Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Apollo Mini-Mist PRO
Summary of Contents for Apollo Mini-Mist PRO
- Page 1 Mini-Mist® PRO INSTRUCTION MANUAL (Not Suitable for Continuous Use) DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these instructions carefully and keep for your reference. ©2011 (Apollo Sprayers International, Inc.)
-
Page 2: Table Of Contents
Take a minute to read and understand how to operate your new T100 Mini-Mist Pro® tanning system and you will be able to provide the perfect tan with every application. -
Page 3: General Safety Information
General Safety Information: Read all instructions and safety precautions before operating the unit. THIS INDICATES A CONDITION THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS IGNORED. THIS INDICATES A CONDITION THAT COULD CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS IGNORED. - Page 4 General Safety Information cont’d.: • Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube and fittings. The Spray Gun does not function when clogging occurs. • When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid tipping.
-
Page 5: Set Up And Operate Your T100 Spray Tan System
Next, locate the male end of the air hose and connect it to the female quick connect on the T100 Mini-Mist tanning system. ® a. To insert the coupler pull back on the ring of the black coupler located on the Mini-Mist Pro tanning system ®... -
Page 6: Prepare The T6000 Spray Gun
If you have just finished spraying, the connector may be hot. Allow the T100 Turbo unit to cool down for about 10 minutes before disconnecting the air hose from the turbo unit. Use Caution! Prepare the T6000 Spray Gun 1. Follow the diagram to prepare the Spray Gun a. -
Page 7: Adjusting The Spray Gun
Adjusting the Spray Gun a. Locate the Solution Flow Knob (#10) on the T6000 diagram. b. Turning the Solution Flow Knob clockwise reduces and will eventually stop the flow of solution. DO NOT over-tighten the screw as this will cause damage to the end of the needle. Once the trigger cannot be pulled back there is no point in tightening the screw down more, this will only damage the end of the needle. -
Page 8: Spraying
Spraying You are now ready to begin misting. The ON/OFF Switch is located under the carry handle of the T100 Turbo Unit. Turn it on. You will hear a sound similar to a vacuum cleaner. You may also notice that air is now blowing out of the front of the spray gun. -
Page 9: Maintenance
Maintenance 1. T100 Turbo Unit. a. The only maintenance necessary on the turbo unit is cleaning and/or changing the filter element. The filter should be removed and rinsed out at least once daily or at least every 4 tanning sessions. The filter housing and filter are located on the underside of the T100 Turbo Unit. -
Page 10: Troubleshooting
d. Rinse the cup under warm running water until clean. Fill the cup about ¼ full with water. Reconnect Spray Gun to Air Hose. Turn on the T100 Turbo Unit. Direct the Spray Gun to a safe area and spray the clean warm water through the Spray Gun until the cup is empty. Turn off the T100 ™Turbo Unit. - Page 11 A2. Check that there is no solution bubbling or leaking around the cup. A3. Check to make sure the cup gasket is not damaged or missing from the cup lid. A4. Check to make sure there is no dried solution in the end of the fluid nozzle. Turn T100 Turbo unit OFF.
-
Page 12: Diagram
Diagram... -
Page 13: Warranty & Technical Support
Warranty and Technical Support For all other technical questions please call your local distributor or Apollo Sprayers Inc. for technical support. USA Technical Support: Available Monday-Friday, 8am-4pm, PST. Apollo Sprayers International, Inc. 1030 Joshua Way Vista, CA 92081 Voice: 760-727-8300...