Console ECHNICAL ANUAL Oct 1998...
  • Page 2 R-60 Audio Console Technical Manual – 2nd Edition ® ©1998 Audioarts Engineering (a division of Wheatstone Corporation) AUDIOARTS ENGINEERING 600 Industrial Drive New Bern, North Carolina 28562 tel 252-638-7000 / fax 252-637-1285 R-60 / Oct 98...
  • Page 3: Hand Crimp Tool Wiring Instructions

    RIMP TOOL HAND CRIMP TOOL WIRING INSTRUCTIONS The supplied hand crimping tool (PALADIN model PA1645, W/S#850067) is used for all I/O wiring connections to and from the console. It is to be used with the supplied .062" pin diameter silver crimp terminals (figure 1) intended for 22 gauge wire.
  • Page 4 RIMP TOOL EXTRACTOR PIN INSTRUCTIONS If you should accidentally insert a crimp terminal pin into the wrong socket, the supplied pin extractor tool (Waldom P/N W-HT-2023) will let you correct your mistake without having to sacrifice a connector. STEP 1. Push wire attached to pin terminal, to be removed, forward to free pin terminal locking flanges from the...
  • Page 5 START, REMOTE STOP, and READY, along with +5 VOLTS, DIGITAL COM- MON, and MACHINE COMMON. The schematic diagram ("Typical IN-60 Remote Logic"; next page) shows typical connections for both mic and line inputs. R-60 / Nov 1994 R-60 / Nov 1994 R-60 / Nov 1994 R-60 / Nov 1994...
  • Page 6 O N N E C T I O N S O N N E C T I O N S Page 3 - 8 R-60 / Nov 1994 R-60 / Nov 1994 R-60 / Nov 1994 R-60 / Nov 1994...
  • Page 7 Key diagram showing back of typical 12-pin I/O connector connectors. Refer to the R-60 Mother board load sheet on page 7-2 for the plug, with pin numbers oriented exact location of specific connectors. Key drawing to left shows a typical as they would be seen while connector.
  • Page 8 (CT19-CT32, R-60 Mother Board load sheet dwg) Key diagram showing back of typical 12-pin I/O connector (CT7-CT12, R-60 Ext Mother Board load sheet dwg) plug, with pin numbers oriented Pin 1 - REMOTE ON as they would be seen while Pin 2 - REMOTE OFF wiring.
  • Page 9: Control Room

    Program/Audition Out Program/Audition Out Program/Audition Out Program/Audition Out Program/Audition Out (CT15, R-60 Mother Board load sheet dwg) Key diagram showing back of typical 12-pin I/O connector Pin 1 - LEFT PROGRAM OUTPUT, SHIELD plug, with pin numbers oriented Pin 2 - LEFT PROGRAM OUTPUT, LOW...
  • Page 10 Studio Control Studio Control Studio Control Studio Control Studio Control (CT17, R-60 Mother Board load sheet dwg) Key diagram showing back of typical 12-pin I/O connector Pin 1 - LEFT STUDIO OUTPUT, SHIELD plug, with pin numbers oriented Pin 2 - LEFT STUDIO OUTPUT, LOW...
  • Page 11 Pin 10 - LINE 3 RIGHT INPUT, SHIELD Pin 11 - LINE 3 RIGHT INPUT, LOW Pin 12 - LINE 3 RIGHT INPUT, HIGH Page 3 - 13 R-60 / Nov 1994 R-60 / Nov 1994 R-60 / Nov 1994 R-60 / Nov 1994...
  • Page 12 (CT1-CT14, R-60 Mother Board load sheet dwg)- selected to allow a wide range of oper- ating voltages, from 5 to 24 volts. For (CT1-CT6, R-60 Ext Mother Board load sheet dwg) this reason, the LEDs may appear dim SW 2 Pin 1 - SWITCH 1, LED CATHODE when operated from 5 volts.
  • Page 13 Tape Remote Switches 4-6 TA PE (CT19-CT32, R-60 Mother Board load sheet dwg)- SW 1 (CT7-CT12, R-60 Ext Mother Board load sheet dwg) Key diagram showing back of Pin 1 - SWITCH 4, LED CATHODE typical 12-pin I/O connector plug, with pin numbers oriented...
  • Page 14 OW OPTION OGIC FOLL OW OPTION The R-60 Logic Follow option allows line input modules to interface with two external source machines (tape players, cart machines, CD players, etc.), each at different location. The machine being controlled is determined by the A/B source select switch at the top of the module.
  • Page 15 R-60 EXT Mother Board Load Sheet...
  • Page 16 R-60 Mother Board Load Sheet...