NEC MultiSync P654Q User Manual page 44

CHANGE PASSWORD Allows the security password to be changed.
The factory preset password is 0000.
SECURITY
PASSWORD Input security password.
SECURE MODE
OFF The security password is not required when the monitor power is on.
START-UP LOCK The security password is required when the monitor power is on.
CONTROL LOCK The security password is required when a remote control button or a control button on the monitor is pressed.
BOTH LOCK The security password is required when either the monitor is powered on, or a remote control button or a control
button on the monitor is pressed.
IR LOCK SETTINGS Prevents the monitor from being controlled by the wireless remote control.
When ACTIVATE is selected, all settings are activated.
NOTE: IR LOCK SETTINGS is a function intended only for the wireless remote control buttons. This function
does not lock out access to the buttons on the monitor. To return to normal operation, press the "DISPLAY" button
on the remote control and hold it down for more than 5 seconds.
MODE SELECT Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.
UNLOCK All buttons on the remote control are available for normal operation.
ALL LOCK Locks all remote control buttons.
CUSTOM LOCK
Selects which buttons to be locked from POWER, VOLUME, and INPUT button.
Except for CUSTOM LOCK settings, other buttons on the remote control are locked.
POWER:
VOLUME: When UNLOCK is selected, set the minimum and maximum volume between VOL.0 to VOL.100.
INPUT:
CHANNEL: To lock channel buttons on the remote control, select it to LOCK then press ACTIVE, channel
KEY LOCK SETTINGS Prevents the monitor from being controlled by the buttons on the monitor.
When ACTIVATE is selected all of the settings are activated.
NOTE: KEY LOCK SETTINGS is a function intended only for the buttons of the monitor. This function does not
lock out access to all buttons on the remote control. To activate the control key lock function, press the UP button
( ) and the DOWN button ( ) and hold down simultaneously for more than 3 seconds. To resume user mode,
press the UP button ( ) and the DOWN button ( ) and hold simultaneously for more than 3 seconds.
MODE SELECT
Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.
UNLOCK
All buttons are available for normal operations.
ALL LOCK Locks all remote control buttons.
CUSTOM LOCK Selects which buttons to be locked from POWER, VOLUME, and INPUT button.
Except for CUSTOM LOCK settings, other buttons on the remote control are locked.
POWER:
VOLUME: When UNLOCK is selected, set the minimum and maximum volume between VOL.0 to VOL.100.
INPUT:
CHANNEL: To lock channel buttons on the remote control, select it to LOCK then press ACTIVE,
DDC/CI ENABLE/DISABLE: Turns ON or OFF the two-way communication and control of the monitor.
DisplayPort2 input only
PING Confirm successful connection with the network by communicating with a preset IP address.
IP ADDRESS Sets an IP ADDRESS for sending PING.
EXECUTE Checks a reply can be sent to the monitor or not from the IP ADDRESS by sending PING.
IP ADDRESS RESET Resets IP ADDRESS SETTINGS back to factory settings.
When LOCK is selected, the POWER button is locked.
VOLUME (+) button and VOLUME (-) buttons are only available from the minimum volume to the
maximum volume you set.
When LOCK is selected, VOLUME (+) button and VOLUME (-) buttons are locked.
When UNLOCK is selected, choose up to three buttons from DisplayPort1, DisplayPort2, HDMI1,
HDMI2, HDMI3, MEDIA PLAYER, OPTION which you prefer to be unlocked.
The unselected buttons are locked. When LOCK is selected, all INPUT buttons are locked.
CH/ZOOM (+) button and (-) button are locked.
When LOCK is selected, the POWER button is locked.
The PLUS button (+) and the MINUS button (-) are only available from the minimum volume to the
maximum volume you set.
When LOCK is selected, the PLUS button (+) and the MINUS button (-) are locked.
When UNLOCK is selected, the INPUT/SET button is unlocked.
the UP button ( ) and the DOWN button ( ) are locked.
English-42