Page 1
ORDER NO.DSD0603003CE DVD Recorder DMR-EH55EC / DMR-EH55EP / DMR-EH56EG Vol. 1 Colour (S).......Silver Type (K).......Black Type SPECIFICATIONS...
2006 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Safety Precaution 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
chassis, the reading must be . Figure 1 1.1.2. Leakage current hot check / (See Figure 1 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5k , 10 watts resistor, in parallel with a 0.15 capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure...
Page 4
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
2.2. Precaution of Laser Diode 2.3. Service caution based on legal restrictions 2.3.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
- The lead free solder has to be used when repairing the equipment for which the lead free solder is used. (Definition: The letter of “PbF” is printed on the PCB using the lead free solder.) - To put lead free solder, it should be well molten and mixed with the original lead free solder.
5. New Feature 5.1. About DivX 5.1.1. General DivX is a new video compressing format that is applied MPEG4 technology to improve image quality and the compressibility, and it is developed by the DivXNetworks, Inc., Video file of high resolution and the high picture quality can be made though it is a high compressibility. DivX codec is necessary for converting video to DivX file and .playback files made.
Page 10
5.1.2. Operating Instructions about DivX Video-on-Demand Content DivX Video-on-Demand (VOD) content is encrypted for copyright protection. In order to play DivX VOD content on this unit, you first need to register the unit. Follow the on line instructions for purchasing DivX VOD content to enter unit's registration code and register unit.
Page 14
5.1.3. About DivX DRM Divx file includes file to which DRM(Digital Right Management) is applied and file not applied. This item is a content that relates only in treating file to which DRM is applied. 1. Registration Code display function 2.
Page 15
Moreover, Registration code is updated by new user authentication ever if same recorder. 2) User's registration and approval function - Only one user can register for one recorder. If user's registration is not done with the recorder, DivX file cannot be played back. - User's registration is performed only when a DivX DRM file is first chosen by recorder - DivX DRM file that can perform user's registration is only a file that...
Above mentioned stored user information and number of times of playback are not erased by update of firmware or by initialization by test mode. 6. Location of Controls and Components Followings are the Location of Controls and Components for DMR-EH55EC and DMR-EH56EG as a sample. For other model, refer to each Operation Instructions.
Page 17
5. Put deck upward, and push out Tray by Eject Pin (JZS0484) or minus screw driver (small).
8. Service Mode 8.1. Self-Diagnosis and Special Mode Setting 8.1.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U**, H** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
Page 19
Error Diagnosis contents Description Monitor Automatic FL display Code Display Remote control code Display appears when main unit No display error and remote controller codes are not matched. “*” is remote controller code of the main unit. Display for 5 seconds. Abnormal inner Display appears when the drive No display...
Page 20
Error Diagnosis contents Description Monitor Automatic FL display Code Display Hang-up Displayed when communication No display error has occurred between Main microprocessor and Timer microprocessor. Displayed is left until the [POWER] key is pressed. Inoperative fan motor When inoperative fan motor is No display No display detected after powered on, the...
Page 21
Error Diagnosis contents Description Monitor Automatic FL display Code Display Unsupported disc *An unsupported format disc “This disc is UNSUPPORT error was played, although the drive incompatible.” starts normally. *The data format is not supported, although the media type is supported. Display for 5 seconds.
Page 22
Error Diagnosis contents Description Monitor Automatic FL display Code Display Unit is in termination Unit is in termination process No display PLEASE process now. WAIT “BYE” is displayed and power will be turned off. In case “Quick Start” of setup menu is ON, it is displayed in restoration operation for AC off.
Page 23
Error Diagnosis contents Description Monitor Automatic FL display Code Display Power on Stand-by [HDD NG] is displayed when No display setting error power on Stand-by setting of HDD is NG or when HDD which power on Stand-by is not set to is used.
Page 24
Item FL display Key operation Mode name Description Front Key Forced disc eject Removing a disc that cannot be The display before When the power is off, ejected. execution leaves. press [STOP] and [CH UP] keys simultaneously for 5 The tray will open and unit will seconds.
Page 25
Item FL display Key operation Mode name Description Front Key Forced power-off When the power button is not Display in P-off mode. Press [Power] key over effective while power is ON, turn than 10 seconds. off the power forcibly. *When Timer REC is ON or EXT- LINK is ON, execute “Forced Power-off”...
Page 26
Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Display following the then When the power is ON, Aging Description shown below mode. press [STOP], [POWER] continually. and [OPEN/CLOSE] simultaneously for over 5 seconds and less than 10 seconds.
Page 28
Item FL display Key operation Mode name Description Front Key Demonstration Ejection of the disc is prohibited. *When lock the tray. When the power is on, lock/unlock press [STOP] and The lock setting is effective until [POWER] keys unlocking the tray and not simultaneously for 5 released by “Main unit seconds.
Page 29
Item FL display Key operation Mode name Description Front Key Progressive The progressive setting is The display before When the power is on (E- initialization initialized to Interlace. execution leaves. E mode), press [STOP] and [PLAY] simultaneously for 5 seconds. 8.1.3.
Page 30
Item FL display Key operation Mode name Description (Remote controller key) ROM Version 1. Region code (displayed for 5 Press [0] [2] in service Display sec.) mode 2. Main firm version (displayed for 5 sec.) 3. Timer firm version (displayed for 5 sec.) 4.
Page 31
Item FL display Key operation Mode name Description (Remote controller key) Magenta Picture Magenta picture is output with *Initial mode is “Interlace”. Press [1] [2] in service Output Component Output from AV mode. Decoder. *Magenta picture (Saturation rate: 100%) Switch Interlace/ Press [1] [4] in Magenta *It is enable to switch Interlace/ Progressive...
Page 32
Item FL display Key operation Mode name Description (Remote controller key) I/P Switch Switch Interlace and Progressive Initial mode is Interlace Press [1] [4] in I/P Switch in EE mode. mode. *Initial setting is “Interlace”. *I/P are switched alternately. *This command is effective during executing “White Picture Switch Interlace/ Output”, “Magenta Picture...
Page 33
Item FL display Key operation Mode name Description (Remote controller key) HDD READ Perform a complete read When the HDD is OK Press [3] [1] in service inspection inspection of the HDD. mode. *When canceling the checking mode while executing, do “forced If the HDD is defective power-off”.
Page 34
Item FL display Key operation Mode name Description (Remote controller key) Laser Used Time Check laser used time (hours) of Press [4] [1] in service Indiction drive. mode. (*****) is the used time display in hour. Laser used time of DVD / CD in Playback/ Recording mode is counted.
Page 35
Item FL display Key operation Mode name Description (Remote controller key) RAM Drive Last RAM Drive error code display. 1. Error Number is Press [4] [2] in service Error displayed for 5 seconds. mode. *For details about the drive error code, refer to the Service Manual When “INFO******”...
Page 36
seconds. 6. Disc Maker ID is displayed for 5 seconds. In case that the maker cannot be identified, display is black out. 7. Factor of Drive Error occurring is left displayed...
Page 37
Item FL display Key operation Mode name Description (Remote controller key) Delete the Last Delete the Last Drive Error Press [9] [6] in service Drive Error information stored on the DVD mode. RAM-Drive. Laser power Drive state is judged based on confirmation difference between laser power into RAM Drive in service mode.
Page 38
Item FL display Key operation Mode name Description (Remote controller key) Front connection Press all front keys and check Press [5] [4] in service inspection the connection between Main mode. P.C.B. and Front key Switches. (1) Each time a key is pressed, segment turned on increases one by one.
Page 39
Item FL display Key operation Mode name Description (Remote controller key) Display the Error Display the Error History stored Display reason of error for Press [6] [5] in service History on the unit. 5 seconds. mode. Then press [0] [1] ~ [1] [9], the past 19 error histories are displayed.
Page 40
DD: Day hh: Hour mm: Minute Accumulated working time till occuring of the error is left displayed. (Indicating unit: Second)
Page 41
Item FL display Key operation Mode name Description (Remote controller key) Delete the Error Delete Error History information Press [9] [7] in service History stored on the unit. mode. SD card WRITE Delete Error History information When the WRITE check is Insert a SD card to SD check stored on the unit.
Page 42
Item FL display Key operation Mode name Description (Remote controller key) AV2(RGB)/AV1(V) I Set input to AV2 (RGB) and set Press [8] [3] in service /O Setting output to AV1 (V) for I/O checking mode. P50(H) Output Timer Microprocessor IC7501-76 When OK.
Item FL display Key operation Mode name Description (Remote controller key) Initialize Service Last Drive Error, Error history Press [9] [9] in service and Error Codes stored on the mode. unit are initialized to factory setting. Finishing service Release Service Mode. Display in STOP (E-E) Press power button on mode...
10. Disassembly and Assembly Instructions 10.1. Disassembly Flow Chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below. 10.2.
Page 45
the Top Case a little and lift the Top Case in the direction of the arrows. 10.4. Front Panel 1. Unlock 6 tabs in (A) - (F) turn. Pull with the front panel in the direction of your side. 10.5. SD Card P.C.B. 1.
Page 46
10.6. RAM/Digital P.C.B. Module 1. Remove 1 FFC and Screws (A). 2. Lift up Digital P.C.B. slightly so to disconnect Connectors to remove Digital P.C.B.
Page 47
3. Put Digital P.C.B. on RAM Drive and remove RAM/Digital P.C.B. Module. Note: RAM/Digital P.C.B. Module as service part has no heat sink unit. Before returning to customer, heat sink unit should be installed on Digital P.C.B..
Page 48
10.7. DV Jack P.C.B. 1. Remove 1 Screw (A) to remove DV Jack P.C.B. 10.8. HDD...
Page 49
1. Remove ATAPI Connector and HDD Power Connector. 2. Remove 4 Screws (A) to remove HDD Angle with HDD.
Page 50
3. Put HDD with HDD Angle up and down inversely so as not to give a shock to HDD. 4. Remove 4 screws (A) remove HDD.
Page 51
10.9. Rear Panel 1. Disconnect Fan Connector. 2. Remove 6 Screws (A) and 1 Screw (B). 3. Unlock 2 Locking Tabs (A) to remove Rear Panel.
Page 52
10.9.1. Fan Motor 1. Disconnect Fan Connector and remove 2 Screws (A). 2. Push and unlock 2 Locking Tabs (A) to remove Fan Motor. 10.10. Power P.C.B. 1. Remove 1 Screw (A). 2. Remove 3 Screws (B) and disconnect Connector (A) to remove Power P.C.B..
Page 53
10.11. Main P.C.B. and Front (L) P.C.B. 1. Remove 1 Screw (A). 2. Remove 4 Screws (A) and 1 Screw (B). 3. Remove Digital Angle to remove Main P.C.B. and Front (L) P.C.B..
10.12. Tuner P.C.B. 1. Pull out the Tuner P.C.B. in the direction of the arrow. 11. Measurements and Adjustments 11.1. Service Positions Note: For description of the disassembling procedure, see the section 10. 11.1.1. Checking and Repairing of Power P.C.B.
Page 55
11.1.2. Checking and Repairing of RAM / Digital P.C.B. Module...
Page 56
11.1.3. Checking and Repairing of Main P.C.B.
11.2. Caution for Replacing Parts 11.2.1. Items that should be done after replacing parts...
Page 59
Note3: Please prepare latest firmware updating disc. * Main Firm is being recorded in HDD, but new HDD has no data. Writing Procedure of Main Firm: <<Caution>> (1) Writing of Main Firm needs 3, 4 minutes. (2) Never cut the power of DVD Recorder until writing in Firmware ends. (3) Initial settings and contents of reservation will not change if writing is normally completed.
3. Turn on power of DVD Recorder. 4. After [PLEASE WAIT] is displayed on FL., [HDD ERR] is displayed on FL. 5. Tray opens automatically. 6. Insert updating disc for Firmware and press OPEN/CLOSE key. (If a wrong disc was inserted, [NG DISK] [NO FVU] is displayed on FL.) 7.
Turn on the power, and confirm items pointed Items pointed out should reappear. out. Insert RAM disc. The Panasonic RAM disc should be recognized. Enter the EE (TU IN / AV IN - AV OUT) mode. No abnormality should be seen in the picture, sound or operation.
13.18. Front (L) Schematic Diagram 13.19. DV Jack Schematic Diagram 14. Printed Circuit Board 14.1. Power P.C.B. 14.2. Main P.C.B. 14.2.1. Main P.C.B. (1/4 Section) 14.2.2. Main P.C.B. (2/4 Section) 14.2.3. Main P.C.B. (3/4 Section) 14.2.4. Main P.C.B. (4/4 Section) 14.2.5.
Page 64
INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMP OUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT...
Page 65
INITIAL/LOGO ABBREVIATIONS DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROP OUT DOUT0~UP DATA OUTPUT DATA SLICE RF (BIAS) DROP OUT SIGNAL DRPOUT DATA REQUEST DREQ...
Page 66
INITIAL/LOGO ABBREVIATIONS IECOUT IEC958 FORMAT DATA OUTPUT IPFRAG INTERPOLATION FLAG IREF I (CURRENT) REFERENCE ISEL INTERFACE MODE SELECT LDON LASER DIODE CONTROL LASER POWER CONTROL LRCK L CH/R CH DISTINCTION CLOCK MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK...
Page 67
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
Page 68
SUB CODE Q DATA SYSCLK SYSTEM CLOCK INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSS SIGNAL TRON TRACKING ON TRSON...
INITIAL/LOGO ABBREVIATIONS X' TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPT REQUEST X' TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
16.2. Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts shown in the parts list.
Page 72
*Resistance values are in ohms, unless specified otherwise, 1K=1,000 (OHM), 1M=1,000k (OHM). *The marking (RTL) indicates the retention time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available. *“(IA)-(IH)”, marks in Remarks indicate languages of instruction manuals. [(IA): Polish, (IB): English, (IC): German, (ID): Italian, (IE): Dutch, (IF): French, (IG): Spanish, (IH): Swedish/ Danish] *Parts indicated with PAVC-CSG in the Remarks column are supplied by PAVC-CSG.
Ref. No. Part No. Part Name & Description Remarks RQT8421-J OPERATING INSTRUCTIONS (IH)ECS,ECK RQCC2704 DVD MEDIA SHEET RPG7863 PACKING CASE RPG8017 PACKING CASE RPG7862 PACKING CASE RPG7983 PACKING CASE RPG7910 PACKING CASE RPG7984 PACKING CASE RPN1859-1 CUSHION RPFD0004 MIRAMAT BAG RPN1903 FANBAG CUSHION ECS,ECK...
Page 99
Front (L) P.C.B. SD Card P.C.B. DMR-EH55EC/EP,EH56EG DMR-EH55EC/EP,EH56EG SD Card P.C.B. Front (L) P.C.B. (VEP73136A) (VEP70161A)
Page 100
DV Jack P.C.B. Tuner P.C.B. (EP) (EP) (EC/EG) (EC) DMR-EH55EC/EP,EH56EG Tuner P.C.B. ( VEP07A91B:EH55EC, DMR-EH55EC/EP,EH56EG VEP07A91D:EH55EP, DV JACK P.C.B. VEP07A91A:EH56EG) (VEP73135A)
Page 101
QR4003 XDMUTE UNR521100L (UN5211-TX) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH55EC/EP,EH56EG A/V I/O SECTION THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE (3/4) A/V I/O(1/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 102
LB3007 J0JBC0000011 C3059 1000P R4007 82K C3060 LB3008 470P J0JBC0000019 DMR-EH55EC/EP,EH56EG F G H N O P Q R S Z AA AB AC AD AE AG AH AI AJ AK AL AM A/V I/O SECTION A/V I/O(2/4) Section (4/4) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.
Page 103
DE:Nicam Decoder Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-EH55EC/EP,EH56EG T:Timer Section:(Page: SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. A/V I/O(3/4) Section (Main P.C.B.(2/4))
Page 104
LOCATION MAP M:Main Net Section:(Page: AV:A/V I/O Section:(Page: DE:Nicam Decoder Section:(Page: DMR-EH55EC/EP,EH56EG T:Timer Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. A/V I/O(4/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 105
100P(EXCEPT EG) R7317 AV:A/V I/O Section:(Page: DE:Nicam Decoder Section:(Page: T:Timer Section:(Page: DMR-EH55EC/EP,EH56EG Nicam Decoder Section NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. (Main P.C.B.(3/4)) THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 106
TPB- TPB+ TPB- NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH55EC/EP,EH56EG THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. DV Jack Schematic Diagram...
Page 107
(TIMER(4/4) SECTION) JW7001 [VWJ02F0060VV] KEY3_POWER NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH55EC/EP,EH56EG THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Front(L) Schematic Diagram...
Page 109
AV1 Lch MUTE IIC BUS (SW10) LOGIC BIAS AV2 R/C CLAMP TUN Rch TUNER AV2 G TUN Lch CLAMP CLAMP AV2 B CLAMP RF OUT MUTE AV2 V/Y CLAMP IC3001 Detail Block Diagram IC4011 Detail Block Diagram DMR-EH55EC/EP,EH56EG IC-Detail Block Diagram...
Page 110
Ref.No. Ref.No.50000,53000,54000, Digital 55000,57000 SERIES Main Net Ref.No.1500,7400 SERIES P.C.B. Main A/V I/O Ref.No.3000,3900,4000,4900 SERIES Audio I/O Ref.No.54000 SERIES RESET- P.C.B. Nicam Decoder Ref.No.7300 SERIES D Net/EPG Ref.No.59000 SERIES Timer Ref.No.7500 SERIES Model Select Ref.No.59000 SERIES DMR-EH55EC/EP,EH56EG Interconnection Schematic Diagram...
Page 112
THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE K7403 VWJ0795=10 SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. C7439 Q7402 2SD1819A0L R7446 2000[D] UNREG_38V DMR-EH55EC/EP,EH56EG Main Net(2/4) Section MAIN NET SECTION (4/4) (Main P.C.B.(1/4)) Schematic Diagram(M)
Page 113
AV:A/V I/O Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-EH55EC/EP,EH56EG DE:Nicam Decoder Section:(Page: SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Main Net(3/4) Section T:Timer Section:(Page: (Main P.C.B.(1/4))
Page 114
K9ZZ00001279 LOCATION MAP M:Main Net Section:(Page: AV:A/V I/O Section:(Page: DMR-EH55EC/EP,EH56EG DE:Nicam Decoder Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. Main Net(4/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE T:Timer Section:(Page: SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 115
V5/PWON VREF/SS TIMER OCP THRESHOLD COMPARATOR ON WIDTH TIMER DMR-EH55EC/EP,EH56EG IMPORTANT SAFETY NOTICE: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. SOURCE COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. /OCL THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Power Supply Schematic Diagram WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE.
Page 116
SDAT1 R6805 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-EH55EC/EP,EH56EG SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. SD Card Schematic Diagram...
Page 117
ERJ3GEY0R00V C7520 C7534 0.01 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH55EC/EP,EH56EG TIMER SECTION THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE (3/4) TIMER(1/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 118
WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. C7577 R7619 IC7505 RESET IC-DETAIL BLOCK DIAGRAM D7509 B0JDCE000002 X_SW_5R2V Vref R7623 R7621 100K C7584 F4D55473A013 DMR-EH55EC/EP,EH56EG M N O P Q TIMER SECTION TIMER(2/4) Section (4/4) (Main P.C.B.(4/4)) Schematic Diagram(T)
Page 119
DE:Nicam Decoder Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-EH55EC/EP,EH56EG T:Timer Section:(Page: SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. TIMER(3/4) Section (Main P.C.B.(4/4))
Page 120
A-IN A+IN M:Main Net Section:(Page: AV:A/V I/O Section:(Page: DE:Nicam Decoder Section:(Page: DMR-EH55EC/EP,EH56EG T:Timer Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. TIMER(4/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 121
1000(EP) R7844 680(EP) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH55EC/EP,EH56EG THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Tuner Pack Schematic Diagram...
Page 123
DGND FP50004 DD10 B_IN R_IN OPEN_SW PHOTO_LED CARTRIGE REC INH RESET- CLOSE SW P.C.B.Name Circuit Name Ref.No. Ref.No.50000 SERIES Ref.No.50000,53000,54000, Digital 55000,57000 SERIES P.C.B. Audio I/O Ref.No.54000 SERIES D Net/EPG Ref.No.59000 SERIES Model Select Ref.No.59000 SERIES DMR-EH55EC/EP,EH56EG Interconnection Schematic Diagram...
Page 125
IC1601 C0DBAZZ00132 C0DBAZZ00132 (AL1014) (AL1014) DMR-EH55EC/EP,EH56EG NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Power Supply Schematic Diagram E COMPONENTS.ONLY THE SAME TYPE.
13.3. Main Net (1/4) Section (Main P.C.B. (1/4)) Schematic Diagram (M) LOCATION MAP X_SW_3R3V RESET_5R2V M:Main Net Section:(Page: AV:A/V I/O Section:(Page: DE:Nicam Decoder Section:(Page: T:Timer Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
13.4. Main Net (2/4) Section (Main P.C.B. (1/4)) Schematic Diagram (M) ZJ7402 K9ZZ00001279 QR7401 UNR521300L (UN5213-TX) IC7401 PS11R6V C0CBCYG000 (PQ200WNA1Z K7403 VWJ0795=10 C7439 R7446 2000[D] MAIN NET SECTION (4/4)
Page 129
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE 7403 SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. J0795=10 Q7402 2SD1819A0L R7446 2000[D] UNREG_38V DMR-EH55EC/EP,EH56EG Main Net(2/4) Section (Main P.C.B.(1/4)) Schematic Diagram(M)
13.6. Main Net (4/4) Section (Main P.C.B. (1/4)) Schematic Diagram (M) MAIN NET SECTION (2/4) R7405 Q7401 ERDS2TJ471T 2SD1819AWL R7404 D7403 MA2C165001VT (MA165TA5VT) L7402 G0A220GA0026 R7406 470K LB7407 J0JKB0000012 QR7403 QR74 UNR521500L UNR521 R7403 TO P59001 C7414 C7415 DIGITAL P.C.B. F1H1A105A028 F1K1C105A026 (MODEL SELECT SECTION)
Page 133
UNR521500L TL7401 LOCATION MAP Net Section:(Page: I/O Section:(Page: DMR-EH55EC/EP,EH56EG am Decoder Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. Main Net(4/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Section:(Page: SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 134
IC1510 IC1505 TU +5V SWITCHING REGULATOR XSW +3.3V SWITCHING REGULATOR IC-DETAIL BLOCK DIAGRAM IC-DETAIL BLOCK DIAGRAM Vout VOUT CONT IC1520 IC1506 ANA +5V SWITCHING REGULATOR DR +5V SWITCHING REGULATOR IC-DETAIL BLOCK DIAGRAM IC-DETAIL BLOCK DIAGRAM VOUT VOUT SENSE ON: H ON/OFF REG.
13.8. A/V I/O (2/4) Section (Main P.C.B. (2/4)) Schematic Diagram (AV) C3957 470P R3930 C3958 470P R3989 R3992 R3993 R3991 R3988 R3994 LB3911 R3987 J0JGC0000020 R3990 D3901 MA2C165001VT R3924 R3935 (MA165TA5VT) ERDS2TJ221T JK3901 K1FB242B0005 AV1 2 (TV) (DECODER) R3913 R3912 R3003 F G H N O P...
Page 139
C3059 1000P R4007 82K C3060 LB3008 470P J0JBC0000019 DMR-EH55EC/EP,EH56EG Z AA AB AC AD AE AG AH AI AJ AK AL AM A/V I/O(2/4) Section NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. (Main P.C.B.(2/4)) THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
13.10. A/V I/O (4/4) Section (Main P.C.B. (2/4)) Schematic Diagram (AV) F G H N O P Q R S Z AA AB AC AD AE C4021 35V10 C4019 35V10 R4006 C4027 50V10 C4067 25V47 R3001 TL3001 1/2REF DT C IN C3935 VCC 5V DT Y IN...
Page 143
LOCATION MAP Main Net Section:(Page: A/V I/O Section:(Page: :Nicam Decoder Section:(Page: DMR-EH55EC/EP,EH56EG imer Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. A/V I/O(4/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 147
C7318 0(EC) 16V10(EC) 0(EC) R7317 DMR-EH55EC/EP,EH56EG Nicam Decoder Section NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. (Main P.C.B.(3/4)) THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
13.13. Timer (2/4) Section (Main P.C.B. (4/4)) Schematic Diagram (T) L7501 G0C390JA0055 IP7501 ELESN390JA K5H7512A0010 T7501 G4D1A0000117 C7569 R7614 ECQB1H392KF3 QR7508 UNR521400L IC7505 RESET IC-DETAIL BLOCK DIAGRAM Vref R7621 100K M N O P Q TIMER SECTION (4/4)
Page 151
IMPORTANT SAFETY NOTICE: C0EBJ0000153 COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. (BD485G) WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. C7577 R7619 D7509 B0JDCE000002 X_SW_5R2V R7623 R7621 100K C7584 F4D55473A013 DMR-EH55EC/EP,EH56EG TIMER(2/4) Section (Main P.C.B.(4/4)) Schematic Diagram(T)
13.15. Timer (4/4) Section (Main P.C.B. (4/4)) Schematic Diagram (T) M N O P Q TIMER SECTION (2/4) QR75 UNR52 R7586 D7502 R7583 R7584 B0ACCK000005 4700 (1SS355) R7585 R7587 2R2M 220K C7552 R7588 R7589 220P 100K LB7510 ERJ3GEY0R00V R7624 IC7507 EXT_LINK CH_DOW MOTOR DRIVE...
Page 155
R7642 5600 Main Net Section:(Page: A/V I/O Section:(Page: :Nicam Decoder Section:(Page: DMR-EH55EC/EP,EH56EG imer Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. TIMER(4/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 157
1000(EP) R7844 680(EP) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH55EC/EP,EH56EG THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Tuner Pack Schematic Diagram...
Page 159
R6805 SDAT1 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-EH55EC/EP,EH56EG SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. SD Card Schematic Diagram...
JW7001 [VWJ02F0060VV] KEY3_POWER NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH55EC/EP,EH56EG THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Front(L) Schematic Diagram 13.19. DV Jack Schematic Diagram TO PS57001 DIGITAL P.C.B.
Page 162
IC1505 IC1506 Ref No. MODE PLAY STOP IC1507 IC1510 IC1520 Ref No. MODE PLAY STOP IC1521 IC1522 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE 11.6 PLAY 11.6 STOP 11.6...
Page 163
IC4009 IC4011 Ref No. MODE 11.6 PLAY 11.6 STOP 11.6 IC4012 IC4901 Ref No. MODE 11.6 PLAY 11.6 STOP 11.6 IC7301 Ref No. MODE PLAY STOP IC7301 Ref No. MODE PLAY STOP IC7301 Ref No. MODE PLAY STOP IC7302 IC7401 IC7402 Ref No.
Page 169
IIC BUS TIMER LOGIC PS7801 PP7401 TUN Lch IIC DATA SECTION SIF OUT L OUT IC7501- 2.3V 1.0V RF OUT MUTE TUNER P.C.B. IC4901 OPTICAL (DIGITAL AUDIO OUT) FROM P59001 P7402 IEC OUT DIGITAL P.C.B. DMR-EH55EC/EP,EH56EG Analog Audio Block Diagram...
Page 170
G SBMTP A SBMTP TBUS RXD P7402- XOUT X7501 10MHz IC7507 X SW+12.4V (FAN MOTOR DRIVE) FAN PWM OUT 22 Q7511 (FAN MOTOR DRIVE) FAN MOTOR P1501 P1102 P1103 P1501 P1102 P1103 DMR-EH55EC/EP,EH56EG FAN LOCK H 39 Timer Block Diagram...
Page 171
GREEN (DECODER/EXT) AV2 B AV2 G BLUE CLAMP AV2 V/Y TU7801 VIDEO/Y (EP) U/V TUNER AV2 B Q7802 TUNER CLAMP PP7401 PS7801 VIDEO CLAMP BUFFER AV2 V/Y CLAMP 2.3V (Except (EP)) 1.0V K7809 TUNER P.C.B. DMR-EH55EC/EP,EH56EG Analog Video Block Diagram...
Page 172
IC3001- ,IC4009- ,IC4012- 12,13,14,15 Q1200 (FEED BACK) FROM PWR SAVE TIMER IC7501- 79 SECTION QR7401 :ON) Q1509 (DR+12V OUT) DR+12V IC1200 (ERROR VOLTAGE DET.) FROM DR P ON TIMER IC7501- 42 SECTION COLD QR1501 :ON) DMR-EH55EC/EP,EH56EG Power Supply Block Diagram...
Page 173
PS7801 ON/OFF 2 (RESET) BTL+30V IC7301- 5V(VIF) IC1510 (REG.+5V) VOUT JC REG.+5V D+12V P7402 P59001 FROM 64,66,68,70,72,74 TU P ON TIMER IC7501- 43 SECTION IP50001 DR+12V P7402 P59001 IC50003(+12V) 14,16 DMR-EH55EC/EP,EH56EG DMR-EH55EC/EP,EH56EG Power Supply Block Diagram Power Supply Block Diagram...