Chevrolet 2005 Express Van Owner's Manual

page of 370

/ 370
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

2005 Chevrolet Express Owner Manual

Seats and Restraint Systems ........................... 1-1

Front Seats

............................................... 1-3

Rear Seats

............................................... 1-6

Safety Belts

............................................. 1-10

Child Restraints

....................................... 1-31

Airbag System

......................................... 1-59

Restraint System Check

Features and Controls ..................................... 2-1

Keys

........................................................ 2-2

Doors and Locks

....................................... 2-7

Windows

................................................. 2-15

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

.................................................... 2-29

OnStar

System

...................................... 2-31

Storage Areas

......................................... 2-32

Instrument Panel ............................................. 3-1

Instrument Panel Overview

Climate Controls

...................................... 3-18

Warning Lights, Gages, and Indicators

Audio System(s)

....................................... 3-39

Driving Your Vehicle ....................................... 4-1

Your Driving, the Road, and Your Vehicle

Towing

................................................... 4-34

............................ 1-70

............................ 2-18

........... 2-18

.......................... 3-4

........ 3-22

........ 4-2

Service and Appearance Care .......................... 5-1

Service

..................................................... 5-3

Fuel

......................................................... 5-5

Checking Things Under the Hood

All-Wheel Drive

........................................ 5-43

Rear Axle

............................................... 5-44

Front Axle

............................................... 5-44

Noise Control System

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

...................................................... 5-52

Appearance Care

..................................... 5-82

Vehicle Identiﬁcation

Electrical System

...................................... 5-92

Capacities and Speciﬁcations

Maintenance Schedule ..................................... 6-1

Maintenance Schedule

Customer Assistance and Information .............. 7-1

Customer Assistance and Information

Reporting Safety Defects

Index .................................................................1

............... 5-10

............................... 5-45

.................................... 5-46

......... 5-51

................................. 5-91

..................... 5-97

................................ 6-2

........... 7-2

........................... 7-10

Table of Contents

Chapters

Table of Contents

Summary of Contents for Chevrolet 2005 Express Van

Page 1 2005 Chevrolet Express Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-3 Rear Seats ... 1-6 Safety Belts ... 1-10 Child Restraints ... 1-31 Airbag System ... 1-59 Restraint System Check ... 1-70 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division whenever it appears in this manual. Keep this manual in the vehicle, so it will be there if it is needed while you are on the road.
Page 3 Safety Warnings and Symbols There are a number of safety cautions in this book. We use a box and the word CAUTION to tell about things that could hurt you if you were to ignore the warning. CAUTION: These mean there is something that could hurt you or other people.
Page 4 Vehicle Damage Warnings Also, in this manual you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 5 These are some examples of symbols that may be found on the vehicle:...
Page 6 NOTES...
Page 7: Table Of Contents
Section 1 Front Seats ...1-3 Manual Seats ...1-3 Power Seat ...1-4 Reclining Seatbacks ...1-4 Rear Seats ...1-6 Rear Seat Operation ...1-6 Safety Belts ...1-10 Safety Belts: They Are for Everyone ...1-10 Questions and Answers About Safety Belts ...1-14 How to Wear Safety Belts Properly ...1-15 Driver Position ...1-15 Shoulder Belt Height Adjustment ...1-22 Safety Belt Use During Pregnancy ...1-23...
Page 8 Section 1 What Makes an Airbag Inﬂate? ...1-64 How Does an Airbag Restrain? ...1-65 What Will You See After an Airbag Inﬂates? ...1-65 Airbag Off Switch ...1-66 Servicing Your Airbag-Equipped Vehicle ...1-69 Adding Equipment to Your Airbag-Equipped Vehicle ...1-70 Seats and Restraint Systems Restraint System Check ...1-70 Checking Your Restraint Systems ...1-70 Replacing Restraint System Parts...
Page 9: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 10: Power Seat
Power Seat If your vehicle has front power seat(s), you can adjust them with these controls located at the front center of the seat cushion. To raise or lower the seat, move the center knob up or down. To move the seat forward or rearward, move the center knob toward the right or left.
Page 11 But don’t have a seatback reclined if your vehicle is moving. CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can not do their job when you are reclined like this. The shoulder belt can not do its job because it will not be against your body.
Page 12: Rear Seats
Rear Seats Rear Seat Operation Removing the Rear Seat 1. Disconnect the quick release latch plates for the lap shoulder belts on the bench seat to be removed. To do this, press the tip of a key into the release hole of the safety belt buckle while pulling up on the safety belt.
Page 13 • The passenger’s side pin has a black cap with a white “R” marked on it: 3. Pull the pin handle up to disengage the pin from the retaining clip, then pull the pin out. 4. Repeat this procedure for the pin on the other seat base.
Page 14 Replacing the Rear Seats CAUTION: A seat that is not locked into place properly can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to lock the seat into place properly when installing it.
Page 15 4. Push the pin with the black cap marked “R” down until it is in the retaining clip. 5. Push the pin with the gray cap marked “L” down until it is in the retaining clip. 6. If the vehicle has a ﬂoor mat, put the ﬂap back to its original position.
Page 16: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Do not let anyone ride where he or she can not wear a safety belt properly.
Page 17: Why Safety Belts Work
Your vehicle has a light that comes on as a reminder to buckle up. See Safety Belt Reminder Light on page 3-25. In most states and in all Canadian provinces, the law says to wear safety belts. Here is why: They work. You never know if you will be in a crash.
Page 18 Put someone on it. 1-12 Get it up to speed. Then stop the vehicle. The rider does not stop.
Page 19 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-13...
Page 20: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. 1-14 Questions and Answers About Safety Belts...
Page 21: Driver Position
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in an accident — even one that is not your fault — you and your passengers can be hurt.
Page 22 4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 1-30. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 23 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 24 What is wrong with this? The belt is buckled in the wrong place. 1-18 CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 25 What is wrong with this? The belt is over an armrest. CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt.
Page 26 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-20 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 27 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 28: Shoulder Belt Height Adjustment
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 29: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 30: And 5Th Row)
Center Passenger Position (3rd, 4th and 5th Row) Lap Belt If your vehicle has third, fourth or ﬁfth row bench seats, someone can sit in the center positions. When you sit in a center seating position in the third, fourth or ﬁfth row, you have a lap safety belt, which has no retractor.
Page 31: Rear Seat Passengers
Rear Seat Passengers It’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash.
Page 32 3. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder part. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Page 33 The safety belt locks if there is a sudden stop or a crash. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. To unlatch the belt, just push the button on the buckle.
Page 34: Rear Safety Belt Comfort Guides For Children And Small Adults
Rear Safety Belt Comfort Guides for Children and Small Adults Rear safety belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When installed on a shoulder belt, the comfort guide better positions the belt away from the neck and head.
Page 35 2. Place the guide over the belt and insert the 3. Be sure the belt is not twisted and it lies ﬂat. The two edges of the belt into the slots of the guide. elastic cord must be under the belt and the guide on top.
Page 36: Safety Belt Pretensioners
4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-25. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
Page 37: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. If you have the choice, a child should sit in a seating position that has a lap-shoulder belt to get the additional restraint a shoulder belt can provide. What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a...
Page 38 CAUTION: Never do this. Here two children are wearing the same belt. The belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. 1-32 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt...
Page 39: Infants And Young Children
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 40 Cargo Vans with a Passenger Airbag and an Airbag Off Switch, Passenger Vans, and Cab and Chassis Models 1-34 CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby does not weigh much — until a crash. During a crash a baby will become so heavy it is not possible to hold it.
Page 41 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 42 For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards.
Page 43 Cargo Vans with a Passenger Airbag and without an Airbag Off Switch CAUTION: Children who are up against, or very close to, an airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer outstanding protection for adults and older children, but not for young children and infants.
Page 44 CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 45: Child Restraint Systems
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous ﬂat surface. Make sure that the infant’s head rests toward the center of the vehicle.
Page 46 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. 1-40 A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness.
Page 47 How do child restraints work? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Page 48: Where To Put The Restraint
Where to Put the Restraint Passenger Vans without an Airbag Off Switch Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We, therefore, recommend that child restraints be secured in a rear seat including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 49 Passenger Vans with an Airbag Off Switch Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We, therefore, recommend that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 50 Cargo Vans and Cab and Chassis Models without an Airbag Off Switch The child restraint must be secured properly in the right front passenger seat. If your vehicle has a passenger airbag, never use a rear-facing child restraint in this vehicle Here is why: CAUTION: A child in a rear-facing child restraint can be...
Page 51 Cargo Vans and Cab and Chassis Models with an Airbag Off Switch The child restraint must be secured properly in the right front passenger seat. If you need to secure a rear-facing child restraint in the right front passenger’s seat, turn off the passenger’s airbag. See Airbag Off Switch on page 1-66 and Securing a Child Restraint in the Right Front Seat Position on page 1-55 for more on this, including important safety information.
Page 52: Top Strap
Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 53: Top Strap Anchor Location
Anchor the top strap to one of the following anchor points. Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed. CAUTION: Each top tether bracket is designed to anchor only one child restraint.
Page 54 Second Row For the second row only, in the left outboard seating position, use anchor point (A). For the right outboard seating position, use anchor point (B). For a center seating position, use either anchor point (A) or (B). 1-48 Cargo Van Cargo Van On cargo vans with a front passenger seat, the anchor...
Page 55: Lower Anchorages And Top Tethers For Children (Latch System)
Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle may have the LATCH system. If it does, you will ﬁnd two sets of anchors in the second row of seats in the outside seating positions, where the seatback meets the seat cushion. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts.
Page 56 A. Lower Anchorage B. Lower Anchorage In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. 1-50 To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback at each...
Page 57: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System 1. Find the LATCH anchorages for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. See Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-49.
Page 58 3. Buckle the belt. Make sure the release button is 4. Pull the rest of the shoulder belt all the way out of positioned so you would be able to unbuckle the the retractor to set the lock. safety belt quickly if you ever had to. 1-52...
Page 59: Securing A Child Restraint In A Center Seat Position (2Nd Row)
5. To tighten the belt, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 60: Securing A Child Restraint In A Center Seat Position (3Rd, 4Th And 5Th Row)
Securing a Child Restraint in a Center Seat Position (3rd, 4th and 5th Row) If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-49. See Top Strap on page 1-46 if the child restraint has one.
Page 61: Securing A Child Restraint In The Right Front Seat Position
4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. To tighten the belt, pull its free end while you push down on the child restraint. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 62 Unless your vehicle has an airbag off switch and you have used it to turn the passenger’s airbag off, never put a rear-facing child restraint in the right front passenger’s seat. Here is why: CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates.
Page 63 CAUTION: If the airbag readiness light ever comes on when you have turned off the airbag, it means that something may be wrong with the airbag system. The right front passenger’s airbag could inﬂate even though the switch is off. If this ever happens, do not let anyone whom the national government has identiﬁed as a member of a passenger airbag risk group sit in...
Page 64 5. Pull the rest of the lap belt all the way out of the retractor to set the lock. 1-58 6. To tighten the belt, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 65: Airbag System
If you were using a rear-facing child restraint in a vehicle with an airbag off switch, turn on the right front passenger’s airbag when you remove the rear-facing child restraint from the vehicle unless the person who will be sitting there is a member of a passenger airbag risk group.
Page 66 If it says AIR BAG on the middle part of the steering wheel, but there is no right front passenger seat, your vehicle has an airbag for the driver only. Frontal airbags are designed to help reduce the risk of injury from the force of an inﬂating airbag.
Page 67 If your vehicle has an airbag for the right front passenger read this. CAUTION: Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants.
Page 68: Where Are The Airbags
Where Are the Airbags? The driver’s airbag is in the middle of the steering wheel. 1-62 If your vehicle has one, the right front passenger’s airbag is in the instrument panel on the passenger’s side.
Page 69: When Should An Airbag Inﬂate
CAUTION: If something is between an occupant and an airbag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death. The path of an inﬂating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other...
Page 70: What Makes An Airbag Inﬂate
If the GVWR (Gross Vehicle Weight Rating) of your vehicle is 8,500 lb (3 855 kg) or above, your vehicle has single stage airbags. If the GVWR is below 8,500 lb (3 855 kg) then your vehicle has dual stage airbags. You can ﬁnd the GVWR on the certiﬁcation label on the rear edge of the driver’s door.
Page 71: How Does An Airbag Restrain
How Does an Airbag Restrain? In moderate to severe frontal or near-frontal collisions, even belted occupants can contact the steering wheel or the instrument panel. Airbags supplement the protection provided by safety belts. Airbags distribute the force of the impact more evenly over the occupant’s upper body, stopping the occupant more gradually.
Page 72: Airbag Off Switch
• Your vehicle is equipped with a crash sensing and diagnostic module which records information after a crash. See Vehicle Data Collection and Event Data Recorders on page 7-9. • Let only qualiﬁed technicians work on your airbag system. Improper service can mean that your airbag system will not work properly.
Page 73 This switch should only be turned to airbag OFF if the person in the right front passenger’s position is a member of a passenger risk group identiﬁed by the national government as follows: Infant. An infant (less than 1 year old) must ride in the front seat because: •...
Page 74 United States To turn off the right front passenger’s airbag, insert your ignition key into the switch, push in, and move the switch to the off position. The airbag off light will come on to let you know that the right front passenger’s airbag is off.
Page 75: Servicing Your Airbag-Equipped Vehicle
United States To turn the right front passenger’s airbag on, insert your ignition key into the switch, push in, and move the switch to the on position. Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle.
Page 76: Adding Equipment To Your Airbag-Equipped Vehicle
Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to the front of the vehicle that could keep the airbags from working properly? Yes. If you add things that change your vehicle’s frame, bumper system, front end sheet metal or height, they may keep the airbag system from working properly.
Page 77: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 78 NOTES 1-72...
Page 79: Features And Controls
Section 2 Keys ...2-2 Remote Keyless Entry System ...2-3 Remote Keyless Entry System Operation ...2-4 Doors and Locks ...2-7 Door Locks ...2-7 Power Door Locks ...2-8 Cargo Door Relocking ...2-8 Rear Door Security Locks ...2-8 Lockout Protection ...2-9 Sliding Side Door ...2-10 60/40 Swing-Out Side Door ...2-12 Rear Doors ...2-13 Windows ...2-15...
Page 80: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed.
Page 81: Remote Keyless Entry System
This vehicle has one double-sided key for the ignition and door locks. It will ﬁt with either side up. When a new vehicle is delivered, the dealer provides the owner with a pair of identical keys and a bar-coded tag. The bar-coded tag has a code on it that tells your dealer or a qualiﬁed locksmith how to make extra keys.
Page 82: Remote Keyless Entry System Operation
Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: •...
Page 83 (Panic Alarm): The remote keyless entry transmitter comes equipped with an instant panic alarm. To use the alarm, press the horn symbol while the ignition is turned off. The horn will sound and both the interior and exterior lamps will ﬂash for up to thirty seconds. To stop the instant panic alarm, press the panic button again, wait for thirty seconds, or start the vehicle.
Page 84: Battery Replacement
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s probably time to change the battery.
Page 85: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 86: Power Door Locks
Power Door Locks Press the bottom side of the power door lock switch to lock all the doors at once. Press the top side of the power door lock switch to unlock all the doors at once. When a door is locked, the inside door handle will not work.
Page 87: Lockout Protection
Move the button to the left to engage the security feature. Move the button to the right to return the door locks to normal operation. Passenger Side 60/40 Swing-Out Side Door Move the button to the right to engage the security feature.
Page 88: Sliding Side Door
Sliding Side Door To open the sliding side door from outside, pull the handle toward the rear of the vehicle. Then, slide the door open. 2-10 To close the sliding side door from outside, use the outside door handle to slide the door toward the front of the vehicle.
Page 89 To open the sliding door from inside, turn the handle upward and toward the rear of the vehicle. Then, slide the door toward the rear of the vehicle to open it. To close the sliding door from inside, grasp the inside handle and slide the door toward the front of the vehicle to a closed position.
Page 90: 60/40 Swing-Out Side Door
60/40 Swing-Out Side Door To open the front portion of a 60/40 door from the outside, pull out on the handle and pull it toward you. 2-12 To open the front portion of a 60/40 door from the inside, pull the handle toward you and push open the door.
Page 91: Rear Doors
To open the rear portion of a 60/40 door from the outside, pull the handle on the side of the rear door and pull it toward you. To close the 60/40 side doors, close the rear door ﬁrst. Then close the front door. Check to make sure that both doors are completely closed.
Page 92 To open the rear doors from the outside, pull the handle toward you to open the passenger’s side rear door ﬁrst. 2-14 To open the driver’s side rear door, pull the latch release at the inside edge of the door. To close the rear doors, close the driver side rear door ﬁrst.
Page 93: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 94: Power Windows
Power Windows If you have power windows, the controls are located on each of the side doors. The driver’s door has a switch for the passenger window as well. Your power windows will work when the ignition has been turned to RUN or ACCESSORY, or when Retained Accessory Power (RAP) is active.
Page 95: Swing-Out Windows
Swing-Out Windows Side Swing-Out Window To open the side door swing-out windows, pull up on the latch at the edge of the window. Swing the window out and push down on the latch to lock the window into place. To close the window, pull the latch toward you and push down on the latch to lock it.
Page 96: Theft-Deterrent Systems
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. ® Passlock Your vehicle is equipped with the Passlock theft-deterrent system.
Page 97: Ignition Positions
Ignition Positions Use the key to turn the ignition switch to four different positions. A (Lock): This position locks the ignition and transmission. It is a theft-deterrent feature. You will only be able to remove the key when the ignition is turned to LOCK.
Page 98: Starting Your Engine
Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Do not try to shift to PARK (P) if your vehicle is moving.
Page 99: Engine Coolant Heater
Engine Coolant Heater In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required.
Page 100: Automatic Transmission Operation
Automatic Transmission Operation There are several different positions for your shift lever. PARK (P): This position locks your rear wheels. It is the best position to use when you start your engine because your vehicle cannot move easily. CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set.
Page 101 CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed.
Page 102: All-Wheel Drive
All-Wheel Drive If your vehicle has all-wheel drive, your engine’s driving power is sent to all four wheels for extra traction when needed. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjusts itself as needed for road conditions.
Page 103: Shifting Into Park (P)
Shifting Into Park (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 104: Shifting Out Of Park (P)
Torque Lock If you are parking on a hill and you do not shift your vehicle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P).
Page 105: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell.
Page 106: Running Your Engine While You Are Parked
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 107: Mirrors
Mirrors Manual Rearview Mirror Inside Day/Night Rearview Mirror Pull the tab under the mirror toward you to reduce glare from headlamps behind you after dark. Push the tab away from you to restore the mirror to the original position. If you have a cargo van without the rear door glass, your vehicle may not have a rearview mirror.
Page 108: Outside Power Mirrors
2. Turn the mirror head so that it swings further outboard and adjust the mirror surface as needed. Outside Power Mirrors If the vehicle has power mirrors, the control is located on the driver’s side door. 2-30 Select each mirror by turning the knob clockwise for the passenger’s side mirror or counterclockwise for the driver’s side mirror.
Page 109: Outside Heated Mirrors
Outside Heated Mirrors Your outside mirrors can be defrosted by pressing the button located near the fan control. An indicator light in the button will light while the heated outside mirrors are activated. Your rear window defogger comes on while the heated mirrors are on.
Page 110: Storage Areas
Safe and Sound Plan • Automatic Notiﬁcation of Airbag Deployment • Emergency Services • Roadside Assistance • Stolen Vehicle Tracking • AccidentAssist • Remote Door Unlock/Vehicle Alert • Remote Diagnostics • Online Concierge Directions and Connections Plan • All Safe and Sound Plan Services •...
Page 111: Instrument Panel
Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-8 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-9 Windshield Wipers ...3-9 Windshield Washer ...3-10 Cruise Control ...3-10 Exterior Lamps ...3-13 Headlamps on Reminder ...3-14...
Page 112 Section 3 Cruise Control Light ...3-36 Reduced Engine Power Light ...3-37 Highbeam On Light ...3-37 Daytime Running Lamps (DRL) Indicator Light ...3-37 Tow/Haul Mode Light ...3-38 Check Gages Warning Light ...3-38 Fuel Gage ...3-38 Audio System(s) ...3-39 Setting the Time for Radios without Radio Data Systems (RDS) ...3-40 Setting the Time for Radios with Radio Data Systems (RDS) ...3-40...
Page 113 NOTES...
Page 114: Instrument Panel Overview
Instrument Panel Overview...
Page 115 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-20. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-23. D.
Page 116: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located on top of the steering column.
Page 117 To tilt the wheel, hold the steering wheel and pull the lever. Move the steering wheel to a comfortable level, then release the lever to lock the wheel in place. Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: •...
Page 118: Turn Signal/Multifunction Lever
Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down.
Page 119: Flash-To-Pass
Flash-to-Pass This feature allows you to use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are off. To use it, pull the turn signal lever toward you, but not so far that you hear it click.
Page 120: Windshield Washer
Windshield Washer (Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed. CAUTION: In freezing weather, do not use your washer until the windshield is warmed.
Page 121 (Off): This position turns the system off. (On): This position activates the system. (Resume/Accelerate): Push the lever to this symbol to make the vehicle accelerate or resume to a previously set speed. (Set): Press this button to set the speed. Setting Cruise Control CAUTION: If you leave your cruise control on when you...
Page 122 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you don’t need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can move the cruise control switch from on to resume/accelerate brieﬂy.
Page 123: Exterior Lamps
Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may want to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down.
Page 124: Headlamps On Reminder
(Parking Lamps): Turn the control to this position to turn on the parking lamps, together with the following: • Instrument Panel Lights • Daytime Running Lamps (DRL) (Canada) • Sidemarker Lamps • Taillamps • License Plate Lamps If the DRL are active when the control is turned to this position, the DRL will turn off.
Page 125: Instrument Panel Brightness
When you turn the headlamp switch off, the headlamps will go off, and your DRL lamps will illuminate. To turn off the DRL, turn the exterior lamp control to the defeat position or shift into PARK (P). The DRL will stay off until the control is toggled again or the vehicle is shifted out of PARK (P).
Page 126: Entry Lighting
Entry Lighting Your vehicle is equipped with an illuminated entry feature. When a door is opened, the dome lamps will come on if the dome override button is in the out position. If the dome override button is pressed in, the lamps will not come on.
Page 127: Ashtrays And Cigarette Lighter
To use the outlet, lift the cover. When not using it, always close the cover. Certain power accessory plugs may not be compatible to the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer for additional information on the accessory power plugs.
Page 128: Climate Controls
Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 129: Defogging And Defrosting
Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control is used properly. There are two modes to clear fog or frost from your windshield and side windows.
Page 130: Outlet Adjustment
Outlet Adjustment Use the outlets located near the center and on the sides of the instrument panel to change the direction of airﬂow. Operation Tips • Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle.
Page 131: Rear Air Conditioning And Heating System
Rear Air Conditioning and Heating System Your vehicle may have a rear heating and air-conditioning system. This system regulates the temperature, the fan speed and the air delivery for the rear-seat passengers only. It also works with the main climate-control system in your vehicle. Front Climate-Control Panel Use this control panel when you would like to maintain a separate temperature setting.
Page 132: Warning Lights, Gages, And Indicators
To change the current mode, select one of the following: (Vent): Use this mode to direct air to the upper outlets, with a little air directed to the ﬂoor outlets. (Floor): Use this mode to direct most of the air to the ﬂoor outlets.
Page 133: Instrument Panel Cluster
Instrument Panel Cluster United States version shown, Canada similar The instrument panel cluster is designed to let you know at a glance how the vehicle is running. You will know how fast you are going, how much fuel you are using, and many other things you will need to know to drive safely and economically.
Page 134: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper resistant odometer.
Page 135: Safety Belt Reminder Light
Safety Belt Reminder Light When the key is turned to RUN or START, a chime will be provided for several seconds to remind people to buckle their safety belts. The driver safety belt light will also be provided and stay on for several seconds, then it will ﬂash for several more.
Page 136: Airbag Off Light
If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly.
Page 137 CAUTION: If the right front passenger’s airbag is turned off for a person who is not in a risk group identiﬁed by the national government, that person will not have the extra protection of an airbag. In a crash, the airbag will not be able to inﬂate and help protect the person sitting there.
Page 138: Charging System Light
Charging System Light This light should come on brieﬂy when you turn on the ignition, before starting the engine, as a check to show you it is working. After the engine starts, the light should go out. If it stays on or comes on while you are driving, you may have a problem with your charging system.
Page 139: Brake System Warning Light
You can only drive for a short time with the reading in either warning zone. If you must drive, turn off all unnecessary accessories. Readings in either warning zone indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible.
Page 140: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Light With the anti-lock brake system, this light will come on when you start your engine and may stay on for several seconds. That’s normal. If the light stays on, or comes on when you’re driving, your vehicle needs service.
Page 141: Stabilitrak Indicator Light
StabiliTrak Indicator Light If you have the StabiliTrak system, this light will be on or ﬂashing, according to the description table for the StabiliTrak For more information, see StabiliTrak page 4-8. You will hear three chimes if the light turns on and one chime if the light turns off.
Page 142: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
Page 143: If The Light Is Flashing
If the Light Is Flashing The following may prevent more serious damage to your vehicle: • Reducing vehicle speed • Avoiding hard accelerations • Avoiding steep uphill grades • If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady”...
Page 144: Oil Pressure Gage
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the Check Engine light is on or not working properly.
Page 145: Maintenance Schedule
A reading in the low pressure zone may be caused by a dangerously low oil level or other problem causing low oil pressure. Check your oil as soon as possible. CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre.
Page 146: Security Light
Security Light United States The light will stay on until the engine starts. If the light ® ﬂashes, the Passlock System has entered a tamper mode. If the vehicle fails to start, see Passlock on page 2-18. If the light comes on continuously while driving and stays on, there may be a problem with the Passlock System.
Page 147: Reduced Engine Power Light
Reduced Engine Power Light If the check engine and reduced engine power lights are on, the throttle may be disabled and a noticeable reduction in the vehicle’s performance may occur. If the reduced engine power light is on, but there is no reduction in performance, proceed to your destination.
Page 148: Tow/Haul Mode Light
Tow/Haul Mode Light This message is displayed when the tow/haul mode has been activated. For more information, see “Tow/Haul Mode” in Towing a Trailer on page 4-34. Check Gages Warning Light United States This light will come on brieﬂy when you are starting the engine.
Page 149: Audio System(S)
Listed are four situations you may experience with your fuel gage: • At the gas station, the fuel pump shuts off before the gage reads full. • It takes a little more or less fuel to ﬁll up than the fuel gage indicated.
Page 150: Setting The Time For Radios Without Radio
Setting the Time for Radios without Radio Data Systems (RDS) Press and hold the HR or MIN arrow for two seconds. Then press HR until the correct hour appears on the display. Press and hold MIN until the correct minute appears on the display.
Page 151 Finding a Station AM FM: Press this button to switch between FM1, FM2, or AM. The display will show the selection. TUNE: Turn this knob to select radio stations. SEEK : Press the right or the left arrow to go to the next or to the previous station and stay there.
Page 152 To adjust both tone controls and both speaker controls to the middle position, ﬁrst end out of audio mode by pressing another button, causing the radio to perform that function, or by waiting ﬁve seconds for the display to return to time of day. Then press and hold AUDIO for more than two seconds until you hear a beep.
Page 153: Radio With Cd
Radio with CD Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. RCL (Recall): Press this knob to switch the display between the radio station frequency and the time. When the ignition is off, press this knob to display the time.
Page 154 Setting Preset Stations Up to 18 stations (six FM1, six FM2, and six AM), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2. Press AM FM to select FM1, FM2, or AM. 3.
Page 155 To adjust balance or fade to the middle position, select BAL or FAD. Then press and hold AUDIO for more than two seconds until you hear a beep. L and a zero or F and a zero will appear on the display. To adjust both tone controls and both speaker controls to the middle position, ﬁrst end out of audio mode by pressing another button, causing the radio to perform...
Page 156 Do not add paper labels to CDs, they could get caught in the CD player. If an error appears on the display, see “CD Messages” later in this section. 1 PREV (Previous): Press this pushbutton to go to the beginning of the current track if more than eight seconds have played.
Page 157: Radio With Cassette And Cd
CD Messages If the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smoother, the CD should play.
Page 158 This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
Page 159 AUTO VOL (Automatic Volume): With automatic volume, the audio system will adjust automatically to make up for road and wind noise as you drive by increasing the volume as vehicle speed increases. Set the volume at the desired level. Press this button to select LOW, MEDIUM, or HIGH.
Page 160 4. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever that numbered pushbutton is pressed, the station that was set will return for that pushbutton. 5. Repeat the steps for each pushbutton. To store an equalization setting to a preset station perform the following: 1.
Page 161 To adjust the balance and fade to the middle position, push the AUDIO knob, then push it again and hold it until the radio produces one beep. The balance and fade will be adjusted to the middle position and the display will show the speaker balance.
Page 162 Setting Preset PTYs (RDS Only) These buttons have factory PTY presets. Up to 12 PTYs (six FM1 and six FM2), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Press BAND to select FM1 or FM2. 2.
Page 163 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code No Signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) CH Off Air Channel not in service CH Unavail Channel no...
Page 164 Radio Display Message No Info Song/Program Title not available No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known...
Page 165: Playing A Cassette Tape
Playing a Cassette Tape The tape player is built to work best with tapes that are up to 30 to 45 minutes long on each side. Tapes longer than that are so thin they may not work well in this player. The longer side with the tape visible should face to the right.
Page 166: Cassette Tape Messages
4 FWD (Forward): Press this pushbutton to quickly advance the tape. The radio will play while the tape advances. Press this pushbutton again to return to playing speed. The station frequency and FWD will appear on the display. Select stations during forward operation by using TUNE and SEEK.
Page 167: Cd Adapter Kits
CLEAN: If this message appears on the display, the cassette tape player needs to be cleaned. It will still play tapes, but it should be cleaned as soon as possible to prevent damage to the tapes and player. See Care of Your Cassette Tape Player on page 3-72.
Page 168 1 PREV (Previous): Press this pushbutton to go to the beginning of the current track if more than eight seconds have played. TRACK and the track number will appear on the display. If this pushbutton is held or pressed more than once, the player will continue moving backward through the CD.
Page 169 © ¨ SCAN : Press and hold either the SCAN or the TYPE arrows for more than two seconds until SCAN appears on the display and you hear a beep. The radio will go to the next track, play for 10 seconds, then go on to the next track.
Page 170: Radio With Six-Disc Cd
Radio with Six-Disc CD Playing the Radio PWR (Power): Push this knob to turn the system on and off. VOLUME : Turn this knob to increase or to decrease the volume. 3-60 INFO (Information): Press this knob to switch the display between the radio station frequency and the time.
Page 171 Finding a Station BAND: Press this button to switch between FM1, FM2, or AM. The display will show the selection. TUNE : Turn this knob to select radio stations. © ¨ SEEK : Press either the SEEK or the TYPE arrows to go to the next or to the previous station and stay there.
Page 172 Setting the Tone (Bass/Treble) AUDIO: Push and release the AUDIO knob until BASS, MID, or TREB appears on the display. Turn the knob to increase or to decrease. The display will show the bass, midrange, or treble level. If a station is weak or noisy, decrease the treble.
Page 173 Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: • Seek to stations broadcasting the selected type of programming •...
Page 174 SCAN: Scan the stations within a PTY by performing the following: 1. Press the TYPE button to activate program type select mode. P-TYPE and the last selected PTY will appear on the display. 2. Turn the TYPE knob or press and release the TYPE button to select a PTY.
Page 175 RDS Messages INFO (Information): If the current station has a message, INFO will appear on the display. Press this button to see the message. The message may display the artist, song title, call in phone numbers, etc. If the entire message is not displayed, parts of the message will appear every three seconds.
Page 176 Playing a CD If the ignition or radio is turned off, with a CD in the player, it will stay in the player. When the ignition or radio is turned on, the CD will start playing where it stopped, if it was the last selected audio source. When a CD is inserted, the CD symbol will appear on the display.
Page 177 To insert multiple CDs, do the following: 1. Turn the ignition on. 2. Press and hold the LOAD button for two seconds. You will hear a beep and the indicator light, located to the right of the slot, will begin to ﬂash and MULTI LOAD # will appear on the display.
Page 178 If the CD is not removed, after 25 seconds, the CD will be automatically pulled back into the player. If CD is pushed back into the player, before the 25 second time period is complete, the player will sense an error and will try to eject the CD several times before stopping.
Page 179: Using Song List Mode
© ¨ SEEK : Press the left arrow to go to the start of the current track, if more than ten seconds have played. Press the right arrow to go to the next track. If either arrow is held or pressed more than once, the player will continue moving backward or forward through the CD.
Page 180 To play the song list, press the SONG LIST button. One beep will be heard and S-LIST will appear on the display. The recorded tracks will begin to play in the order they were saved. Seek through the song list by using the SEEK or TYPE arrows.
Page 181: Theft-Deterrent Feature (Non-Rds Radios)
CD Messages CHECK CD: If this message appears on the display and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. •...
Page 182: Radio Reception
Radio Reception The range for most AM stations is greater than for FM, especially at night. The longer range, however, can cause stations to interfere with each other. AM can pick up noise from things like storms and power lines. Try reducing the treble to reduce this noise.
Page 183 When cleaning the cassette tape player with the recommended non-abrasive cleaning cassette, it is possible that the cassette may eject, because the cut tape detection feature on the radio may recognize it as a broken tape, in error. To prevent the cleaning cassette from being ejected, use the following steps: 1.
Page 184: Care Of Your Cds
Care of Your CDs Handle CDs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a CD is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
Page 185: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunken Driving ...4-2 Control of a Vehicle ...4-5 Braking ...4-5 Anti-Lock Brake System (ABS) ...4-6 Braking in Emergencies ...4-7 Locking Rear Axle ...4-7 ® StabiliTrak System ...4-8 Steering ...4-10 Off-Road Recovery ...4-12 Passing ...4-12...
Page 186: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-10. Defensive driving really means “be ready for anything.”...
Page 187 Many adults — by some estimates, nearly half the adult population — choose never to drink alcohol, so they never drive after drinking. For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological and developmental reasons for these laws.
Page 188 There is a gender difference, too. Women generally have a lower relative percentage of body water than men. Since alcohol is carried in body water, this means that a woman generally will reach a higher BAC level than a man of her same body weight will when each has the same number of drinks.
Page 189: Control Of A Vehicle
CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Please do not drink and drive or ride with a driver who has been drinking.
Page 190: Anti-Lock Brake System (Abs)
If you keep pace with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking. That means better braking and longer brake life. If your engine ever stops while you are driving, brake normally but do not pump your brakes. If you do, the pedal may get harder to push down.
Page 191: Braking In Emergencies
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. As you brake, your computer keeps receiving updates on wheel speed and controls braking pressure accordingly.
Page 192: Stabilitrak System
® StabiliTrak System ® If your vehicle has StabiliTrak , it combines anti-lock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions. When you ﬁrst start your vehicle and begin to drive away, the system performs several diagnostic checks to ensure that it is working properly.
Page 193 Pressing and holding the StabiliTrak on the instrument panel for more than ﬁve seconds can turn off StabiliTrak and part of the traction control system. For your safety, the system can only be disabled when the vehicle speed is less than 20 mph (32 km/h). You will hear three chimes and the StabiliTrak ready light will come on.
Page 194: Steering
Traction Control Operation The traction control system is part of the StabiliTrak system. Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary. If the brake-traction control system activates constantly or if the brakes have heated up due to high speed braking, the brake-traction control will be automatically...
Page 195: Steering In Emergencies
Speed limit signs near curves warn that you should adjust your speed. Of course, the posted speeds are based on good weather and road conditions. Under less favorable conditions you will want to go slower. If you need to reduce your speed as you approach a curve, do it before you enter the curve, while your front wheels are straight ahead.
Page 196: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you are driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 197 • Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Page 198: Loss Of Control
Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked.
Page 199: Driving At Night
Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving. •...
Page 200: Driving In Rain And On Wet Roads
You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to re-adjust to the dark. When you are faced with severe glare, as from a driver who does not lower the high beams, or a vehicle with misaimed headlamps, slow down a little.
Page 201 The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking.
Page 202: Driving Through Flowing Water
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Page 203: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: •...
Page 204: Freeway Driving
Freeway Driving Mile for mile, freeways—also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 205: Before Leaving On A Long Trip
Before Leaving on a Long Trip Make sure you are ready. Try to be well rested. If you must start when you are not fresh — such as after a day’s work — do not plan to make too many miles that ﬁrst part of the journey.
Page 206: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or mountains is different from driving in ﬂat or rolling terrain. 4-22 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable.
Page 207 CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they would not work well. You would then have poor braking or even none going down a hill.
Page 208: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Also see Tires on page 5-52. 4-24 Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and reﬂective warning triangles.
Page 209 What is the worst time for this? Wet ice. Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get wet ice when it is about freezing (32°F;...
Page 210: If You Are Caught In A Blizzard
If You Are Caught in a Blizzard If you are stopped by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. Here are some things to do to summon help and keep yourself and your passengers safe: •...
Page 211 CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 212: If You Are Stuck: In Sand, Mud, Ice Or Snow
If You Are Stuck: In Sand, Mud, Ice or Snow In order to free your vehicle when it is stuck, you will need to spin the wheels, but you do not want to spin your wheels too fast. The method known as rocking can help you get out when you are stuck, but you must use caution.
Page 213: Loading Your Vehicle
Loading Your Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo and all nonfactory-installed options. Two labels on your vehicle show how much weight it was designed to carry, the Tire and Loading Information label and the Certiﬁcation/Tire label.
Page 214 The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inﬂation pessures (D). For more information on tires and inﬂation see Tires on page 5-52 and Inﬂation - Tire Pressure on page 5-58. There is also important loading information on the vehicle Certiﬁcation/Tire label.
Page 215 Example 1 Item Description Vehicle Capacity Weight for Example 1 Subtract Occupant Weight 150 lbs (68 kg) Available Occupant and Cargo Weight Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Vehicle Capacity Weight 1,000 lbs (453 kg) for Example 2 Subtract Occupant...
Page 216 Example 3 Item Description Vehicle Capacity Weight for Example 3 Subtract Occupant Weight 200 lbs (91 kg) Available Cargo Weight Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers and cargo should never exceed your vehicle’s capacity weight.
Page 217: Add-On Equipment
The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To ﬁnd out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this.
Page 218: Towing
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-6. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing”...
Page 219: If You Do Decide To Pull A Trailer
If yours was built with trailering options, as many are, it’s ready for heavier trailers. But trailering is different than just driving your vehicle by itself. Trailering means changes in handling, durability and fuel economy. Successful, safe trailering takes correct equipment, and it has to be used properly.
Page 220: Weight Of The Trailer
Tow/Haul Mode Tow/haul is designed to assist while your vehicle is pulling a large or heavy load or trailer. Tow/haul is most useful while pulling such a load in rolling terrain, in stop-and-go traffic, or when you need improved low-speed control, such as when parking. The purpose of the tow/haul mode is to: •...
Page 221 The following chart shows how much your trailer can weigh, based upon vehicle model and options. Vehicle Axle Ratio G1500 Cargo Van 2WD 4300 V6 3.42 3.42 5300 V8 3.73 Vehicle Axle Ratio H1500 Cargo Van AWD 3.42 5300 V8 3.73 Vehicle Axle Ratio...
Page 222 Vehicle Axle Ratio G2500 Cargo Van 2WD 4300 V6 3.73 3.73 4800 V8 4.10 5300 V8 3.73 3.73 6000 V8 4.10 Vehicle Axle Ratio H2500 Cargo Van AWD 5300 V8 3.73 Vehicle Axle Ratio G2500 Cargo Van 2WD Long Wheelbase 4300 V6 3.73 3.73...
Page 223 Vehicle Axle Ratio G2500 Passenger Van 2WD Long Wheelbase 3.73 6000 V8 4.10 Vehicle Axle Ratio G3500 Cargo Van 2WD Short Wheelbase 3.73 6000 V8 4.10 Vehicle Axle Ratio G3500 Cargo Van 2WD Long Wheelbase 3.73 6000 V8 4.10 Vehicle Axle Ratio G3500 Passenger Van 2WD Short Wheelbase 3.73...
Page 224: Weight Of The Trailer Tongue
The Gross Combined Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo equipment and conversion. The GCWR for your vehicle should not be exceeded. You can ask your dealer for our trailering information or advice, or you can write us at the address listed in your Warranty and Owner Assistance Information Booklet.
Page 225 Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires. You’ll ﬁnd these numbers on the Certiﬁcation label at the rear edge of the driver’s door or see Loading Your Vehicle on page 4-29. Then be sure you don’t go over the GVW limit for your vehicle, or the GAWR, including the weight of the trailer tongue.
Page 226: Safety Chains
If you’ll be pulling a trailer that, when loaded, will weigh more than 5,000 lbs (2 270 kg), be sure to use a properly mounted weight-distributing hitch and sway control of the proper size. This equipment is very important for proper vehicle loading and good handling when you’re driving.
Page 227: Driving With A Trailer
Driving with a Trailer CAUTION: If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You can not see or smell CO. It can cause unconsciousness or death. See Engine Exhaust on page 2-27.
Page 228: Turn Signals When Towing A Trailer
Passing You’ll need more passing distance up ahead when you’re towing a trailer. And, because you’re a good deal longer, you’ll need to go much farther beyond the passed vehicle before you can return to your lane. Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, just move that hand to the left.
Page 229: Driving On Grades
Driving On Grades Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you don’t shift down, you might have to use your brakes so much that they would get hot and no longer work well. You can tow in DRIVE (D).
Page 230 When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3.
Page 231: Service And Appearance Care
Section 5 Service ...5-3 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of Your Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-5 California Fuel ...5-6 Additives ...5-6 Fuels in Foreign Countries ...5-7 Filling Your Tank ...5-8 Filling a Portable Fuel Container ...5-10 Checking Things Under the Hood ...5-10 Hood Release ...5-11...
Page 232 Section 5 Buying New Tires ...5-62 Uniform Tire Quality Grading ...5-63 Wheel Alignment and Tire Balance ...5-64 Wheel Replacement ...5-65 Tire Chains ...5-66 If a Tire Goes Flat ...5-67 Changing a Flat Tire ...5-68 Removing the Spare Tire and Tools ...5-69 Removing the Flat Tire and Installing the Spare Tire ...5-72 Secondary Latch System ...5-77...
Page 233: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 234: Doing Your Own Service Work
Doing Your Own Service Work If you want to do some of your own service work, you will want to use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-11.
Page 235: Adding Equipment To The Outside Of Your
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it. This may cause wind noise and affect windshield washer performance. Check with your dealer before adding equipment to the outside of your vehicle.
Page 236: California Fuel
California Fuel If your vehicle is certiﬁed to meet California Emission Standards (see the underhood emission control label), it is designed to operate on fuels that meet California speciﬁcations. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal speciﬁcations, but emission control system performance may be affected.
Page 237: Fuels In Foreign Countries
Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines may be available in your area to contribute to clean air. General Motors recommends that you use these gasolines, particularly if they comply with the speciﬁcations described earlier. Notice: Your vehicle was not designed for fuel that contains methanol.
Page 238: Filling Your Tank
Filling Your Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 239 CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Page 240: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 241: Hood Release
Hood Release To open the hood, do the following: 1. Pull the handle with this symbol on it. It is located in front of the driver’s side door frame near the ﬂoor. 2. Then go to the front of the vehicle and lift up the secondary hood release, which is located underneath the middle of the hood.
Page 242: Engine Compartment Overview
Engine Compartment Overview When you lift the hood, here is what you will see: 5-12...
Page 243: Engine Oil
A. Battery. See Battery on page 5-37. B. Radiator Pressure Cap. See Radiator Pressure Cap on page 5-24. C. Coolant Recovery Tank. See Cooling System on page 5-26. D. Automatic Transmission Fluid Dipstick. See “Checking the Fluid Level” under Automatic Transmission Fluid on page 5-19.
Page 244: When To Add Engine Oil
When to Add Engine Oil If the oil is at or below the cross-hatched area at the tip of the dipstick, then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use.
Page 245 • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. Oils meeting these requirements should also have the starburst symbol on the container.
Page 246: Engine Oil Life System
® GM Goodwrench oil meets all the requirements for your vehicle. If you are in an area of extreme cold, where the temperature falls below 20°F ( 29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil. Both will provide easier cold starting and better protection for your engine at extremely low temperatures.
Page 247: Engine Air Cleaner/Filter
To reset the change engine oil light, do the following: 1. Turn the ignition key to RUN with the engine off. 2. Fully press and release the accelerator pedal slowly three times within ﬁve seconds. 3. If the Change Engine Oil light ﬂashes for ﬁve seconds, the system is reset.
Page 248 When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace at the ﬁrst oil change after 50,000 miles (83 000 km). See Scheduled Maintenance on page 6-4 for more information. If you are driving in dusty/dirty conditions, inspect the ﬁlter at each engine oil change.
Page 249: Automatic Transmission Fluid
Automatic Transmission Fluid When to Check and Change A good time to check your automatic transmission ﬂuid level is when the engine oil is changed. Change both the ﬂuid and ﬁlter every 50,000 miles (83,000 km) if the vehicle’s GVWR is over 8,600 or if the vehicle is mainly driven under one or more of these conditions: •...
Page 250 To get the right reading, the ﬂuid should be at normal operating temperature, which is 180°F to 200°F (82°C to 93°C). Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above 50°F (10°C). If it is colder than 50°F (10°C), drive the vehicle in DRIVE (D) until the engine temperature gage moves and then remains steady for 10 minutes.
Page 251 Then, without shutting off the engine, follow these steps: The transmission dipstick is located near the center of the engine compartment and will be labeled with the graphic shown. See Engine Compartment Overview on page 5-12 for more information on location. •...
Page 252: Engine Coolant
How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transmission ﬂuid to use. See Recommended Fluids and Lubricants on page 6-13. Using a funnel, add ﬂuid down the transmission dipstick tube only after checking the transmission ﬂuid while it is hot.
Page 253 What to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 254: Radiator Pressure Cap
Adding Coolant If you need more coolant, add the proper DEX-COOL coolant mixture at the coolant recovery tank, but be careful not to spill it. CAUTION: Turning the radiator pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly.
Page 255: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 256: Cooling System
If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traffic, let the engine idle in NEUTRAL (N) while stopped. If it is safe to do so, pull off the road, shift to PARK (P) or NEUTRAL (N) and let the engine idle.
Page 257 When the engine is cold, the coolant level should be at or above the COLD FILL mark. If it is not, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.
Page 258 How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet, but the coolant level is not at the COLD FILL mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL coolant at the coolant recovery tank. See Engine Coolant on page 5-22 for more information.
Page 259 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. When the coolant in the coolant recovery tank is at the COLD FILL mark, start your vehicle.
Page 260: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise until it ﬁrst stops. Do not press down while turning the pressure cap.
Page 261 4. Then ﬁll the coolant recovery tank to the COLD FILL mark. 5. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off. 6. Start the engine and let it run until you can feel the upper radiator hose getting hot.
Page 262: Engine Fan Noise
Engine Fan Noise Your vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions, the fan is spinning slower and the clutch is not fully engaged.
Page 263: Windshield Washer Fluid
3. Unscrew the cap and wipe the dipstick with a clean rag. 4. Replace the cap and completely tighten it. 5. Then remove the cap again and look at the ﬂuid level on the dipstick. The level should be at the COLD FILL mark. If necessary, add only enough ﬂuid to bring the level up to the mark.
Page 264: Brakes
Brakes Brake Fluid Your brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear.
Page 265 Checking Brake Fluid You can check the brake ﬂuid without taking off the cap. Look at the brake ﬂuid reservoir. The ﬂuid level should be above MIN. If it is not, have your brake system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark.
Page 266: Brake Wear
Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.
Page 267: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts.
Page 268: Jump Starting
Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative ( ) cable from the battery. This will help keep your battery from running down. CAUTION: Batteries have acid that can burn you and gas that can explode.
Page 269 Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
Page 270 4. Open the hoods and locate the positive (+) and negative ( ) terminal locations of the other vehicle. Your vehicle has a remote positive (+) jump starting terminal and a remote negative ( ) jump starting terminal. You should always use these remote terminals instead of the terminals on the battery.
Page 271 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one.
Page 272 8. Now connect the black negative ( ) cable to the negative ( ) terminal of the good battery. Use a remote negative ( ) terminal if the vehicle has one. Do not let the other end touch anything until the next step.
Page 273: All-Wheel Drive
3. Disconnect the red positive (+) cable from the vehicle with the good battery. 4. Disconnect the red positive (+) cable from the other vehicle. 5. Return the remote positive (+) terminal cover to its original position. All-Wheel Drive Lubricant checks in this section also apply to these vehicles.
Page 274: Rear Axle
Rear Axle When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See Scheduled Maintenance on page 6-4. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 275: Noise Control System
If the level is below the bottom of the ﬁller plug hole, you may need to add some lubricant. When the differential is cold, add enough lubricant to raise the level to 3/8 inch (10 mm) below the ﬁller plug hole. When the differential is at operating temperature (warm), add enough lubricant to raise the level to the bottom of the ﬁller plug hole.
Page 276: Bulb Replacement
Federal law prohibits the following acts or the causing thereof: 1. The removal or rendering inoperative by any person, other than for purposes of maintenance, repair or replacement, of any device or element of design incorporated into any new vehicle for the purpose of noise control, prior to its sale or delivery to the ultimate purchaser or while it is in use;...
Page 277: Halogen Bulbs
Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package. Headlamps To remove the headlamp assembly from the vehicle and access the bulbs, do the following: 1.
Page 278: Front Turn Signal, Sidemarker And Parking Lamps
10. Turn the bulb counterclockwise one quarter turn to remove it from the socket. 11. On the passenger’s side, turn the bulb clockwise one turn. Do not touch the glass part of the bulb. 12. Install the new bulb into the socket then reinstall it into the headlamp assembly.
Page 279: Center High-Mounted Stoplamp (Chmsl)
Center High-Mounted Stoplamp (CHMSL) Your vehicle’s center high-mounted stoplamp (CHMSL) is located above the rear doors at the center of the vehicle. 1. Remove the screws from the CHMSL assembly. 2. Remove the assembly. 3. Turn the bulb counterclockwise one quarter turn to remove it from the socket.
Page 280: Replacement Bulbs
7. Remove the taillamp bulb socket by squeezing the tab on the side of the socket while turning it counterclockwise. 8. Turn the bulb counterclockwise to remove it. 9. Install a new bulb. 10. Reverse the steps to reinstall the lamp assemblies. 5-50 Replacement Bulbs Exterior Lamp...
Page 281: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear and cracking. See Scheduled Maintenance on page 6-4 for more information on wiper blade inspection. Replacement blades come in different types and are removed in different ways.
Page 282: Tires
4. To install the new wiper insert, slide the notched end last, into the end with two blade claws. Then slide the insert all the way through the blade claws at the opposite end. 5. Make sure that the notches are locked by the bottom claws.
Page 283: Tire Sidewall Labelling
Tire Sidewall Labelling Useful information about a tire is molded into the sidewall. The following illustrations are examples of a typical P-Metric and a LT-Metric tire sidewall. Passenger (P-Metric) Tire (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description.
Page 284 Light Truck (LT-Metric) Tire (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC...
Page 285: Tire Size
Tire Size The following examples show the different parts of a tire size. Passenger (P-Metric) Tire Light Truck (LT-Metric) Tire (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
Page 286: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kiloPascal (kPa). Accessory Weight: This means the combined weight of optional accessories.
Page 287 Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. KiloPascal (kPa): The metric unit for air pressure. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.
Page 288: Inﬂation - Tire Pressure
Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called “wear bars,” that show across the tread of a tire when only 1/16 inch (1.6 mm) of tread remains. See When It Is Time for New Tires on page 5-62. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear.
Page 289: Dual Tire Operation
A Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar), below the driver’s door latch. This label shows your vehicle’s original equipment tires and the correct inﬂation pressures for your tires when they are cold. The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity.
Page 290: Tire Inspection And Rotation
The outer tire on a dual wheel setup generally wears faster than the inner tire. Your tires will wear more evenly and last longer if you rotate the tires periodically. See Tire Inspection and Rotation on page 5-60. Also see Scheduled Maintenance on page 6-4. CAUTION: If you operate your vehicle with a tire that is badly underinﬂated, the tire can overheat.
Page 291 Dual Rear Wheels If your vehicle has dual rear wheels, always use one of the correct rotation patterns shown here when rotating your tires. When you install dual wheels, be sure that vent holes in the inner and outer wheels on each side are lined up. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label.
Page 292: When It Is Time For New Tires
When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. Some commercial truck tires may not have treadwear indicators.
Page 293: Uniform Tire Quality Grading
CAUTION: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias-belted tires) the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle.
Page 294: Wheel Alignment And Tire Balance
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 295: Wheel Replacement
Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist.
Page 296: Tire Chains
Used Replacement Wheels CAUTION: Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
Page 297: If A Tire Goes Flat
Notice: If your vehicle does not have dual wheels and is equipped with a tire size other than P235/75R16 or LT245/75R16, use tire chains only where legal and only when you must. Use chains that are the proper size for your tires. Install them on the tires of the rear axle.
Page 298: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning ﬂashers. CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Page 299: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools If you have a cargo van or a passenger van, the equipment you will need is located in the passenger side rear corner of the vehicle. Remove the retaining wing bolt and lift it off the mounting bracket.
Page 300 The tools you will be using include the jack (A), jack handle extension (B), jack handle (C), wheel wrench (D) and the ratchet (E). Your spare tire is stored underneath the rear of your vehicle. You will use the wheel wrench (D) and the ratchet (E) to lower the spare tire from the vehicle.
Page 301 3. Turn the ratchet counterclockwise to lower the spare tire to the ground. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower. See Secondary Latch System on page 5-77. 4.
Page 302: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire If your vehicle has plastic wheel nut caps, loosen them by turning the wheel wrench counterclockwise. The wheel nut caps are designed to remain with the center cap. Remove the center cap. If the wheel has a smooth center piece, place the chisel end of the wheel wrench in the slot on the wheel and gently pry it out.
Page 303 Connect the jack handle (B) and jack handle extension (C) together and press the retention clip (arrow) so it engages. Front Position 5-73...
Page 304 3. Position the jack under the vehicle as shown. Rear Position CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.
Page 305 4. Raise the vehicle by turning the ratchet clockwise. Make sure the UP mark faces you. Raise the vehicle far enough off the ground so there is enough room for the spare tire to ﬁt. 5. Remove all the wheel nuts, and take off the ﬂat tire.
Page 306 CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle.
Page 307: Secondary Latch System
CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts.
Page 308 See Storing a Flat or Spare Tire and Tools on page 5-80 for instructions on storing the spare tire correctly. CAUTION: Before beginning this procedure read all the instructions. Failure to read and follow the instructions could damage the hoist assembly and you and others could get hurt.
Page 309 3. Connect the jack handle (C) and jack handle extension (B) together and press the retention clip (arrow) so it engages. 4. Attach the jack handle/jack handle extension to the jack. With the UP mark facing you, slide the ratchet onto the end of the jack handle extension.
Page 310: Storing A Flat Or Spare Tire And Tools
8. Disconnect the jack handle from the jack and carefully remove the jack. Use one hand to push against the spare while ﬁrmly pulling the jack out from under the spare tire with the other hand. If the spare tire is hanging from the cable, slide the ratchet onto the wheel wrench and insert the wheel wrench into the hoist shaft hole above the bumper.
Page 311 2. Pull the retaining bar through the center of the wheel, making sure it is properly attached. 3. Pull the wheel toward the rear of the vehicle, keeping the cable tight. 4. With the UP side facing you, attach the ratchet to the wheel wrench.
Page 312: Spare Tire
6. Raise the tire fully against the underside of the vehicle. Continue turning the ratchet until the tire is secure and the cable is tight. The spare tire hoist cannot be overtightened. 7. Make sure the tire is stored securely. Push, pull, and then try to rotate or turn the tire.
Page 313: Fabric/Carpet
Never use these to clean the vehicle: • Gasoline • Benzene • Naphtha • Carbon Tetrachloride • Acetone • Paint Thinner • Turpentine • Lacquer Thinner • Nail Polish Remover They can all be hazardous — some more than others — and they can all damage the vehicle, too. Do not use any of these products unless this manual says you can.
Page 314: Special Fabric Cleaning Problems
3. Clean the entire area. Avoid getting the fabric too wet. 4. Start cleaning from the seams into the stain to avoid a ring effect. 5. Continue cleaning, using a clean area of the cloth each time it becomes soiled. 6.
Page 315: Vinyl
Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. This may have to be done more than once. • Things like tar, asphalt, and shoe polish will stain if they are not removed quickly. Use a clean cloth and vinyl cleaner.
Page 316: Weatherstrips
Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 6-13. Washing Your Vehicle The paint ﬁnish on the vehicle provides beauty, depth of color, gloss retention, and durability.
Page 317: Windshield And Wiper Blades
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s ﬁnish if they remain on painted surfaces. Wash the vehicle as soon as possible.
Page 318: Aluminum Wheels
Aluminum Wheels Notice: If you use strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only GM-approved cleaners on aluminum or chrome-plated wheels.
Page 319: Sheet Metal Damage
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.
Page 320: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products. Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Oil Removes tar, road oil, Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel.
Page 321: Vehicle Identiﬁcation Number (Vin)
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 322: Electrical System
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 323: Floor Console Fuse Block
Floor Console Fuse Block The ﬂoor console fuse block is located under the driver’s seat. Fuse Spare Outside Rear View Mirror Courtesy Lamp/SEO Usage Fuse Usage Left Rear Stop/Turn Signal Cargo Locks Right Rear Stop/Turn Signal Driver Locks Stop/Center High Mounted Stop Lamp Climate Control 1 Climate Control...
Page 324: Engine Compartment Fuse Block
Fuse Trailer Park Lamp Front Park Lamp Auxilary 1 Auxilary 2 Relays Usage Window Residual Accessory Power Auxiliary Right Rear Defogger Courtesy Lamp Cargo Unlock Driver Unlock Park Lamp Door Locks Passenger Unlock Circuit Breaker Power Window 5-94 Engine Compartment Fuse Block Usage The fuse block is located in the engine compartment on the driver’s side of the vehicle.
Page 325 Fuse Usage Ignition 0 Stoplamp Right Rear Defogger/Heated Mirror Right Daytime Running Lamp/Turn Signal Left Daytime Running Lamp/Turn Signal Truck Body Control Module 4 Fuel Pump Trailer Flasher Horn Truck Body Control Module 3 Trailer Stop/Turn Signal Truck Body Control Module 2 Truck Body Control Module Remote Function Actuator Engine 2...
Page 326 Fuse Powertrain Control Module Ignition 1 Oxygen Sensor B Oxygen Sensor A Windshield Wipers Right Headlamp - Low Beam Left Headlamp - Low Beam Left Headlamp - High Beam Right Headlamp - High Beam Truck Body Control Module-Accessory Front Windshield Wiper Anti-Lock Brakes Ignition A Trailer...
Page 327: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-13 for more information. When adding, be sure to ﬁll to the appropriate level or as recommended in this manual. See refrigerant charge label under the hood for charge capacity information and requirements.
Page 328 Application Fuel Tank Standard Tank (Passenger and Cargo) Standard Tank (Cab and Chassis) Optional Tank (Cab and Chassis)* * 159 inch (4 039 mm) wheelbase or 177 inch (4 496 mm) wheel base only Wheel Nut Torque All capacities are approximate. When adding, be sure to ﬁll to the approximate level, as recommended in this manual.
Page 329 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using Your Maintenance Schedule ...6-3 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-8 Owner Checks and Services ...6-10 Maintenance Schedule At the First 100, 1,000 and 6,000 Miles (160, 1 600 and 10 000km) ...6-10 At Each Fuel Fill ...6-10 At Least Once a Month ...6-10...
Page 330: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended ﬂuids and...
Page 331: Using Your Maintenance Schedule
Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather.
Page 332: Scheduled Maintenance
Owner Checks and Services on page 6-10 tells you what should be checked, when to check it and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, ﬂuids and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-13 and Normal Maintenance Replacement Parts on page 6-15.
Page 333 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-13. Reset oil life system. See Engine Oil Life System on page 5-16. An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage.
Page 334: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 335 Additional Required Services (cont’d) 25,000 50,000 75,000 100,000 125,000 150,000 Service and Miles (Kilometers) (41 500) (83 000) (125 000) (166 000) (207 500) (240 000) Replace spark plugs and inspect spark plug wires. An Emission Control Service. Engine cooling system service (or every 5 years, whichever occurs ﬁrst).
Page 336: Maintenance Footnotes
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
Page 337 (g) Vehicles with GVWR above 10,000 lbs (4 536 kg) only: Inspect shields for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable only to vehicles sold in the United States. (h) Change automatic transmission ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: −...
Page 338: Owner Checks And Services
Owner Checks and Services These owner checks and services should be performed at the intervals speciﬁed to help ensure the safety, dependability and emission control performance of your vehicle. Your GM Goodwrench dealer can assist you with these checks and services. Be sure any necessary repairs are completed at once.
Page 339: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle.
Page 340: Ignition Transmission Lock Check
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK in each shift lever position. • The ignition should turn to LOCK only when the shift lever is in PARK (P). •...
Page 341: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines starburst symbol.
Page 342 Usage Fluid/Lubricant Chassis Lubricant (GM Part No. U.S. 12377985, in Chassis Canada 88901242) or lubricant Lubrication meeting requirements of NLGI #2, Category LB or GC-LB. Wheel bearing lubricant meeting Front Wheel requirements of NLGI #2, Category Bearings GC or GC-LB (GM Part No. U.S.
Page 343: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained by your GM dealer. Part Engine Air Cleaner/Filter Engine Oil Filter 4300 V6 4800 V8, 5300 V8, 6000 V8 Passenger Compartment Air Filter Kit PCV Valve —...
Page 344: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-10 can be added on the following record pages.
Page 345 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 346 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 347 Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-3 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Reimbursement Program ...7-5 Roadside Assistance Program ...7-6 Courtesy Transportation ...7-7 Vehicle Data Collection and Event Data Recorders ...7-9 Customer Assistance and Information Reporting Safety Defects ...7-10...
Page 348: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 349: Online Owner Center
The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to ﬁling a court action, use of the program is free of charge and your case will generally be heard within...
Page 350: Customer Assistance For Text Telephone (Tty) Users
Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. If a U.S. customer wishes to write to Chevrolet, the letter should be addressed to Chevrolet’s Customer Assistance Center. United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 351: Gm Mobility Reimbursement Program
Canada — Customer Assistance General Motors of Canada Limited Customer Communication Centre, 163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800 Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S.
Page 352: Roadside Assistance Program
Roadside Assistance Program As the owner of a new Chevrolet vehicle, you are automatically enrolled in the Chevrolet Roadside Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road. Call Chevrolet’s...
Page 353: Courtesy Transportation
Roadside Assistance is not part of or included in the coverage provided by the New Vehicle Limited Warranty. Chevrolet reserves the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 354: Transportation Options
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, Chevrolet helps minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following:...
Page 355: Vehicle Data Collection And Event Data Recorders
Courtesy Transportation is available only at participating GM dealers and all program options, such as shuttle service, may not be available at every dealer. Please contact your GM dealer for speciﬁc information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel.
Page 356: Reporting Safety Defects
Unlike the data recorders on many airplanes, these on-board systems do not record sounds, such as conversation of vehicle occupants. To read this information, special equipment is needed and access to the vehicle or the device that stores the data is required. GM will not access information about a crash event or share it with others other than: •...
Page 357: Reporting Safety Defects To The Canadian Government
General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you will notify General Motors. Please call the Chevrolet Customer Assistance Center at 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 358: Current And Past Model Order Forms
Transmission, Transaxle, Transfer Case Unit Repair Manual This manual provides information on unit repair service procedures, adjustments, and speciﬁcations for GM transmissions, transaxles, and transfer cases. Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks.
Page 359 Accessory Power Outlets ... 3-16 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-70 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-92 Air Cleaner/Filter, Engine ... 5-17 Air Conditioning ... 3-18 Airbag Off Light ... 3-26 Readiness Light ... 3-25 Airbag Sensing and Diagnostic Module (SDM) ...
Page 360 Audio System(s) (cont.) Setting the Time for Radios with Radio Data Systems (RDS) ... 3-40 Setting the Time for Radios without Radio Data Systems (RDS) ... 3-40 Theft-Deterrent Feature ... 3-71 Understanding Radio Reception ... 3-72 Automatic Transmission Fluid ... 5-19 Operation ...
Page 361 Child Restraints Child Restraint Systems ... 1-39 Infants and Young Children ... 1-33 Lower Anchorages and Top Tethers for Children (LATCH System) ... 1-49 Older Children ... 1-31 Securing a Child Restraint Designed for the LATCH System ... 1-51 Securing a Child Restraint in a Center Seat Position ...
Page 362 Daytime Running Lamps ... 3-14 Daytime Running Lamps Indicator Light ... 3-37 Defensive Driving ... 4-2 Doing Your Own Service Work ... 5-4 Dome Lamp Override ... 3-15 Dome Lamps ... 3-15 Door 60/40 Swing-Out Side Door ... 2-12 Cargo Door Relocking ... 2-8 Locks ...
Page 363 Extender, Safety Belt ... 1-30 Exterior Lamps ... 3-13 Filter Engine Air Cleaner ... 5-17 Finish Damage ... 5-89 Fixed Mast Antenna ... 3-74 Flash-to-Pass ... 3-9 Flat Tire ... 5-67 Flat Tire, Changing ... 5-68 Flat Tire, Storing ... 5-80 Fluid Automatic Transmission ...
Page 364 Headlamps (cont.) Front Turn Signal, Sidemarker and Parking Lamps ... 5-48 Halogen Bulbs ... 5-47 High/Low Beam Changer ... 3-8 On Reminder ... 3-14 Heater ... 3-18 Highbeam On Light ... 3-37 Highway Hypnosis ... 4-21 Hill and Mountain Roads ... 4-22 Hood Checking Things Under ...
Page 365 Light (cont.) Brake System Warning ... 3-29 Change Engine Oil ... 3-35 Charging System ... 3-28 Check Gages Warning ... 3-38 Cruise Control ... 3-36 Daytime Running Lamps Indicator ... 3-37 Highbeam On ... 3-37 Malfunction Indicator ... 3-32 Reduced Engine Power ... 3-37 Safety Belt Reminder ...
Page 366 Mirrors (cont.) Outside Manual Mirror ... 2-29 Outside Power Mirrors ... 2-30 MyGMLink.com ... 7-3 New Vehicle Break-In ... 2-18 Noise Control System, Tampering ... 5-45 Normal Maintenance Replacement Parts ... 6-15 Odometer ... 3-24 Odometer, Trip ... 3-24 Off-Road Recovery ... 4-12 Change Engine Oil Light ...
Page 367 Questions and Answers About Safety Belts ... 1-14 Radiator Pressure Cap ... 5-24 Radios ... 3-39 AM-FM Radio ... 3-40 Care of Your Cassette Tape Player ... 3-72 Care of Your CD Player ... 3-74 Care of Your CDs ... 3-74 Radio with Cassette and CD ...
Page 368 Retained Accessory Power (RAP) ... 2-19 Right Front Passenger Position, Safety Belts ... 1-23 Roadside Assistance Program ... 7-6 Rocking Your Vehicle to Get it Out ... 4-28 Running Your Engine While You Are Parked ... 2-28 Safety Belt Pretensioners ... 1-30 Reminder Light ...
Page 369 Signals, Turn and Lane-Change ... 3-8 Sliding Side Door ... 2-10 Spare Tire ... 5-82 Installing ... 5-72 Removing ... 5-69 Storing ... 5-80 Speciﬁcations, Capacities ... 5-97 Speedometer ... 3-24 ® Stabilitrak System ... 4-8 ® Stabilitrak Indicator Light ... 3-31 ®...
Page 370 Traction ® Stabilitrak System ... 4-8 Transmission Fluid, Automatic ... 5-19 Transmission Operation, Automatic ... 2-22 Trip Odometer ... 3-24 Turn and Lane-Change Signals ... 3-8 Turn Signal/Multifunction Lever ... 3-7 Understanding Radio Reception ... 3-72 Uniform Tire Quality Grading ... 5-63 Vehicle Control ...

This manual is also suitable for:

Express 2005

Chevrolet 2005 Express Van Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Front Seats

Rear Seats

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Storage Areas

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

All-Wheel Drive

Rear Axle

Front Axle

Noise Control System

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Chevrolet 2005 Express Van

Summary of Contents for Chevrolet 2005 Express Van