Cleaning And Maintenance; Technical Data - HSM securio P 36 Operating Instructions Manual
Hide thumbs
Also See for securio P 36:
- Operating instructions manual (181 pages) ,
- Instruction manual (93 pages) ,
- Operating instructions (4 pages)
Table of Contents
Advertisement
Available languages
Available languages
Cleaning and maintenance
Switch off the shredder and pull out the mains plug.
When cleaning only use a soft cloth and a mild
soap-water solution. However, no water must enter
the equipment.
Check that the door switch is working properly:
Warning!
If the following procedure cannot be
performed, switch off the document
shredder, disconnect the mains plug
and contact customer service.
Technical data
Cutting type
Shred size (mm)
Sa fe ty ra ting DIN 32757 – 1
Cutting ca pa ci ty (sheets), DIN A4
Weight
Cutting speed
Lo ading width
Voltage
Power for the maximum number of sheets
Dimensions W x D x H (mm)
Volume of the shredded paper container
Noise level (Idle running/ load)
* HSM-specifi cation
EC declaration of conformity
Machinery directive 98 / 37 / EC
EMC directive 2004 / 108 / EC
Low voltage directive 2006 / 95 / EEC
The manufacturer HSM GmbH + Co. KG, Austraße 1 - 9, D-88699 Frickingen hereby declares that the document shredder
SECURIO P36 complies with the EC directives listed above, including all modifi cations that apply.
Applied standards and technical specifi cations:
•
EN 55014-1:2000 + A1:2001 + A2:2002
•
EN 55014-2:1997 + A1:2001
•
EN 61000-3-2:2000
•
EN 61000-3-3:1995 + A1:2001
•
EN 61000-4-2:1995 + A1:1998 + A2:2001
•
EN 13857
Frickingen, 6.4.2009
Josef Käppeler - Technical Director
ose
This explanation only refers to the state of the machine when it was fi rst put into use. Subsequent modifi cations are not taken into
account.
14
70 g/m
2
80 g/m
2
se
se
se
se
se
se
se
s
s
s e
sef
se
se
se
se
s e
se
s
f
f
f
f
f
f
f
f
f
f
f
f
f
f
f
f
f
K
K
Kä
K
ppel
el
el
el
el
el
el
el
el
el
el
el
eler
el
el
l
l
l
l
l
er
er
er
er
er
er
er
er
er
er
er
er
er
er
er
r
r
r
r
- Techni
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
t
t
t h
t
t
t
t
t
t
t
t
t
t
e stat
t
t
t
t
t
t
t
t
t
t
t
t
t
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
o
o
o f
o
o
o
o
o f
o f
o
o
o
o
o
o
of
of
of
o
the mac
• Insert the mains plug and switch on the shredder.
• Feed in a sheet of paper and open the front door
while the paper is being drawn in.
The cutting unit must turn off immediately and the
"door open" indicator must light up.
• Close the door.
The cutting unit must not yet restart.
• Pull the paper out of the feed opening. The light
barrier must be clear.
• Switch off the machine and then switch back on.
The cutting unit starts when paper is fed in.
Strip cut
5.8
3.9
2
2
47 - 49
37 - 39
39 - 41
31 - 33
64 kg
90 mm/s
230 V, 50 Hz
580 x 550 x 936
58 - 59 dB(A) / 60 - 61 dB(A)
•
EN 61000-4-4:1995 + A1:2001 + A2:2001
•
EN 61000-4-5:1995 + A1:2001
•
EN 61000-4-6:1996 + A1:2001
•
EN 61000-4-11:1994 + A1:2001
•
EN 60950-1:2006
Cross cut
4.5 x 30
1.9 x 15
3
4
29 - 31
18 - 20
25 - 27
15 - 17
68 kg
100 mm/s
330 mm
1.800 W
145 l
1 x 5
Level 6*
9
7
0906
Advertisement
Table of Contents
