Table of Contents
Advertisement
Quick Links
Sítio dos Barrabés, Armazém Nave Y, Caixa Postal 908-Z, 8150-016 São Brás de Alportel - PORTUGAL | Tel: +351 289 896 560
Email: info@globalfire-equipment.com | Technical Support: techs@globalfire-equipment.com | www.globalfire-equipment.com
CONFIGURATION MANUAL
GENERAL DESCRIPTION
TECHNICAL SPECIFICATIONS
CONNECTION DIAGRAM
PANEL CONFIGURATION
BMS port configuration - ODYSSEY Protocol
INTERFACE CONFIGURATION
LEDs behaviour
Startup behaviour
Operation behaviour
Configuration using Wi-Fi with module in AP MODE
Factory reset and Wi-Fi configurations reset
Connecting with Ethernet cable (RJ45)
Email or SMS Alerts
Service www.clickatell.com (SMS)
Firmware update by micro SD card (recommended method)
Firmware update via Wi-Fi
WEBPAGE ACCESS AND CONFIGURATION
FREQUENTLY ASKED QUESTIONS - DIAGNOSTIC
Advanced Debug Mode
Unlock ports
Troubleshooting guide lines
INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622
INT-TCP/IP-WEB
REMOTE ACCESS
TCP/IP INTERFACE
GLOBAL FIRE EQUIPMENT S.A.
MANUAL 210622
MADE IN PORTUGAL - EU
2
2
3
3
3
4
4
4
4
5
8
8
9
9
9
10
11
13
13
13
13
1
Advertisement
Table of Contents
Related Manuals for Global Fire Equipment INT-TCP/IP-WEB
Summary of Contents for Global Fire Equipment INT-TCP/IP-WEB
- Page 1 Service www.clickatell.com (SMS) Firmware update by micro SD card (recommended method) Firmware update via Wi-Fi WEBPAGE ACCESS AND CONFIGURATION FREQUENTLY ASKED QUESTIONS - DIAGNOSTIC Advanced Debug Mode Unlock ports Troubleshooting guide lines INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
-
Page 2: General Description
GENERAL DESCRIPTION The INT-TCP/IP-WEB is an interface that extends new advanced features and functionalities to Chameleon Panels (GEKKO and OCTO+). Its enhanced hardware allows for an easier integration with existing LANs via Wi-Fi or optional Ethernet cable. An SD Card socket permits the interface to hold and store valuable data or simple firmware upgrades when needed. This is extremely handy on network debug and log needed situations. -
Page 3: Connection Diagram
► to configure CH2 : ODYSSEY ADD:01 Please refer to panels Installation Warning: Panel will reboot at the end. Manual to learn more about the BMS channels. Fig. 1 - BMS Menu INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622... -
Page 4: Interface Configuration
No power LED 2 (Yellow) LED 1 (Red) The interface was reset by the switch. Wait 5 seconds. FLASHING x2 Without Odyssey protocol. No communication. FLASHING x3 No Internet. FLASHING Normal Mode INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622... - Page 5 As an example in the image above there is one interface connected (MAC address), select the interface to your Wi-Fi network, it’s an open Wi-Fi network without the need of a password. INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 6 14) DNS_1- configure the primary DNS address for cable connection and DHCP disconnected. 15) DNS_2- configure a secondary DNS address for RJ45 connection and DHCP disconnected. 16) BROKER: remote.createc.pt 17) PORT: 8883 18) USER: B5D7F3 INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 7 If it fails reconnect to AP to try again. make several attempts before going into access point mode. Version Firmware: 1.2.1 You can now access remotely to https://www.createc.pt/gk1/gfe/en/ follow the “CONFIGURATION: WEB PAGE” section of this manual. INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 8 The connection to the internal network should allow the interface to be connected by DHCP with access to the exterior. If this is not possible the interface cannot communicate with the internet broker (external server). INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 9 Save the update firmware file "upgrade.bin" to the micro SD card. Turn interface power OFF, and insert the micro SD card into its socket. Turn interface power ON. If the file is valid the update starts Automatically. INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 10 The interface in normal operation, if you press the switch for 2 seconds, within 2 to 4 seconds the interface will reset. At the time of the reset the switch should be released. INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 11 The connection between the interface and the internet broker (external server) as well as the web page to the server is secured by SSL. Firefox browser is not supported and it will not get connection, due to the browser not accepting data in WSS secure websockets. INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 12 Read - Read parameters of previously saved installation. Place 'Installation' name and click on 'Read’ Save - Save parameters after defining ‘installation name’ Clear Item - Delete loaded installation parameters Clear All - Delete all saved installation parameters Restart - Reload webpage Exit - Exit webpage INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 13 If at any time, the communication between the interface and webpage is not achieved, please check the following: Unlocking ports For closed networks, the ports that need to be unlocked are: ● 9001- web page ● 8883- interface Troubleshooting guide lines I = INTERFACE G = GENERAL INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 14 - 30 minutes is the maximum allowed time for for configurations to be sent to after 30 minutes.. programming. interface. - Interface will initialised automatically. Check interfaces power supply. All LEDs are OFF. Hardware fault Replaced interface. INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
- Page 15 GLOBAL FIRE EQUIPMENT S.A. Sítio dos Barrabés, Armazém Nave Y, Caixa Postal 908-Z, 8150-016 São Brás de Alportel - PORTUGAL | Tel: +351 289 896 560 Email: info@globalfire-equipment.com | Technical Support: techs@globalfire-equipment.com | www.globalfire-equipment.com INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622...
Need help?
Do you have a question about the INT-TCP/IP-WEB and is the answer not in the manual?
Questions and answers