Pioneer PDP-R05E Service Manual page 146

1
6. MR NG
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
A
1
I N F O R M A T I O N
2
3
4 M R N G
M A I N
5
6
1 M R – PWR
7
2 MO D U
8
3 M A – I I
9
4 M A – I I
10
5 M A – S R
11
6 M A I N
12
13 7 T E M P 2
8
14
15
16
Information on power-down and shutdown of the Media Receiver side is displayed.
B
• Media Receiver NG information
No.
1 Abnormality in module microcomputer communication
2 Abnormality in 3-wire serial communication of the main microcomputer
3 Abnormality in main microcomputer IIC communication
4 Abnormality in main microcomputer communication
5 Abnormality in temperature of the Media Receiver
6 Fan stopped.
7 Abnormality in communication of the digital tuner
C
8 Abnormality in the ASIC power supply on the MR side
• Subcategory information
Type of Shutdown
MA-SRL
MA-IIC
Interval UART
D Communication
7. TEMPERATURE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
1
I N F O R M A T I O N
2
3
T E M P E R A T U R E
4
5
6 T E M P
T E M P
7
E
8
9
F A N
10
11
12
13
14
15
16
TEMP1: The value read from the temperature sensor built into the panel is displayed in the range of 000-255.
Note: Refer to the service manual of the panel.
TEMP2: The value read from the temperature sensor built into the Media Receiver is displayed in the range of 000-255.
For reference, the approximate value for 60°C is 86 and for 35°C is 67.
Reference: When TEMP2 exceeds 100 (about 78°C), SD LED flash 11 times.
F FAN: The value of the Fan output is displayed. At shipment, the output is controlled in 2 steps, and the value for
strong output is set to about 131, and the value for weak output is set to about 93.
146
1
2
V D 1 – 0 1 3 – N T V – S T 1
S U B
– – – – – – 0 0 1 5 1 H 2 1 M
L E – – – – – – 0 0 0 7 3 H 4 5 M
C F E 2 0 0 0 3 1 H 5 0 M
C A V – S W 2 0 0 0 1 3 H 0 3 M
L I C 3 0 0 0 0 2 H 5 2 M
– – – – – – 0 0 0 0 1 H 5 8 M
– – – – – – 0 0 0 0 0
Type of Failure
Subcategory
IF microcomputer (IC8702), IC2 (IC7004), IC3 (IC7101)
MA-EEP (IC7205), IC1-M (IC6107), IC1-S (IC6255), HDMI1
(IC6801), HDMI2 (IC6881)* , AD-M (IC6402), AD-S (IC6602),
2
IC6 (IC6951), CCD (IC8903)* , FE1 (U7501), FE2 (U7502)*
2
AV-SW1 (IC8002), AV-SW2 (IC8005), TX-COM (IC8904)*
MPX (IC7502)* , TX-BSY(IC8904)*
3
PS/RST
RETRY
CD-COM
CD-DEV
CD-RST
V D 1 – 0 1 3 – N T V – S T 1
1 : 1 2 8
2 : 1 4 9
:
: 1 2 5
2
3
H 0 7 M
H M
On-Screen Display
* : U.S. model only
2
,
* : Europe model and General area model
2
3
,
3
, AV-EEP
3
No power, or reset status continued
The signal 0x02 (ready) has not been received.
PC Card Module Communication
PC Card Module
PC Card Reset NG
PDP-R05E
3
4
Remarks
(MAIN)
MODULE
MA-SRL Subcategories exist.
MA-IIC Subcategories exist.
MAIN
TEMP2
FAN
UART Subcategories exist.
M-DCDC
Remarks
4