Page 1 2006 Chevrolet Uplander Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-6 Safety Belts ... 1-21 Child Restraints ... 1-40 Airbag System ... 1-74 Restraint System Check ... 1-89 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division whenever it appears in this manual. Keep this manual in the vehicle, so it will be there if it is ever needed when you are on the road.
Page 3 Safety Warnings and Symbols There are a number of safety cautions in this book. We use a box and the word CAUTION to tell about things that could hurt you if you were to ignore the warning. CAUTION: These mean there is something that could hurt you or other people.
Page 4 Vehicle Damage Warnings Also, in this manual you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 5 These are some examples of symbols that may be found on the vehicle:...
Page 6 NOTES...
Page 7: Table Of Contents
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Six-Way Power Seats ...1-3 Heated Seats ...1-3 Reclining Seatbacks ...1-4 Head Restraints ...1-6 Rear Seats ...1-6 Rear Seat Operation ...1-6 Bucket Seats ...1-7 Captain Chairs ...1-14 Third Row Seat ...1-18 Safety Belts ...1-21 Safety Belts: They Are for Everyone ...1-21 Questions and Answers About Safety Belts ...1-25 How to Wear Safety Belts Properly ...1-26...
Page 8: Front Seats
Front Seats Manual Seats Use the lever located on the front of the seat to adjust the seat forward or rearward. Pull up on the lever to unlock the seat. Slide the seat to where you want it and release the lever. CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle...
Page 9: Six-Way Power Seats
Six-Way Power Seats Your vehicle may have this feature. If it does, the six-way power seat control is located on the outboard side of the driver’s seat. Your vehicle may also have a passenger’s six-way power seat. • Move the front of the control up or down to adjust the front portion of the seat up or down.
Page 10: Reclining Seatbacks
Reclining Seatbacks To adjust a seatback, pull up on the lever located on the outboard side of the driver’s or front passenger’s seats. Release the lever to lock the seatback where you want it. Push and pull on the seat to make sure it is locked into position.
Page 11 Do not have a seatback reclined if your vehicle is moving. CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 12: Rear Seats
Head Restraints Adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash. The head restraints are adjustable on the ﬁrst and second row seats.
Page 13: Bucket Seats
Bucket Seats Your vehicle may have bucket seats in the second row. These seats can be adjusted several different ways. Fold and Tumble Feature The second row bucket seats can be folded and tumbled forward. Use this feature for exiting and entering third row seats, if the vehicle has them.
Page 14 3. Pull the nylon strap, located on the rear right hand side of the seat, or lift the recline lever, located on the front right hand side of the seatback, to raise the seatback to the upright position. CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash.
Page 15 The other lever is located on the rear of the seat. To adjust the second row bucket seats forward or rearward, do the following: 1. Lift up either lever and slide the seat forward or rearward. 2. Release the lever when the seat is in the desired position.
Page 16: Removing The Bucket Seats
CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked. To raise the seatback to the upright position from a reclined position, do the following: 1.
Page 17 4. Release the rear set of hooks from the ﬂoor pins by pulling either the nylon strap, located at the base of the seat, or the release handle located on the side of the seat. Use the strap to guide the seat forward.
Page 18 Reinstalling the Bucket Seats CAUTION: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After installing the seat, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Page 19 3. Firmly push the rear seat hooks into the rear ﬂoor pins by pushing down the rear of the seat. CAUTION: A seat that is not locked into place properly can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to lock the seat into place properly when installing it.
Page 20: Captain Chairs
Captain Chairs Your vehicle may have second row captain chairs. If so, they can be adjusted forward or rearward and the seatbacks can be adjusted. Adjusting the Captain Chairs Forward and Rearward There are two manual adjustment bars on each seat. One is located under the front of the seat cushion.
Page 21 Removing a Captain Chair (without a Side Impact Airbag) If your vehicle has captain chairs with side impact airbags, the seats cannot be removed. See Where Are the Airbags? on page 1-76 for more information. To remove a captain chair, do the following: 2.
Page 22 Installing a Captain Chair (without a Side Impact Airbag) CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked.
Page 23 To install a captain chair, do the following: 1. Hook the front latches over the front ﬂoor pins. 2. Push the rear of the seat down to lock the rear latches onto the rear set of ﬂoor pins. 3. Push and pull on the seat to be sure it is properly attached.
Page 24: Third Row Seat
Third Row Seat Your vehicle may have a third row seat. It is a full bench seat and may come with the convenience center. See Convenience Center on page 2-53 for more information. The third row seat can be removed and replaced, or with the seatback folded, it will lie ﬂat with the convenience center.
Page 25 Removing the Third Row Seat 1. Remove the convenience center, if equipped. See Convenience Center on page 2-53 for more information. 2. Make sure all items are off the seat. 3. Put the seatback in its folded position before removing the seat. See “Folding the Seatback(s)” earlier in this section.
Page 26 Installing the Third Row Seat CAUTION: A seat that is not locked into place properly can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to lock the seat into place properly when installing it.
Page 27: Safety Belts
3. Try to raise the seat to make sure that it is locked down. The indicator pins will no longer stick out when the seat is properly latched into place. CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash.
Page 28: Why Safety Belts Work
CAUTION: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 29 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-23...
Page 30 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-24...
Page 31: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Will I be trapped in the vehicle after an accident...
Page 32: Driver Position
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt.
Page 33 4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 1-39. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 34 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. 1-28 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 35 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 36 What is wrong with this? The belt is over an armrest. 1-30 CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt.
Page 37 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 38 What is wrong with this? The belt is twisted across the body. 1-32 CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 39: Shoulder Belt Height Adjustment
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 40: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 41 Lap-Shoulder Belt All rear seat positions have lap-shoulder belts. Here is how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
Page 42 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 43: Rear Safety Belt Comfort Guides
Rear Safety Belt Comfort Guides Rear safety belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the belt away from the neck and head.
Page 44 3. Be sure that the belt is not twisted and it lies ﬂat. The guide must be on top of the belt. CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Page 45: Safety Belt Pretensioners
4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-34. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
Page 46: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. 1-40 What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 47 CAUTION: Never do this. Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. 1-41...
Page 48 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? If the child is sitting in a seat next to a window, move the child toward the center of the vehicle.
Page 49: Infants And Young Children
Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs. This applies belt force to the child’s pelvic bones in a crash. Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children.
Page 50 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 51 CAUTION: Newborn infants need complete support, including support for the head and neck. This is necessary because a newborn infant’s neck is weak and its head weighs so much compared with the rest of its body. In a crash, an infant in a rear-facing seat settles into the restraint, so the crash forces can be distributed across the strongest part of an infant’s body, the back and...
Page 52: Child Restraint Systems
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous ﬂat surface. Make sure that the infant’s head rests toward the center of the vehicle.
Page 53 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness.
Page 54 How Should I Use a Child Restraint? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Page 55 When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
Page 56: Where To Put The Restraint
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General Motors recommends that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 57 If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat the unless passenger airbag status indicator shows off. Never put a rear facing child restraint in the right front passenger seat unless the airbag is off.
Page 58: Lower Anchors And Tethers For Children (Latch)
Lower Anchors and Tethers for Children (LATCH) Your vehicle has the LATCH system. The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system Make sure that a LATCH-compatible child restraint...
Page 59 Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Page 60 Lower Anchor and Top Tether Anchor Locations Seating positions with top tether anchors. (Lower Anchor): Seating positions with two lower anchors. Second Row Seating positions with top tether anchors. Third Row 1-54 (Top Tether Anchor): For the second row seating positions, the top tether anchors are located on the seatback, near the base of each seat.
Page 61 Second Row For the center third row position, if equipped, the top tether anchor is located on the seatback, near the center of the third row seating position. This anchor can accommodate only one top tether. Third Row Do not secure a child restraint in the right front passenger’s position or in the third row outboard positions, if equipped, if a national or local law requires that the top tether be attached, or if the instructions...
Page 62 Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchors, or use the vehicle’s safety belts to secure the restraint,...
Page 63 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2.
Page 64: Securing A Child Restraint In A Rear Seat Position
Securing a Child Restraint in a Rear Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-52. For vehicles with a third row, there are no top tether anchors in the outboard seating positions.
Page 65 5. To tighten the belt, push down on the child restraint, 4. Pull the rest of the shoulder belt all the way out of pull the shoulder portion of the belt to tighten the lap the retractor to set the lock. portion of the belt and feed the shoulder belt back into the retractor.
Page 66: Securing A Child Restraint In The Right Front Seat Position
6. If your child restraint has a top tether, and the position that you are using has a top tether anchor, attach and tighten the top tether to the top tether anchor. Refer to the instructions that came with the child restraint and to Lower Anchors and Tethers for Children (LATCH) on page 1-52.
Page 67 passenger seat the unless passenger airbag status indicator shows off. Never put a rear facing child restraint in the right front passenger seat unless the airbag is off. Here is why: CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates.
Page 68 You will be using the lap-shoulder belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. 1.
Page 69 5. Pull the rest of the shoulder belt all the way out of 6. To tighten the belt, push down on the child restraint, the retractor to set the lock. pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 70: Built-In Child Restraint
7. Push and pull the child restraint in different directions to be sure it is secure. 8. If the airbag or airbags are off, the off indicator on the instrument panel will be lit and stay lit when the key is turned to RUN or START. If a child restraint has been installed and the on indicator is lit, turn the vehicle off.
Page 71 Use only with children who weigh between 22 and 40 pounds (10 and 18 kg) and whose height is between 33.5 and 40 inches (850 and 1 016 mm). Use only with children whose shoulders are below the shoulder belt slots for the harness system and who are capable of sitting upright alone.
Page 72 Securing a Child in the Built-In Child Restraint 1. Raise the head restraint until the lower edge of the head restraint is even with the top of the seatback. 1-66 2. Rotate the head restraint rearward until it touches the top of the seatback. Make sure there is no gap between the lower edge of the head restraint and the top of the seatback.
Page 73 3. Lower the child restraint cushion. You will be using the child restraint’s harness (A) to secure your child. Do not use the vehicle’s safety belts. CAUTION: Using the vehicle’s regular safety belts on a child seated on the built-in child restraint cushion can cause serious injury to the child in a sudden stop or crash.
Page 74 WARNING: FAILURE TO FOLLOW THE MANUFACTURER’S INSTRUCTIONS ON THE USE OF THIS CHILD RESTRAINT SYSTEM CAN RESULT IN YOUR CHILD STRIKING THE VEHICLE’S INTERIOR DURING A SUDDEN STOP OR CRASH. SNUGLY ADJUST THE BELTS PROVIDED WITH THIS CHILD RESTRAINT AROUND YOUR CHILD. 4.
Page 75 10. Pull up on the latch plates to make sure they 11. Now fasten the left and right halves of the shoulder are secure. harness clip together. The clip can be easily pulled apart and is designed to pull apart during a collision. 1-69...
Page 76 CAUTION: A built-in child restraint harness that is not properly adjusted can cause injury to the child in a sudden stop or collision. A harness that is loose, twisted, worn improperly or improperly fastened will not be able to restrain the child’s upper body.
Page 77 13. Adjust the position of the harness on the child’s shoulder by moving the clip along the harness until it is level with the child’s armpits. On each side of the harness, the shoulder part should be centered on the child’s shoulder. The harness should be away from the child’s face and neck, but not falling from the child’s shoulders.
Page 78 2. Unlatch the harness by pushing the button on the buckle. 3. Move one side of the harness off the child’s shoulder. 4. Move the other side of the harness off the child’s shoulder. 5. Remove the child from the child restraint cushion. 1-72 Storing the Built-In Child Restraint Always properly store the built-in child restraint before...
Page 79 2. Fold the child restraint cushion and leg rest up into the seatback. 3. Press the child restraint cushion ﬁrmly into the seatback. 4. Then press the leg rest ﬁrmly into the seatback, and secure it by pressing the upper corners against the fastener strips on the seatback.
Page 80: Airbag System
5. Rotate the head restraint forward and push it all the way down. Just like the other restraint systems in your vehicle, your built-in child restraint needs to be periodically checked and may need to have parts replaced after a crash. See Checking the Restraint Systems on page 1-89 and Replacing Restraint System Parts After a Crash on page 1-90.
Page 81 CAUTION: (Continued) from it. Airbags are “supplemental restraints” to the safety belts. Airbags are designed to work with safety belts but do not replace them. Frontal airbags for the driver and right front passenger are designed to deploy in moderate to severe frontal and near frontal crashes.
Page 82: Where Are The Airbags
CAUTION: Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 83 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. If your vehicle has a side impact airbag for the driver, it is in the side of the driver’s seatback closest to the door. 1-77...
Page 84 If your vehicle has a side impact airbag for the right front passenger and/or the second row captain’s chairs (if equipped), it is in the side of the seatback closest to the door. 1-78 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 85: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? The driver’s and right front passenger’s frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes. But they are designed to inﬂate only if the impact exceeds a predetermined deployment threshold. Deployment thresholds take into account a variety of desired deployment and non-deployment events and are used to predict how severe a crash is likely to be in time for the airbags to inﬂate and help...
Page 86: What Makes An Airbag Inﬂate
In any particular crash, no one can say whether an airbag should have inﬂated simply because of the damage to a vehicle or because of what the repair costs were. For frontal airbags, inﬂation is determined by what the vehicle hits, the angle of the impact, and how quickly the vehicle slows down.
Page 87: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After the airbag inﬂates, it quickly deﬂates, so quickly that some people may not even realize the airbag inﬂated. Some components of the airbag module may be hot for a short time. These components include the steering wheel hub for the driver’s frontal airbag and the instrument panel for the right front passenger’s frontal airbag.
Page 88: Passenger Sensing System
In many crashes severe enough to inﬂate an airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for your airbag system.
Page 89 The passenger sensing system works with sensors that are part of the right front passenger’s seat and safety belt. The sensors are designed to detect the presence of a properly-seated occupant and determine if the passenger’s airbag or airbags should be enabled (may inﬂate) or not.
Page 90 If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat the unless passenger airbag status indicator shows off. Never put a rear facing child restraint in the right front passenger seat unless the airbag is off.
Page 91 • the system determines that a small child is present in a booster seat • a right front passenger takes his/her weight off of the seat for a period of time • the right front passenger seat is occupied by a smaller person, such as a child who has outgrown child restraints •...
Page 92 For some children who have outgrown child restraints and for very small adults, the passenger sensing system may or may not turn off the right front passenger’s airbag or airbags, depending upon the person’s seating posture and body build. Everyone in your vehicle who has outgrown child restraints should wear a safety belt properly —...
Page 93 CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the frontal airbag.
Page 94: Servicing Your Airbag-Equipped Vehicle
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the airbag system. To purchase a service manual, see Service Publications Ordering Information on page 7-15.
Page 95: Restraint System Check
Because I have a disability, I have to get my vehicle modiﬁed. How can I ﬁnd out whether this will affect my airbag system? Changing or moving any parts of the front seats, safety belts, the airbag sensing and diagnostic module (located under the driver’s seat), or the instrument panel can affect the operation of the airbag system.
Page 96: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 97: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry System ...2-4 Remote Keyless Entry System Operation ...2-5 Doors and Locks ...2-10 Door Locks ...2-10 Power Door Locks ...2-11 Delayed Locking ...2-12 Automatic Door Lock ...2-12 Programmable Automatic Door Unlock ...2-13 Lockout Protection ...2-13 Dual Sliding Doors ...2-13 Power Sliding Door (PSD) ...2-16 Liftgate ...2-22...
Page 98 Section 2 Storage Areas ...2-48 Glove Box ...2-48 Cupholder(s) ...2-48 Overhead Console (With Rail) ...2-49 Overhead Console (Without Rail) ...2-50 Floor Console Storage Area ...2-50 Folding Tray ...2-50 Second Row Center Console ...2-51 Features and Controls Luggage Carrier ...2-52 Convenience Net (With Rear Convenience Center) ...2-52 Convenience Net (Without Rear Convenience Center) ...2-53...
Page 99: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed.
Page 100: Remote Keyless Entry System
® Any new PASS-Key III key must be programmed before it will start your vehicle. See PASS-Key page 2-28 for more information on programming your new key. Notice: If you ever lock your keys in your vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys.
Page 101: Remote Keyless Entry System Operation
Remote Keyless Entry System Operation You can lock and unlock the vehicle’s doors and the liftgate using the remote keyless entry transmitter supplied with your vehicle. The remote keyless entry transmitter shown here is for a vehicle equipped with the remote vehicle start feature and dual power sliding doors.
Page 102: Remote Power Sliding Door Operation
When you use your remote keyless entry transmitter to unlock your vehicle the turn signal lamps will ﬂash to let you know the command was received. (Remote Alarm): When you press the horn button on the remote keyless entry transmitter, the turn signal lamps will ﬂash and the horn will sound.
Page 103: Battery Replacement
Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer.
Page 104: Remote Vehicle Start
Remote Vehicle Start This feature allows you to start the engine from outside the vehicle. It may also turn the rear window defogger if the outside temperature is below 45°F (7°C). Laws in some local communities may restrict the use of remote starters.
Page 105 After two remote starts have been provided, the vehicle’s ignition switch must be turned to RUN and then back to LOCK using the key before the remote start procedure can be used again. If you enter the vehicle after a remote start, and the engine is running, insert the key into the ignition switch and turn it to the RUN position to drive the vehicle.
Page 106: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 107: Power Door Locks
From the inside, use the manual or power door locks. To unlock either front door from the inside, pull back on the manual lever. To lock either front door from the inside, push the manual lever forward. Power Door Locks Your vehicle has power door locks.
Page 108: Delayed Locking
Delayed Locking This feature allows the locking of the vehicle to be delayed until all doors have been closed for approximately ﬁve seconds. To activate the delayed locking feature, do one of the following: • Press the driver’s door power lock switch one time while the driver’s door is open.
Page 109: Programmable Automatic Door Unlock
Programmable Automatic Door Unlock Your vehicle was programmed so that all doors will unlock automatically when the shift lever is moved into PARK (P). To change the way the automatic door unlocking operates, see DIC Vehicle Personalization (Uplevel Only) on page 3-69. Lockout Protection The lockout protection feature makes it more difficult to lock the key in the vehicle.
Page 110: Sliding Door Lock
Sliding Door Lock 2-14 CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut be sure to hold it open until everyone is clear of the door, and only then allow it to slowly close.
Page 111: Sliding Door Security Lock
Lock either sliding door from inside the vehicle by moving the manual lever down. Unlock it by moving the lever up. With the power door locks, the sliding door lock has a delay feature. See Delayed Locking on page 2-12 and DIC Vehicle Personalization (Uplevel Only) on page 3-69.
Page 112: Power Sliding Door (Psd)
If you want to open the sliding door while the security lock is on, unlock and open the door from the outside. You should let adults and older children know how the security lock works, and how to cancel the lock. If you do not, adults or older children who ride in the rear will not be able to open the sliding door from the inside while the security lock feature is in use.
Page 113 Power Sliding Door (PSD) Switches Your vehicle will have one of the following switch(es) located on the overhead console switchbank. If your vehicle has a single power sliding door (PSD), you have this switch. PSD Activation/Override (Deactivation) Switch If your vehicle has dual power sliding doors, you have these switches.
Page 114 Your vehicle also has passenger power sliding door activation switch(es). If you have a single PSD, this switch is located in front of the passenger side sliding door. If your vehicle has dual PSDs, the switches are located in front of both sliding doors. Passenger PSD Activation Switch Power Sliding Door Operation...
Page 115 If the power sliding door has been manually locked, you must unlock the PSD before it can be opened. Notice: If you leave the power sliding door on when you go through an automatic car wash, the door may accidentally open. Be sure the power sliding door is turned off when going through a car wash.
Page 116 The driver’s side sliding door is designed to open only a little if the fuel door is open. If this ever happens, do not try to force the sliding door. When the fuel ﬁller door is closed, the driver’s side sliding door can be opened normally.
Page 117: Resetting The Power Sliding Door
CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut, turn on the power sliding door feature.
Page 118: Liftgate
If any of these conditions occur, the power sliding door may need to be reset. If your vehicle has the dual power sliding doors, both doors will have to be reset. To reset a door, do the following: 1. Check to be sure the power sliding door is unlocked and securely closed.
Page 119 CAUTION: It can be dangerous to drive with the liftgate open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate:...
Page 120: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 121: Power Windows
Power Windows The switches on the driver’s door armrest control the front windows when the ignition is in RUN, ACCESSORY or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-31. The driver’s power window switch has two down positions.
Page 122: Power Rear Quarter Windows
Power Rear Quarter Windows Your vehicle may have power rear quarter windows. This switch, located in the overhead console switchbank, is used for opening and closing the power rear quarter windows. Press the top of the switch to open the windows; both windows will open.
Page 123: Content Theft-Deterrent
Content Theft-Deterrent Your vehicle may have a theft-deterrent alarm system. A light located on top of your instrument panel, near the center of the vehicle next to the windshield, will ﬂash slowly to let you know that the system has been armed. While armed, the doors will not unlock with the power door lock switch.
Page 124: Arming With Your Key
Arming with Your Key Your alarm system will arm when you use your key to lock the driver’s door. The security light will ﬂash to let you know the system is arming. After all doors and the liftgate are closed and locked, the security light will begin ﬂashing at a very slow rate to let you know the system is armed.
Page 125: Pass-Key ® Iii
Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. ® PASS-Key III uses a radio frequency transponder in the key that matches a decoder in your vehicle. ® PASS-Key III Operation Your vehicle is equipped with the PASS-Key...
Page 126: Starting And Operating Your Vehicle
To program the new key, do the following: 1. Verify the new key has PK3 stamped on it. 2. Insert the original, already programmed key into the ignition lock cylinder and start the engine. If the engine will not start, see your dealer for service. 3.
Page 127: Ignition Positions
Ignition Positions The key can be turned to one of four positions while in the ignition switch. A (LOCK): This is the only position from which you can remove the key. This position locks your ignition and transaxle. Notice: Using a tool to force the key from the ignition switch could cause damage or break the key.
Page 128: Starting The Engine
Starting the Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle.
Page 129: Engine Coolant Heater
Engine Coolant Heater Your vehicle may have an engine coolant heater. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 130: Automatic Transaxle Operation
Automatic Transaxle Operation Maximum engine speed is limited when the vehicle is in PARK (P) or NEUTRAL (N), to protect driveline components from improper operation. There are several different positions for the shift lever. PARK (P): This gear position locks the front wheels. It is the best position to use when you start the engine because your vehicle cannot move easily.
Page 131 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped.
Page 132 Warm-Up Shift Your vehicle has a computer controlled transaxle designed to warm up the engine faster when the outside temperature is 35°F (2°C) or colder. You may notice that the transaxle will shift at a higher vehicle speed until the engine is warmed up. This is a normal condition designed to provide heat to the passenger compartment and defrost the windows more quickly.
Page 133: Parking Brake
Parking Brake The parking brake is located under the instrument panel on the driver’s side of the vehicle. To set the parking brake, hold the regular brake pedal down with your right foot and push down on the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on.
Page 134: Shifting Into Park (P)
Shifting Into Park (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 135: Shifting Out Of Park (P)
Torque Lock If you are parking on a hill and you do not shift your vehicle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P).
Page 136: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • Your exhaust system sounds strange or different.
Page 137: Mirrors
CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly.
Page 138: Outside Convex Mirror
Outside Convex Mirror CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.
Page 139 Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstar.ca. ® OnStar Services For new vehicles equipped with OnStar Sound Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections Plan to meet your needs.
Page 140: Universal Home Remote System
Universal Home Remote System The Universal Home Remote System, a combined universal transmitter and receiver, provides a way to replace up to three hand held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems, and home lighting.
Page 141: Universal Home Remote System Operation
Universal Home Remote System Operation Do not use the Universal Home Remote with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your Universal Home Remote...
Page 142 3. Simultaneously press and hold both the desired Universal Home Remote button and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming”...
Page 143: Gate Operator And Canadian Programming
Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner.
Page 144: Storage Areas
Reprogramming a Single Universal Home Remote Button To program a device to Universal Home Remote using a Universal Home Remote button previously trained, follow these steps: 1. Press and hold the desired Universal Home Remote button. Do not release the button. 2.
Page 145: Overhead Console (With Rail)
Overhead Console (With Rail) If your vehicle is equipped with an overhead console, it may contain the following: • Reading lamps. See Front Reading Lamps on page 3-18 or Rear Reading Lamps on page 3-19. • Switchbank. See Overhead Console Switchbank on page 3-20.
Page 146: Overhead Console (Without Rail)
4. Firmly press down making sure the latch is ﬂat with the ribs (A) on the storage bin. 5. Switch hands and repeat Steps 2 through 4 for the latch on the opposite side of the storage bin. 6. Reverse these steps in order to remove the storage bin.
Page 147: Second Row Center Console
Second Row Center Console If your vehicle has the second row center console, use the following procedure to remove or install the console. Removing the Center Console 1. Locate the attachment lever in an opening on the rear of the console 2.
Page 148: Luggage Carrier
Luggage Carrier CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along.
Page 149: Convenience Net
Convenience Net (Without Rear Convenience Center) Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, like grocery bags, from falling over. Install the convenience net at the rear of your vehicle, inside the liftgate.
Page 150: Removing The Convenience Center
Removing the Convenience Center 1. Make sure that all items are off the convenience center and that it is empty. 2. Turn the hand knob, located at the rear of the convenience center, counterclockwise until the knob is loose. 3. Lift up on the hand knob, then grip and pull up on the convenience center to remove it from the vehicle.
Page 151 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-8 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-9 Windshield Wipers ...3-9 Windshield Washer ...3-9 Rear Window Wiper/Washer ...3-10 Cruise Control ...3-10 Exterior Lamps ...3-14...
Page 152 Section 3 Engine Coolant Temperature Gage ...3-40 Malfunction Indicator Lamp ...3-41 Oil Pressure Light ...3-44 Security Light ...3-45 Cruise Control Light ...3-45 Highbeam On Light ...3-45 Fuel Gage ...3-45 Low Fuel Warning Light ...3-46 Driver Information Center (DIC) ...3-46 DIC Operation and Displays ...3-47 DIC Warnings and Messages ...3-53 DIC Vehicle Personalization (Uplevel Only) ...3-69 Instrument Panel...
Page 153 NOTES...
Page 154: Instrument Panel Overview
Instrument Panel Overview...
Page 155 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-27. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 3-114. D.
Page 156: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located in the center of the instrument panel.
Page 157: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane Change Signals. See Turn and Lane-Change Signals on page 3-8. • Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. •...
Page 158: Turn And Lane-Change Signals
Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically.
Page 159: Flash-To-Pass
Flash-to-Pass When the headlamps are off, pull the lever toward you to momentarily turn on the high beams. This will signal that you are going to pass. When you release the lever, they will turn off. Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it.
Page 160: Rear Window Wiper/Washer
Rear Window Wiper/Washer CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. The controls for the rear window washer/wiper are located on the end of the turn signal/multifunction lever.
Page 161 The cruise control lever is located below the windshield wiper control on the right side of the steering wheel. RES + (Resume/Accelerate): Push the lever up to resume the cruise control speed, or to accelerate when passing another vehicle. ON/OFF : Press the button on the end of the lever to turn the cruise control on.
Page 162 Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 163 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Push up on the cruise control lever toward the plus (resume/accelerate) position, then release the lever and take your foot off the accelerator pedal.
Page 164: Exterior Lamps
Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle’s speed, its load, and the steepness of the hills. When going up steep hills, the accelerator pedal might have to be used in order to maintain the vehicle’s speed.
Page 165: Headlamps On Reminder
Due to the momentary switch design, your automatic lights may be disabled even if the control is in the AUTO position. (Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: • Taillamps •...
Page 166: Instrument Panel Brightness
A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered. The DRL system will make front parking and turn signal lamps come on in daylight when the following conditions are met: •...
Page 167: Interior Lamps Control
Interior Lamps Control The interior lamp control is located to the right of the exterior lamp controls on the instrument panel to the left of the steering column. (Interior Lamp Override): Turn the outer knob to this position to have your interior lamps remain off while any door is open.
Page 168: Delayed Lighting
The interior lamps may stay on for up to 25 seconds after all doors have been closed if they have not been locked. See Delayed Lighting on page 3-18. To turn the entry lighting feature off or on, see DIC Vehicle Personalization (Uplevel Only) on page 3-69.
Page 169: Rear Reading Lamps
Rear Reading Lamps There are two reading lamps in the third row headliner. To turn either reading lamp on or off, press the lens of the lamp. There may also be a reading lamp in the second row, integrated with the dome lamp. To turn the second row reading lamp on or off, press the button next to the lamp lens.
Page 170: Overhead Console Switchbank
Overhead Console Switchbank The overhead console switchbank is located in the overhead console. This switchbank may include the following: • Power Sliding Door(s)/Override Switch(es). See Power Sliding Door (PSD) on page 2-16. • Power Rear Quarter Windows. See Power Rear Quarter Windows on page 2-26.
Page 171: How The System Works
CAUTION: Even with the Ultrasonic Rear Park Assist system, the driver must check carefully before backing up. The system does not operate above typical backing speeds of 3 mph (5 km/h) while parking. And, the system does not detect objects that are more than 5 feet (1.5 meters) behind the vehicle.
Page 172: Accessory Power Outlet(S)
If an object is detected at a REVERSE (R) speed of less than 3 mph (5 km/h), one of the following will occur: Description English amber light amber/amber lights 40 in amber/amber/red lights & 20 in continuous chime amber/amber/red lights ﬂashing &...
Page 173: Power Outlet 115 Volt Alternating Current
Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses.
Page 174: Cigarette Lighter
The power outlet is not designed for the following electrical equipment and may not work properly if these items are plugged into the power outlet: • Equipment with high initial peak wattage such as: compressor-driven refrigerators and electric power tools. •...
Page 175 (Bi-Level): This mode directs half of the air to the instrument panel outlets, then directs the remaining air to the ﬂoor outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. (Floor): This mode directs most of the air to the ﬂoor outlets.
Page 176: Rear Window Defogger
Recirculation: This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly. This mode will automatically be selected when you select maximum air conditioning.
Page 177: Outlet Adjustment
Outlet Adjustment (Open): Turn the thumbwheel to this position to open the air outlets. (Closed): Turn the thumbwheel to this position to close the air outlets. Use the louvers located on the air outlets to change the direction of the airﬂow. Operation Tips •...
Page 178 Your vehicle may also have a rear climate control system that allows the rear passengers to adjust the temperature and fan speed for the rear seating area. When the front climate control is in AUX and the rear climate control fan or temperature button is pressed, the display will show the same airﬂow modes as the front climate control system.
Page 179: Passenger Compartment Air Filter
Rear Air Outlets The outlet behind the left rear seat is the cold air return outlet. Be sure to keep it free from obstructions. Also, keep the area around the base of the center instrument panel console, between and under the front seats, free of objects that could also obstruct airﬂow to the rear seating area.
Page 180 2. Then push the tab, located on the left of the inner access panel, to the right. 3. The ﬁrst air ﬁlter will pull straight out. To remove the second, reach in and slide it toward the opening. Pull the second ﬁlter out. 3-30 4.
Page 181: Warning Lights, Gages, And Indicators
Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 182: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically. The indicator warning lights and gages are explained on the following pages.
Page 183: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper-resistant odometer.
Page 184: Passenger Safety Belt Reminder Light
Passenger Safety Belt Reminder Light Several seconds after the key is turned to RUN or START, a chime will be provided for several seconds to remind the front passenger to buckle their safety belt. This would only occur if a passenger is detected by the passenger sensing system.
Page 185: Passenger Airbag Status Indicator
CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your...
Page 186 If the word ON or the on symbol is lit on the passenger passenger’s airbag or airbags are enabled (may inﬂate). CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag and seat-mounted side impact airbag (if equipped).
Page 187 Here is why: CAUTION: Even though the passenger sensing system is designed to turn off the passenger’s frontal airbag and side impact airbag (if equipped) if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off.
Page 188: Charging System Light
Charging System Light The charging system light will come on brieﬂy when you turn on the ignition, but the engine is not running, as a check to show you it is working. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system.
Page 189: Anti-Lock Brake System Warning Light
If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service.
Page 190: Traction Control System (Tcs) Warning Light
Traction Control System (TCS) Warning Light Your vehicle is equipped with a traction control system warning light. The traction control system warning light may come on for the following reasons: • If you turn the system off by pressing the traction control button.
Page 191: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
Page 192: If The Light Is Flashing
If the Light is Flashing The following may prevent more serious damage to your vehicle: • Reducing vehicle speed • Avoiding hard accelerations • Avoiding steep uphill grades • If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady”...
Page 193 Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration.
Page 194: Oil Pressure Light
Oil Pressure Light If you have low engine oil pressure, this light will stay on after you start your engine, or come on when you are driving. This indicates that your engine is not receiving enough oil. The engine could be low on oil, or could have some other oil problem.
Page 195: Security Light
Security Light For information regarding this light, see Theft-Deterrent Systems on page 2-26. Cruise Control Light This light comes on whenever you set your cruise control. The light will go out when the cruise control is turned off. See Cruise Control on page 3-10 for more information.
Page 196: Low Fuel Warning Light
Your fuel gage tells you about how much fuel you have left when the ignition is on. Here are four things some owners ask about. All these things are normal and do not indicate that anything is wrong with the fuel gage. •...
Page 197: Dic Operation And Displays
If equipped, the outside air temperature automatically appears in the bottom right corner of the DIC display when viewing all of the information screens, except for the oil life screens. If the outside air temperature is at or below 37°F (3°C), the temperature reading will toggle between displaying the outside temperature and the word ICE for two minutes.
Page 198 Information Button Items (Information): Press this button to scroll through the following items: Odometer Press the information button until the odometer displays. This mode shows the distance the vehicle has been driven in either miles or kilometers. Trip A and Trip B Press the information button until A or B displays.
Page 199 Once TIME ELAPSED :00 is displayed, press the set/reset button to start the timing feature. Press the set/reset button again to stop it. If you will be starting and stopping your vehicle, during a trip for instance, the TIME ELAPSED feature will automatically start timing where it left off when you last stopped.
Page 200: Oil Life
Instantaneous Fuel Economy Press the information button until INST ECONOMY displays. This mode shows the current fuel economy at a particular moment and will change frequently as driving conditions change. This mode shows the instantaneous fuel economy in miles per gallon (mpg) or liters per 100 kilometers (L/100 km).
Page 201 Menu Button Items (Menu): Press this button to scroll through the following items: Units Press the menu button until UNITS displays. This mode allows you to select between English or Metric units of measurement. Once in this mode, press the set/reset button to select between ENGLISH or METRIC.
Page 202 Compass Calibration (Uplevel Only) Under certain circumstances, such as during a long distance cross-country trip, it will be necessary to compensate for compass variance and reset the zone through the DIC. Compass variance is the difference between the earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, the compass in the vehicle could give false readings.
Page 203: Dic Warnings And Messages
6. Drive the vehicle slowly in a circle two times to activate the compass. When the calibration is complete, the DIC will display CALIBRATION FINISHED. 7. If the message CAL appears in the DIC, you must manually put the compass into the calibration mode again.
Page 204: Battery Saver Active
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 205: Check Gas Cap
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 206: Engine Coolant Hot
This message will appear and a chime will sound when the ignition is off. This message cannot be acknowledged. DRIVER’S DOOR AJAR This message will display when the driver’s door is not closed properly. When this message appears, you should make sure that the driver’s door is closed completely.
Page 207: Headlamps Suggested
To avoid added strain on the engine, turn off the air conditioner if it is on. When the coolant temperature returns to normal, the air conditioner can be turned back on. This message will display only when the ignition is in RUN.
Page 208: Key In Ignition
KEY FOB BATTERY LOW This message will display when the battery in the remote keyless entry transmitter needs to be replaced. To replace the battery, see “Battery Replacement” under Remote Keyless Entry System Operation on page 2-5. This message will display while the ignition is in RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
Page 209 This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 210: Low Fuel
LOW FUEL This message will display when your vehicle is low on fuel. You should reﬁll the tank as soon as possible. See Fuel Gage on page 3-45 and Filling the Tank on page 5-8 for more information. The message will display and a chime will sound while the ignition is in RUN.
Page 211 This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 212: Reduced Engine Power
PASSENGER SEATBELT IS NOT FASTENED This message reminds you to buckle the passenger’s seat belt. This message will display and a chime will sound when the ignition is on, the driver’s seat belt is buckled, the passenger’s seat belt is unbuckled with the passenger airbag enabled and the vehicle is in motion.
Page 213 REMOTE START DISABLED This warning message will come on if a remote start attempt is unsuccessful. This may be caused if any of the following conditions are true when a remote start attempt is made: • The remote start system is disabled through the DIC.
Page 214: Right Rear Turn Lamp Out
RIGHT REAR TURN LAMP OUT This message will display when the right rear turn signal bulb needs to be replaced. See Taillamps, Turn Signal, Stoplamps and Back-up Lamps on page 5-47. This message will display while the ignition is in RUN.
Page 215: Service Brake System
SERVICE BRAKE SYSTEM This message will display when a problem with the brake system has been detected. Have your vehicle serviced by your GM dealer as soon as possible. The brake system warning light will also appear on the instrument panel cluster when this message appears on the DIC.
Page 216: Service Traction System
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 217: Stability Control Active
STABILITY CONTROL ACTIVE ® If your vehicle has StabiliTrak , this message will ® display when StabiliTrak is actively assisting you with directional control of the vehicle. Slippery road conditions may exist when this message is displayed, so adjust your driving accordingly. See StabiliTrak System on page 4-9.
Page 218: Traction Control Off
TRACTION CONTROL OFF If your vehicle has the traction control system, this message will display when the traction control system turns off. See Traction Control System (TCS) on page 4-8 for more information. This message will only display while the ignition is in RUN and will disappear after two seconds.
Page 219: Dic Vehicle Personalization (Uplevel Only)
DIC Vehicle Personalization (Uplevel Only) Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. The customization features include the following: •...
Page 220 Entering the Personal Program Menu 1. Turn the ignition on and place the vehicle in PARK (P). 2. Press the menu button until PERSONAL PROGRAM displays. If the vehicle is not in PARK (P), PERSONAL PROGRAM ONLY IN PARK will display. If the vehicle is not able to enter the personal program menu, PERSONAL PROGRAM NOT AVAILABLE will display.
Page 221 ALL KEYS RESET This screen will only display if YES was selected on the FACTORY DEFAULTS screen. Press the set/reset button to scroll through the following choices: CANCEL (default): The features will not be set to their factory default settings and the DIC will return to the FACTORY DEFAULTS screen.
Page 222 DELAYED LOCKING This feature allows the locking of the vehicle to be delayed until all of the doors have been closed for approximately ﬁve seconds. When the delayed locking feature is enabled, it may be activated when the key is out of the ignition by doing one of the following: •...
Page 223 CONTENT THEFT If your vehicle has the content theft-deterrent system, once this feature is turned on, the system will activate if someone tries to enter the vehicle without using the remote keyless entry transmitter or the correct key. It will also activate when an incorrect key is used in the ignition.
Page 224 REMOTE START If your vehicle has remote start, this feature allows the remote start to be turned OFF or ON. The remote start feature allows you to start the engine from outside of the vehicle using the remote keyless entry transmitter.
Page 225 Press the menu button until PERSONALIZE KEY appears on the DIC display. Press the set/reset button to scroll through the following choices: NO (default): The key will not be personalized. YES: The key will be personalized. Choose one of the available settings and press the menu button while it is displayed on the DIC to select it and move on to the next feature.
Page 226 ALL (default): All of the doors will unlock when the vehicle is shifted into PARK (P) or the key is taken out of the ignition. Choose one of the available settings and press the menu button while it is displayed on the DIC to select it and move on to the next feature.
Page 227: Audio System(S)
Exiting the Personal Program Menu The personal program menu will be exited when any of the following occurs: • The vehicle is shifted out of PARK (P). • The vehicle is no longer in RUN. • The end of the personal program menu is reached. Audio System(s) Determine which radio your vehicle has and then read the pages following to familiarize yourself with its...
Page 228: Setting The Time
Here are some ways in which you can help avoid distraction while driving. While your vehicle is parked: • Familiarize yourself with all of its controls. • Familiarize yourself with its operation. • Set up your audio system by presetting your favorite radio stations, setting the tone, and adjusting the speakers.
Page 229: Radio With Cd
Radio with CD Radio with CD shown, Radio with Six-Disc CD similar Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: •...
Page 230: Playing The Radio
XM™ Satellite Radio Service If your vehicle has XM™, XM™ is a satellite radio service that is based in the 48 contiguous United States and in Canada (if available). XM™ offers over 100 coast-to-coast channels including music, news, sports, talk, and children’s programming. XM™ provides digital quality audio and text information that includes song title and artist name.
Page 231: Finding A Station
Finding a Station BAND: Press this button to switch between FM1, FM2, AM, or XM1 or XM2 (if equipped). The display will show the selection. (Tune): Turn this knob to select radio stations. SEEK : Press the right or the left arrow to go to the next or to the previous station and stay there.
Page 232: Setting The Tone (Bass/Treble)
Setting the Tone (Bass/Treble) (Bass/Treble/Midrange): Press this knob to select BASS, MIDRANGE, or TREBLE. Turn the knob to increase or to decrease. If a station is weak or noisy, decrease the treble. To adjust the bass, midrange, and treble to the middle position, press and hold this knob when the tone control is on the display.
Page 233: Rds And Xm
Finding a Category Station (RDS and XM™) To select and ﬁnd a desired category perform the following: 1. Press the CAT button. The last selected category will appear on the display. 2. Turn the tune knob to select the category. 3.
Page 234: Rds Messages
RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display. You will hear the announcement, even if the volume is low or a CD is playing. If a CD is playing, play will stop during the announcement.
Page 235: Radio Messages
Radio Messages CAL ERR (Calibration Error): The audio system has been calibrated for your vehicle from the factory. If CAL ERR appears on the display, it means that the radio has not been conﬁgured properly for your vehicle and must be returned to your GM dealer for service. Radio Display Message XL (Explicit Language...
Page 236 Radio Display Message CH Off Air Channel not in service CH Unavail Channel no longer available No Info Artist Name/Feature not available No Info Song/Program Title not available No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category...
Page 237 Radio Display Message Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Chk XMRcvr Hardware failure Playing a CD (Single CD Player) Insert a CD partway into the slot, label side up. The player will pull it in and the CD should begin playing.
Page 238 Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen instead. Notice: If you add any label to a CD, insert more than one CD into the slot at a time, or attempt to play scratched or damaged CDs, you could...
Page 239: Playing A Cd(S) (Six-Disc Cd Player)
Playing a CD(s) (Six-Disc CD Player) If the ignition or radio is turned off, with a CD in the player, it will stay in the player. When the ignition or radio is turned on, the CD will start playing where it stopped, if it was the last selected audio source.
Page 240 To insert multiple CDs, do the following: 1. Turn the ignition on. 2. Press and hold the load button for two seconds. You will hear a beep and LOAD ALL DISC will appear on the display. 3. When INSERT CD # appears on the display, load a CD.
Page 241 (Reverse): Press and hold this button to reverse within the current track. (Fast Forward): Press and hold this button to fast forward through the current track. RDM (Random): Press this button to hear the tracks in random, rather than sequential order, on one CD or all of the loaded CDs.
Page 242: Mp3 Format
CD AUX (Auxiliary): Press this button to play a CD when listening to the radio. CD will appear on the display when a CD is in the player. If your system is equipped with a remote playback device, pressing this button a second time will allow the remote device to play.
Page 243 Empty Directory or Folder If a root directory or a folder exists somewhere in the ﬁle structure that contains only folders/subfolders and no compressed ﬁles directly beneath them, the player will advance to the next folder in the ﬁle structure that contains compressed audio ﬁles and the empty folder will not be displayed or numbered.
Page 244 File System and Naming The song name that will be displayed will be the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio will display the ﬁle name without the extension (such as .mp3) as the track name.
Page 245 If an error appears on the display, see “CD Messages” later in this section. (Tune): Turn this knob to go to the next or previous track. (Previous Folder): Press this button to go to the ﬁrst track in the previous folder. Press and hold this button to reverse through the current track.
Page 246 BAND: Press this button to listen to the radio when a CD is playing. The inactive CD will remain safely inside the radio for future listening. CD AUX (Auxiliary): Press this button to play a CD when listening to the radio. The CD symbol will appear on the display when a CD is loaded.
Page 247 To delete the entire song list, perform the following steps: 1. Turn the CD player on. 2. Press the song list button to turn song list on. S-LIST will appear on the display. 3. Press and hold the song list button for more than four seconds.
Page 248: Rear Seat Entertainment System
Rear Seat Entertainment System Your vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system includes a DVD player, a video display screen, auxiliary inputs, two sets of wireless headphones (if included), and a remote control. Parental Control (Parental Control): This button is located behind the video screen, below the auxiliary jacks.
Page 249 The headphones will shut off automatically to save the battery power if the RSE system is shut off or if the headphones are out of range of the transmitters for more than three minutes. The transmitters are located next to the DVD faceplate. If you move too far forward or step out of the vehicle, the headphones will lose the audio signal.
Page 250: Stereo Rca Jacks
Wired Headphones There is a right and left wired headphone jack. To adjust the volume, do the following: 1. Plug the headphone into the corresponding jack, located behind the video screen, next to the auxiliary jacks. 2. Press the corresponding headphone button on the DVD faceplate.
Page 251 To use the auxiliary audio and video inputs, connect an external auxiliary device such as a camcorder to the RCA jacks and turn on both the auxiliary device power and the power on the front of the RSE player. If a disc is present when the RSE power is turned on, the player will automatically begin playing the disc and the user will need to press the AUX button on the remote control or on the DVD player faceplate to switch...
Page 252: Dvd Player
Video Screen The video screen is located in the overhead console. To use the video screen, do the following: 1. Push forward on the release button and the screen will fold down. 2. Adjust its position as desired. When the video screen is not in use, push it up into its stowed and latched position.
Page 253: Playing A Disc
DVD Player Buttons (Stop/Eject): Press and release this button to stop playing, rewinding, or fast forwarding. Press this button twice to eject a disc. If the player is already stopped, then only press this button once. (Power): Press this button to turn the DVD player on and off.
Page 254: Remote Control
Some DVDs will not allow fast forwarding or skipping of the copyright information or previews. Some DVDs will begin playing after the previews have ﬁnished. If the DVD does not begin playing at the main title, refer to the on-screen instructions. Stopping and Resuming Playback To stop playing a disc, press and release the stop button on the DVD player faceplate or the remote...
Page 255: Remote Control Buttons
Remote Control Buttons (Power): Press this button to turn the DVD player on and off. (Backlight): Press this button to turn the remote control backlighting on. The backlight will automatically turn off after eight seconds. (Title): Press this button to display the current title number.
Page 256 (Play/Pause): Press this button to start play of a disc. Press this button while a disc is playing to pause it. Press it again to continue playing the disc. (Prior Chapter/Track): Press this button to go to the beginning of the current chapter or track. Press this button again to return to the previous chapter or track.
Page 257 RSE On-Screen Display (OSD) Menu To use the RSE OSD menu when using a DVD or an auxiliary device, do the following: To access this menu, press the display button on the remote control. Once the menu is on the screen, use the directional arrows and the enter button to navigate the screen.
Page 258 Tips and Troubleshooting Chart Problem Recommended Action No power. The ignition may not be in ACCESSORY, RUN, or RAP. Disc will not play. The system might be off. The parental control button might have been pressed. The power indicator lights will ﬂash.
Page 259 Problem Recommended Action The remote control does Point the remote control not work. directly at the face of the DVD unit. The batteries could be weak or put in wrong. The parental control button might have been pressed, the power indicator lights will ﬂash.
Page 260: Dvd Messages
Problem Recommended Action DVD System inoperable. In severe or extreme temperatures the DVD system might not be operable. Temperatures below 4°F ( 20°C) or above 140°F (60°C) could damage the DVD system. Operate the DVD system under normal or comfortable cabin temperature ranges.
Page 261: Rear Seat Audio (Rsa)
DVD Distortion There may be an experience with video distortion when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It may be necessary to turn off the DVD player when operating one of these devices in or near the vehicle. ®...
Page 262 The remote control will not operate any of the RSA features. (Power): Press this button to turn the RSA system on or off. RSA CHB or RSA CH2 will appear on the display when the system is on to indicate the channel to receive audio for the wireless headphones.
Page 263: Theft-Deterrent Feature
When a CD is playing in the single CD player, press this button to select the next track. This function is inactive if the front seat passengers are listening to a CD. When a CD is playing in the six-disc CD changer, press this button to select the next CD, if multiple CDs are loaded.
Page 264: Audio Steering Wheel Controls
Audio Steering Wheel Controls If your vehicle has this feature, some audio controls can be adjusted at the steering wheel. They include the following: wt u x (Seek): Press the up or the down arrow to go to the next or previous station and stay there. To scan stations, press and hold either arrow for two seconds until FREQUENCY SCAN appears on the display.
Page 265: Radio Reception
Radio Reception You may experience frequency interference and static during normal radio reception if items such as cellphone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. The range for most AM stations is greater than for FM, especially at night.
Page 266: Care Of The Cd And Dvd Player
Care of the CD and DVD Player The use of CD lens cleaners for CDs is not advised, due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD mechanism. Fixed Mast Antenna The ﬁxed mast antenna can withstand most car washes without being damaged.
Page 267: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunken Driving ...4-3 Control of a Vehicle ...4-5 Braking ...4-5 Anti-Lock Brake System (ABS) ...4-6 Braking in Emergencies ...4-8 Traction Control System (TCS) ...4-8 ® StabiliTrak System ...4-9 All-Wheel Drive (AWD) System ...4-11 Steering ...4-11 Off-Road Recovery ...4-14...
Page 268: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-21. CAUTION: Defensive driving really means “Be ready for anything.”...
Page 269: Drunken Driving
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: •...
Page 270 It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
Page 271: Control Of A Vehicle
There is something else about drinking and driving that many people do not know. Medical research shows that alcohol in a person’s system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking —...
Page 272: Anti-Lock Brake System (Abs)
coordination, and eyesight all play a part. So do alcohol, drugs, and frustration. But even in three-fourths of a second, a vehicle moving at 60 mph (100 km/h) travels 66 feet (20 m). That could be a lot of distance in an emergency, so keeping enough space between your vehicle and others is important.
Page 273 Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel.
Page 274: Braking In Emergencies
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 275: Stabilitrak ® System
When this warning message is on, the TRACTION CONTROL OFF message in the DIC will come on to remind you that the system will not limit wheel spin. Adjust your driving accordingly. The traction control system automatically comes on whenever you start your vehicle. To limit wheel spin, especially in slippery road conditions, you should always leave the system on.
Page 276: Traction Control Operation
If either message appears on the DIC, and your vehicle has not gone through hard acceleration, braking or multiple turns in the ﬁrst two miles of driving, your vehicle should be taken in for service. The STABILITY CONTROL ACTIVE message will appear on the DIC only when the system is both on and activated.
Page 277: Power Steering
In the limited mode, the traction control system will only use engine traction-control and is limited in its ability to provide optimal performance since the system will not utilize brake traction-control to control slip on the drive wheels. The system will return to normal operation after the brakes have cooled.
Page 278: Steering Tips
Steering Tips It is important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here is why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves. The traction of the tires against the road surface makes it possible for the vehicle to change its path when you turn the front wheels.
Page 279: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 280: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you are driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 281: Loss Of Control
• Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Page 282 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to your vehicle’s three control systems.
Page 283: Driving At Night
Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving. •...
Page 284: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you cannot stop, accelerate, or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Page 285: Driving Through Flowing Water
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Page 286: City Driving
Some Other Rainy Weather Tips • Turn on your low-beam headlamps — not just your parking lamps — to help make you more visible to others. • Besides slowing down, allow some extra following distance. And be especially careful when you pass another vehicle.
Page 287: Freeway Driving
Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip.
Page 288: Before Leaving On A Long Trip
At the entrance, there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic. Try to determine where you expect to blend with the ﬂow.
Page 289: Highway Hypnosis
Here are some things you can check before a trip: • Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside? • Wiper Blades: Are they in good shape? • Fuel, Engine Oil, Other Fluids: Have you checked all levels? •...
Page 290: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or mountains is different from driving in ﬂat or rolling terrain. If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable.
Page 291: Winter Driving
• Know how to go down hills. The most important thing to know is this: let your engine do some of the slowing down. Shift to a lower gear when you go down a steep or long hill. • Know how to go uphill. You may want to shift down to a lower gear.
Page 292: Driving On Snow Or Ice
Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning triangles. And, if you will be driving under severe conditions, include a small bag of sand, a piece of old carpet, or a couple of burlap bags to help provide traction.
Page 293: If You Are Caught In A Blizzard
If you have a traction system, it will improve your ability to accelerate when driving on a slippery road. But you can turn the traction system off if you ever need to. You should turn the traction system off if your vehicle ever gets stuck in sand, mud, ice, or snow.
Page 294 • Put on extra clothing or wrap a blanket around you. If you do not have blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, ﬂoor mats — anything you can wrap around yourself or tuck under your clothing to keep warm. You can run the engine to keep warm, but be careful.
Page 295: If Your Vehicle Is Stuck In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 296: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If your vehicle has traction control, you should turn your traction control system off. See Traction Control System (TCS) on page 4-8 and StabiliTrak page 4-9.
Page 297 Tire and Loading Information Label Example Label A vehicle speciﬁc Tire and Loading Information label is attached to the center pillar (B-pillar) of your vehicle. With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The tire and loading information label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Page 298 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, the load from your trailer will be transferred to your vehicle.
Page 299 Example 2 Item Description Vehicle Capacity Weight for Example 2 Subtract Occupant Weight 150 lbs (68 kg) Available Cargo Weight Total Item 1,000 lbs (453 kg) 750 lbs (340 kg) 250 lbs (113 kg) Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions.
Page 300 Certiﬁcation/Tire Label A vehicle speciﬁc Certiﬁcation/Tire label is attached to the rear edge of the driver’s door. The label shows the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo.
Page 301: Towing
If you put things inside your vehicle — like suitcases, tools, packages, or anything else, they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or...
Page 302: Dolly Towing
• How far will you tow? Some vehicles have restrictions on how far and how long they can tow. • Do you have the proper towing equipment? See your dealer or trailering professional for additional advice and equipment recommendations. • Is your vehicle ready to be towed? Just as you would prepare your vehicle for a long trip, you’ll want to make sure your vehicle is prepared to be...
Page 303: Level Control
Level Control On vehicles equipped with automatic level control, the rear of the vehicle is automatically kept level as you load or unload your vehicle. However, you should still not exceed the GVWR or the GAWR. See Loading Your Vehicle on page 4-30. You may hear the compressor operating when you load or unload your vehicle, and periodically as the system self-adjusts.
Page 304: If You Do Decide To Pull A Trailer
Successful, safe trailering takes correct equipment, and it has to be used properly. That is the reason for this section. In it are many time-tested, important trailering tips and safety rules. Many of these are important for your safety and that of your passengers.
Page 305: Weight Of The Trailer
Weight of the Trailer How heavy can a trailer safely be? It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature, and how much your vehicle is used to pull a trailer are all important. It can also depend on any special equipment that you have on your vehicle, and the amount of tongue weight the vehicle can carry.
Page 306: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 307 You can expect tongue weight to be at least 10 percent of trailer weight (850 lbs (386 kg)) and because the weight is applied well behind the rear axle, the effect on the rear axle will be greater than just the weight itself, as much as 1.5 times as much.
Page 308: Safety Chains
It is important that you make sure your vehicle does not exceed any of its ratings — GCWR, GVWR, RGAWR, Maximum Trailer Rating or Tongue Weight. The only way to be sure you are not exceeding any of these ratings is to weigh your vehicle and trailer. Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires.
Page 309: Driving With A Trailer
Driving with a Trailer CAUTION: If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You cannot see or smell CO. It can cause unconsciousness or death. See Engine Exhaust on page 2-40.
Page 310: Following Distance
Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing You will need more passing distance up ahead when you are towing a trailer.
Page 311: Driving On Grades
Driving on Grades Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you do not shift down, you might have to use your brakes so much that they would get hot and no longer work well. If you are towing a trailer that weighs more than 1,000 lbs (450 kg), you may prefer to drive in THIRD (3) instead of AUTOMATIC OVERDRIVE (D) or, as you...
Page 312: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you do the following: • Start your engine. • Shift into a gear. • Release the parking brake. 2.
Page 313: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-3 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of Your Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-5 California Fuel ...5-6 Additives ...5-6 Fuels in Foreign Countries ...5-7 Filling the Tank ...5-8 Filling a Portable Fuel Container ...5-10...
Page 314 Section 5 Wheel Alignment and Tire Balance ...5-62 Wheel Replacement ...5-62 Tire Chains ...5-64 Accessory Inﬂator ...5-64 If a Tire Goes Flat ...5-66 Changing a Flat Tire ...5-66 Removing the Spare Tire and Tools ...5-68 Removing the Flat Tire and Installing the Spare Tire ...5-71 Secondary Latch System ...5-77 Storing a Flat or Spare Tire and Tools ...5-79...
Page 315: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 316: Doing Your Own Service Work
Doing Your Own Service Work CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before you attempt any vehicle maintenance task.
Page 317: Adding Equipment To The Outside Of Your Vehicle
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle.
Page 318: California Fuel
California Fuel If your vehicle is certiﬁed to meet California Emissions Standards, it is designed to operate on fuels that meet California speciﬁcations. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal speciﬁcations, but emission control system performance may be affected.
Page 319: Fuels In Foreign Countries
Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber parts. That damage would not be covered under your warranty.
Page 320: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 321 CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Page 322: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 323: Hood Release
Hood Release To open the hood, do the following: 1. Pull the hood release handle with this symbol on it. It is located under the instrument panel on the driver’s side. 2. Go to the front of the vehicle and push the underhood release to the right.
Page 324: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.5L V6 engine, here is what you will see: 5-12...
Page 325 A. Underhood Fuse Block. See Underhood Fuse Block on page 5-96. B. Remote Positive (+) Terminal. See Jump Starting on page 5-38. C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-34. D. Radiator Pressure Cap. See Radiator Pressure Cap on page 5-26.
Page 326 When you open the hood on the 3.9L V6 engine, here is what you will see: 5-14...
Page 327: Engine Oil
A. Underhood Fuse Block. See Underhood Fuse Block on page 5-96. B. Remote Positive (+) Terminal. See Jump Starting on page 5-38. C. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-34. D. Radiator Pressure Cap. See Radiator Pressure Cap on page 5-26.
Page 328: When To Add Engine Oil
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, you will need to add at least one quart/liter of oil. But you must use the right kind. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-99.
Page 329: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for two things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. You should look for and use only an oil that meets GM Standard GM6094M. • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle.
Page 330: Engine Oil Life System
If you are in an area of extreme cold, where the temperature falls below 20°F ( 29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil. Both will provide easier cold starting and better protection for your engine at extremely low temperatures.
Page 331: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and ﬁlter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL SOON message being turned on, reset the system.
Page 332: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-12 for the location of the engine air cleaner/ﬁlter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after each 50,000 mile (83 000 km) interval.
Page 333: Automatic Transaxle Fluid
CAUTION: Operating the engine with the air cleaner/ﬁlter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop ﬂames if the engine backﬁres. If it is not there and the engine backﬁres, you could be burned.
Page 334 Wait at least 30 minutes before checking the transaxle ﬂuid level if you have been driving: • When outside temperatures are above 90°F (32°C). • At high speed for quite a while. • In heavy traffic — especially in hot weather. •...
Page 335: Engine Coolant
How to Add Automatic Transaxle Fluid Refer to the Maintenance Schedule to determine what kind of transaxle ﬂuid to use. See Recommended Fluids and Lubricants on page 6-12. If the ﬂuid level is low, add only enough of the proper ﬂuid to bring the level into the cross-hatched area on the dipstick.
Page 336: What Engine Coolant To Use
What Engine Coolant to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 337: Checking Coolant
Checking Coolant The coolant recovery tank is located on the driver’s side of the vehicle, above the engine air cleaner/ﬁlter. See Engine Compartment Overview on page 5-12 for more information on location. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at the full cold mark, or a little higher.
Page 338: Radiator Pressure Cap
Radiator Pressure Cap Notice: The radiator cap on your vehicle is a pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating. Be sure the arrows on the cap line up with the overﬂow tube on the radiator ﬁller neck. See Engine Compartment Overview on page 5-12 for more information on location.
Page 339: Overheated Engine Protection Operating Mode
If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: • Climb a long hill on a hot day.
Page 340: Cooling System
Cooling System When you decide it is safe to lift the hood, here is what you will see: 3.5L V6 Engine A. Radiator Pressure Cap B. Electric Engine Cooling Fans C. Coolant Recovery Tank 5-28 3.9L V6 Engine A. Radiator Pressure Cap B.
Page 341 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down.
Page 342 How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet, but the coolant level is not at or above the full cold mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL engine coolant at the coolant recovery tank.
Page 343: How To Add Coolant To The Radiator
If the overheat warning continues, there is one more thing you can try. You can add the proper coolant mixture directly at the pressure cap port, but be sure the cooling system is cool before you do it. CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
Page 344 2. Then keep turning the pressure cap, but now push down as you turn it. Remove the pressure cap. CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough.
Page 345 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. 7. By this time, the coolant level inside the radiator ﬁller neck may be lower. If the level is lower, add more of the proper DEX-COOL through the ﬁller neck until the level reaches the base of the ﬁller neck.
Page 346: Power Steering Fluid
Power Steering Fluid The power steering ﬂuid reservoir is located toward the rear of the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise.
Page 347: Brakes
Adding Washer Fluid Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. See Engine Compartment Overview on page 5-12 for reservoir location. Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water.
Page 348: What To Add
So, it is not a good idea to top off your brake ﬂuid. Adding brake ﬂuid will not correct a leak. If you add ﬂuid when your linings are worn, then you will have too much ﬂuid when you get new brake linings. You should add or remove brake ﬂuid, as necessary, only when work is done on the brake hydraulic system.
Page 349: Brake Wear
Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.
Page 350: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts.
Page 351 CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
Page 352 4. Open the hoods and locate the batteries. Find the positive (+) and negative ( ) terminal locations on each vehicle. You will not need to access your battery for jump starting. Your vehicle has a remote positive (+) jump starting terminal for that purpose.
Page 353 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 354 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( ) cable to the negative ( ) terminal of the good battery.
Page 355: All-Wheel Drive
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( ) cable from the vehicle with the good battery. 3.
Page 356 What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 6-12. Carrier Assembly-Differential (Rear Drive Module) When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it.
Page 357: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-48. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 358 To replace one of these bulbs, do the following: 1. Open the hood. See Hood Release on page 5-11 for more information. 2. Remove the headlamp retainer pin (A) by turning it towards the headlamp assembly and pulling it straight out. 5-46 3.
Page 359: Front Turn Signal, Parking And Daytime Running Lamps (Drl)
Front Turn Signal, Parking and Daytime Running Lamps (DRL) To replace one of these bulbs (A), do the following: 1. Follow the Steps 1 through 4 to remove the headlamp assembly. See Headlamps and Sidemarker Lamps on page 5-45 for more information.
Page 360: Replacement Bulbs
A. Stoplamp/Taillamp B. Turn Signal Lamp C. Back-up Lamp Bulb 5. Turn the bulb socket counterclockwise to remove. 6. Replace the bulb by pulling the old bulb out of the socket and gently pushing in a new bulb. 5-48 7. Replace the bulb socket by inserting and turning clockwise to secure.
Page 361: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Normal Maintenance Replacement Parts on page 6-14.
Page 362: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner Manual.
Page 363: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 364 Compact Spare Tire Example (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 365: Tire Terminology And Deﬁnitions
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
Page 366 Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Inﬂation Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat...
Page 367 Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire.
Page 368: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 369: Tire Inspection And Rotation
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 370: When It Is Time For New Tires
Do not include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque”...
Page 371: Buying New Tires
Buying New Tires GM has developed and matched speciﬁc tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Speciﬁcation (TPC spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
Page 372: Different Size Tires And Wheels
CAUTION: If you use bias-ply tires on your vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle. If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and...
Page 373: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Page 374: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 375: Used Replacement Wheels
If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. CAUTION: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be...
Page 376: Tire Chains
Tire Chains CAUTION: Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash.
Page 377 There may be an accessory inﬂator kit stored in the rear compartment on the passenger’s side. It includes a 20-foot (6 m) hose with an air pressure gage and nozzle adapters. CAUTION: Inﬂating something too much can make it explode, and you or others could be injured. Be sure to read the inﬂator instructions, and inﬂate any object only to its recommended pressure.
Page 378: If A Tire Goes Flat
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Page 379 CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1.
Page 380: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The tools you will need are located in the storage compartment at the rear of the vehicle, on the passenger’s side. To remove the tools, do the following: 1. Open the liftgate. See Liftgate on page 2-22 for more information.
Page 381 The tools you will be using include the jack (A), extension (B), and folding wrench (C). The compact spare tire is located under the rear of the vehicle. See Compact Spare Tire on page 5-83 for more information about the compact spare. To remove the compact spare tire, do the following: A.
Page 382 3. Tilt the retainer at the end of the cable to remove the compact spare tire, so it can be pulled up through the wheel opening. If your vehicle is an AWD vehicle, after removing the compact spare tire, turn the wrench clockwise to raise the cable back up.
Page 383: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire If the wheel has a center cap, use the handle of the folding wrench to pry it off. Then, with the other end of the folding wrench, loosen the nuts. If your vehicle has the plastic bolt-on wheel covers, loosen the bolts completely using the folding wrench, and remove the wheel cover.
Page 384 Notice: If you use a jack to raise the vehicle without positioning it correctly, you could damage your vehicle. When raising your vehicle on a jack, avoid contact with the rear axle control arms. Notice: If you position the jack under the rocker molding and attempt to raise the vehicle, you could break the molding and/or cause other damage to your vehicle.
Page 385 3. Put the compact spare tire near you. CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even...
Page 386 5. Raise the vehicle by turning the folding wrench clockwise in the jack. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to ﬁt under the wheel well. 6. Remove all the wheel nuts and take off the ﬂat tire. 5-74 CAUTION: Rust or dirt on the wheel, or on the parts to...
Page 387 7. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 8.
Page 388 9. Lower the vehicle by attaching the folding wheel wrench to the jack and turning the wrench counterclockwise. Lower the jack completely. 5-76 CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident.
Page 389: Secondary Latch System
10. Tighten the wheel nuts ﬁrmly in a crisscross sequence, as shown. Notice: Wheel covers will not ﬁt on your compact spare. If you try to put a wheel cover on the compact spare, you could damage the cover or the spare. 11.
Page 390 To release the spare tire from the secondary latch, do the following: 1. Place the jack under the vehicle, ahead of the rear bumper. Position the center lift point of the jack under the center of the compact spare tire. 2.
Page 391: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. Storing the Spare Tire CAUTION: The underbody-mounted spare tire needs to be...
Page 392 3. Slide the cable retainer through the center of the wheel and start to raise the tire. Make sure the retainer is fully seated across the underside of the wheel. 4. When the tire is almost in the stored position, turn the tire so the valve is towards the rear of the vehicle.
Page 393 Storing the Flat Tire on an All-Wheel-Drive Vehicle 1. Remove the tire storage bag and cable package from the jack storage area. 2. Remove the small center cap by tapping the back of the cap with the extension of the shaft, if the vehicle has aluminum wheels.
Page 394 5. Hook the cable onto the outside portion of the liftgate hinges. 6. Pull on the cable to make sure it is secure. 7. Make sure the metal tube is centered at the striker. Push the tube towards the front of the vehicle.
Page 395: Compact Spare Tire
To put the cover back on, line up the tabs on the right of the cover with the slots in the cover opening. Push the cover in place and push down the tab so that it rests in the groove. This secures the cover in place. Store the center cap or the plastic bolt-on wheel covers until a full size tire is put back on the vehicle.
Page 396: Appearance Care
Appearance Care Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery.
Page 397: Fabric/Carpet
• Use only mild, neutral-pH soaps. Avoid laundry detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.
Page 398: Leather
Leather A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry.
Page 399: Care Of Safety Belts And Built-In Child Restraint Harness
Care of Safety Belts and Built-in Child Restraint Harness Keep the safety belts and the built-in child restraint harness clean and dry. CAUTION: Do not bleach or dye safety belts or the built-in child restraint harness. If you do, they may be severely weakened.
Page 400: Finish Care
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint ﬁnish. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 5-91. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint ﬁnish may damage it.
Page 401: Aluminum Wheels
Aluminum Wheels Notice: If you use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only GM-approved cleaners on aluminum or chrome-plated wheels.
Page 402: Sheet Metal Damage
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.
Page 403: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Removes tar, road oil, Oil Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel. White Sidewall Removes soil and black Tire Cleaner marks from whitewalls.
Page 404: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 405: Electrical System
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 406: Fuses And Circuit Breakers
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers, and fusible thermal links. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating.
Page 407 Fuses Usage Trunk, Door Locks Electronic Level Control Rear Wiper Radio Ampliﬁer Interior Lamps ® OnStar Keyless Entry Module Cluster, Heating, Ventilation, Air Conditioning Cruise Switch Steering Wheel Illumination Power Mirror Stoplamp, Turn Lamps Heated Seats Blank Electronic Level Control Heated Mirror Center High-Mounted Stoplamp, Back-up Lamps...
Page 408: Underhood Fuse Block
Underhood Fuse Block The underhood fuse block is located in the engine compartment. For more information on location see Engine Compartment Overview on page 5-12. Your vehicle may not have all the fuses listed. 5-96...
Page 409 Fuses Usage Right High Beam Fuel Pump Diode SPARE Spare SPARE Spare Left High Beam SPARE Spare SPARE Spare SPARE Spare Not Used Air Conditioning Clutch Horn Left Low Beam Powertrain Control Module, Electronic Throttle Control Not Used Transmission Solenoid Right Low Beam Fuses Usage...
Page 410 J-Case Fuses Fuse Puller Fan 1 Starter Solenoid Anti-lock Brake System Motor Blank Fan 2 Front Blower High Battery Main 3 Rear Defogger Battery Main 2 Spare 5-98 Usage Relays RUN RLY LO BEAM FUEL PUMP AC/CLTCH HI BEAM PWR/TRN IGN MAIN BLANK Usage...
Page 411: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric measurements. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Automatic Transaxle — Pan Removal and Replacement AWD Automatic Transaxle — Pan Removal and Replacement Cooling System Front A/C Front and Rear A/C...
Page 412 NOTES 5-100...
Page 413 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-3 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-12...
Page 414: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 415: Using The Maintenance Schedule
Using the Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather.
Page 416: Scheduled Maintenance
If you want to purchase service information, see Service Publications Ordering Information on page 7-15. Owner Checks and Services on page 6-8 tells you what should be checked, when to check it, and what you can easily do to help keep your vehicle in good condition.
Page 417 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-15. Reset oil life system. See Engine Oil Life System on page 5-18. An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage.
Page 418: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 419: Maintenance Footnotes
Maintenance Footnotes # Lubricate the suspension, steering linkage, transaxle shift linkage, and the underbody contact points and linkage. (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc. Inspect disc brake pads for wear and rotors for surface condition.
Page 420: Owner Checks And Services
(h) Change automatic transaxle ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 421: At Least Once A Month
Engine Coolant Level Check Check the engine coolant level and add ® DEX-COOL coolant mixture if necessary. See Engine Coolant on page 5-23 for further details. Windshield Washer Fluid Level Check Check the windshield washer ﬂuid level in the windshield washer ﬂuid reservoir and add the proper ﬂuid if necessary.
Page 422: Ignition Transaxle Lock Check
Automatic Transaxle Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
Page 423: Underbody Flushing Service
Parking Brake and Automatic Transaxle Park (P) Mechanism Check CAUTION: When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Page 424: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines starburst symbol.
Page 425 Usage Fluid/Lubricant Hood Latch Assembly, Lubriplate Lubricant Aerosol (GM Secondary Part No. U.S. 12346293, in Canada Latch, Pivots, 992723) or lubricant meeting Spring Anchor, requirements of NLGI #2, Category and Release LB or GC-LB. Pawl Hood and Door Hinges, Rear Folding Seat, Multi-Purpose Lubricant, Superlube Fuel Door...
Page 426: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer. Part Engine Air Cleaner/Filter 3.5L V6 Engine 3.9L V6 Engine Engine Oil Filter 3.5L V6 Engine 3.9L V6 Engine Passenger Compartment Air Filter Spark Plugs 3.5L V6 Engine 3.9L V6 Engine...
Page 427: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Page 428 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 429: Customer Assistance And Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-4 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Reimbursement Program ...7-6 Roadside Assistance Program ...7-6 Courtesy Transportation ...7-8 Vehicle Data Collection and Event Data Recorders ...7-10 Collision Damage Repair ...7-11 Customer Assistance and Information...
Page 430: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 431 STEP THREE: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you should ﬁle with the BBB Auto Line Program to enforce any additional rights you may have.
Page 432: Online Owner Center
Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Chevrolet, refer to the addresses below. United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 433 From Puerto Rico: 1-800-496-9992 (English) 1-800-496-9993 (Spanish) Fax Number: 313-381-0022 From U.S. Virgin Islands: 1-800-496-9994 Fax Number: 313-381-0022 Canada — Customer Assistance General Motors of Canada Limited Customer Communication Centre, 163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800...
Page 434: Gm Mobility Reimbursement Program
1-800-GM-DRIVE (463-7483) for details. TTY users call 1-800-263-3830. Roadside Assistance Program As the owner of a new Chevrolet vehicle, you are automatically enrolled in the Chevrolet Roadside Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road.
Page 435: Canadian Roadside Assistance
Roadside Assistance is not part of or included in the coverage provided by the New Vehicle Limited Warranty. Chevrolet reserves the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 436: Courtesy Transportation
Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for new vehicles. The Courtesy Transportation program is offered to customers in conjunction with the Bumper-to-Bumper coverage provided by the New Vehicle Limited Warranty. Several transportation options are available when warranty repairs are required.
Page 437: Additional Program Information
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for a warranty repair. Reimbursement will be limited to a maximum amount per day and must be supported by receipts.
Page 438: Vehicle Data Collection And Event Data Recorders
Vehicle Data Collection and Event Data Recorders Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the vehicle in difficult driving situations.
Page 439: Collision Damage Repair
Others, such as law enforcement, may have access to the special equipment that can read the information if they have access to the vehicle or the device that stores the data. If your vehicle is equipped with OnStar ® the OnStar subscription service agreement or manual for information on its operations and data collection.
Page 440 Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are signiﬁcant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts.
Page 441 • Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identiﬁcation Number (VIN), insurance company and policy number, and a general description of the damage to the other vehicle.
Page 442: Reporting Safety Defects
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying General Motors.
Page 443: Reporting Safety Defects To General Motors
General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you will notify General Motors. Please call the Chevrolet Customer Assistance Center at 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 444: Current And Past Model Order Forms
Owner’s Information Owner publications are written speciﬁcally for owners and intended to provide basic operational information about the vehicle. The owner’s manual will include the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner’s Manual, and Warranty Booklet. RETAIL SELL PRICE: $35.00 Without Portfolio: Owner’s Manual only.
Page 445 Accessories and Modiﬁcations ... 5-3 Accessory Inﬂator ... 5-64 Accessory Power Outlet(s) ... 3-22 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-88 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-93 Air Cleaner/Filter, Engine ... 5-20 Air Conditioning ... 3-24 Airbag Passenger Status Indicator ...
Page 446 Audio System(s) (cont.) Setting the Time ... 3-78 Theft-Deterrent Feature ... 3-113 Understanding Radio Reception ... 3-115 XM™ Satellite Radio Antenna System ... 3-116 Automatic Door Lock ... 2-12 Automatic Transaxle Fluid ... 5-21 Operation ... 2-34 Battery ... 5-38 Run-Down Protection ...
Page 447 Child Restraints (cont.) Child Restraint Systems ... 1-46 Infants and Young Children ... 1-43 Lower Anchors and Tethers for Children ... 1-52 Older Children ... 1-40 Securing a Child Restraint in a Rear Seat Position ... 1-58 Securing a Child Restraint in the Right Front Seat Position ...
Page 448 Daytime Running Lamps/Automatic Headlamp System ... 3-15 Defensive Driving ... 4-2 Delayed Lighting ... 3-18 Delayed Locking ... 2-12 Doing Your Own Service Work ... 5-4 Dome Lamp ... 3-17 Door Automatic Door Lock ... 2-12 Delayed Locking ... 2-12 Dual Sliding Doors ...
Page 449 Engine Air Cleaner/Filter ... 5-20 Battery ... 5-38 Check and Service Engine Soon Light ... 3-41 Coolant ... 5-23 Coolant Heater ... 2-33 Coolant Temperature Gage ... 3-40 Engine Compartment Overview ... 5-12 Exhaust ... 2-40 Oil ... 5-15 Oil Life System ... 5-18 Overheated Protection Operating Mode ...
Page 450 Gage Engine Coolant Temperature ... 3-40 Fuel ... 3-45 Speedometer ... 3-33 Tachometer ... 3-33 Garage Door Opener ... 2-44 Gasoline Octane ... 5-5 Speciﬁcations ... 5-5 Glove Box ... 2-48 GM Mobility Reimbursement Program ... 7-6 Hazard Warning Flashers ... 3-6 Head Restraints ...
Page 451 Ignition Positions ... 2-31 Infants and Young Children, Restraints ... 1-43 Inﬂation -- Tire Pressure ... 5-56 Instrument Panel Overview ... 3-4 Instrument Panel (I/P) Brightness ... 3-16 Cluster ... 3-32 Interior Lamps Control ... 3-17 Jump Starting ... 5-38 Keyless Entry System ...
Page 452 Light (cont.) Passenger Safety Belt Reminder ... 3-34 Safety Belt Reminder ... 3-33 Security ... 3-45 TCS Warning Light ... 3-40 Traction Control System (TCS) Warning ... 3-40 Lighting Delayed ... 3-18 Entry ... 3-17 Exit ... 3-18 Loading Your Vehicle ... 4-30 Lockout Protection ...
Page 453 New Vehicle Break-In ... 2-30 Normal Maintenance Replacement Parts ... 6-14 Odometer ... 3-33 Odometer, Trip ... 3-33 Off-Road Recovery ... 4-14 Engine ... 5-15 Pressure Light ... 3-44 Oil, Engine Oil Life System ... 5-18 Older Children, Restraints ... 1-40 Online Owner Center ...
Page 454 Questions and Answers About Safety Belts ... 1-25 Radiator Pressure Cap ... 5-26 Radios ... 3-77 Care of Your CD and DVD Player ... 3-116 Care of Your CDs and DVDs ... 3-115 Radio with CD ... 3-79 Rear Seat Audio ... 3-111 Setting the Time ...
Page 455 Safety Belt Passenger Reminder Light ... 3-34 Pretensioners ... 1-39 Reminder Light ... 3-33 Safety Belts Care of Safety Belts and Built-in Child Restraint Harness ... 5-87 Driver Position ... 1-26 How to Wear Safety Belts Properly ... 1-26 Questions and Answers About Safety Belts ... 1-25 Rear Safety Belt Comfort Guides ...
Page 456 Spare Tire Accessory Inﬂator ... 5-64 Compact ... 5-83 Installing ... 5-71 Removing ... 5-68 Storing ... 5-79 Speciﬁcations, Capacities ... 5-99 Speedometer ... 3-33 ® StabiliTrak System ... 4-9 Starting Your Engine ... 2-32 Steering ... 4-11 Steering Wheel Controls, Audio ... 3-114 Steering Wheel, Tilt Wheel ...
Page 457 Tires (cont.) Tire Sidewall Labeling ... 5-51 Tire Terminology and Deﬁnitions ... 5-53 Uniform Tire Quality Grading ... 5-61 Wheel Alignment and Tire Balance ... 5-62 Wheel Replacement ... 5-62 When It Is Time for New Tires ... 5-58 Towing Recreational Vehicle ...
Page 458 Warning Lights, Gages and Indicators ... 3-31 Warnings DIC Warnings and Messages ... 3-53 Hazard Warning Flashers ... 3-6 Other Warning Devices ... 3-6 Safety and Symbols ... iii Vehicle Damage ... iv Wheels Alignment and Tire Balance ... 5-62 Different Size ...

This manual is also suitable for:

Uplander Uplander 2006

Chevrolet 2005 Uplander Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Universal Home Remote System

Storage Areas

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

All-Wheel Drive

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Chevrolet 2005 Uplander

Summary of Contents for Chevrolet 2005 Uplander