Table of Contents
Advertisement
Quick Links
Global Fire Equipment // g lobalfire.pt
ORION MINI-REP V2
Conventional Repeater Panel
Installation, OPERATION & MAINTENANCE MANUAL
GENERAL DESCRIPTION
The ORION MINI-REP V2 will provide remote control and system display status from multiple locations, to an ORION based
Conventional Fire Alarm System. Its reduced dimensions make it ideal for installation in reception areas or security booths
where it would be impractical and unattractive to install a full size control panel. ORION MINI-REP V2 can be connected to
the ORION Conventional Panel using 4 different interconnecting technologies: RS232, RS485, (Fiber Optics and TCP/IP
options are under development).
The unit is provided as standard with an RS232 interface. Power for the ORION MINI-REP V2 can be supplied from the
control panel's auxiliary power output or from an external 24 Volt DC power supply if required.
IMPORTANT SAFETY NOTES
● This equipment must only be installed and maintained by a suitably qualified and technically competent person.
● A basic knowledge and training in the installation of Fire Detection Systems is assumed.
● The Fire Detection System should be designed by a suitably qualified person with reference to the Local Regulations and
Guidance from the fire Officer where applicable.
● All wiring should be carried out with no power present in any part of the Fire Detection System.
COMPATIBILITY NOTE
ORION-MINI REP V2 repeater panel is only compatible with O RION panels that exhibit the following sequential LED pattern
during RESET.
ma_orionminirepv2_01_020000_en_201015
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Global Fire Equipment ORION MINI-REP V2
Summary of Contents for Global Fire Equipment ORION MINI-REP V2
- Page 1 Conventional Fire Alarm System. Its reduced dimensions make it ideal for installation in reception areas or security booths where it would be impractical and unattractive to install a full size control panel. ORION MINI-REP V2 can be connected to the ORION Conventional Panel using 4 different interconnecting technologies: RS232, RS485, (Fiber Optics and TCP/IP options are under development).
- Page 2 Refer to ORION panel’s installation manual for further details about operation. f) Connect Power Supply. ORION MINI-REP V2 requires 24V DC supply voltage, which can be derived from the control panel auxiliary supply output. Do not apply supply voltage until installation is complete.
- Page 3 Global Fire Equipment // g lobalfire.pt ma_orionminirepv2_01_020000_en_201015 CONNECTION DIAGRAMS ORION MINI-REP V2: General hardware and connections layout...
- Page 4 ORION MINI-REP V2 - RS-232 interface One single repeater connection Maximum of 1 ORION MINI-REP V2 with INT-RS232-WIRE (for multi-rep use INT-RS485-DTL). NOTE: Maximum distance between Panel ORION MINI-REP should be 100 meters. ORION MINI-REP V2 - RS-485 interface Multi repeater connection until a maximum of 4 ...
- Page 5 Global Fire Equipment // g lobalfire.pt ma_orionminirepv2_01_020000_en_201015 PANEL STATUS INDICATORS & CONTROLS STATUS FIRE – LED used to indicate any FIRE ALARM condition present on panel. FAULT – LED used to indicate Fault condition present on panel. In case of communication fault between ORION and ORION MINI REP V2 or any other peripheral, Fault LED will flash at a rate of once per second.
- Page 6 Global Fire Equipment // g lobalfire.pt ma_orionminirepv2_01_020000_en_201015 FAULTS SUPPLY FAULT – This LED will be ON whenever the Main Supply has been removed or has dropped below 20 Volts. BATTERY FAULT – Indicates that there is low voltage level on the batteries or the battery charger circuit has failed.
- Page 7 When more than one Repeater is needed, each repeater has to be addressed. To address the ORION MINI-REP V2 please follow the steps below: 1. Install and connect the repeater (refer to I NSTALLATION s ection of this manual).
Need help?
Do you have a question about the ORION MINI-REP V2 and is the answer not in the manual?
Questions and answers