Taiden HPA-160D/02 Installation And Operation Manual

Taiden HPA-160D/02 Installation And Operation Manual

Digital audio power amplifier

Advertisement

Quick Links

Digital Audio Power Amplifier
Digital Audio Power Amplifier w/Dante
Installation and Operation Manual
V 1.1

Advertisement

Table of Contents
loading

Summary of Contents for Taiden HPA-160D/02

  • Page 1 Digital Audio Power Amplifier Digital Audio Power Amplifier w/Dante Installation and Operation Manual V 1.1...
  • Page 2: Table Of Contents

    Contents Important Safety Instructions ...................... II Installation & User Guide ......................IV Chapter 1 Overview ........................1 Chapter 2 Functions and indications ..................2 Chapter 3 Connection and operation ..................4 3.1 Input/Output ..............................4 3.2 Connection ................................ 4 3.3 Operating instructions ............................5 3.3.1 Protect speaker ............................
  • Page 3  To protect your hearing, avoid high pressure level on earphones. Adjust to a lower and convenient level If any detailed information is needed, please contact your local agent or TAIDEN service center in your region.  Any feedback, advice and suggestion about the products is appreciated TAIDEN is the registered trademark of TAIDEN Co., Ltd.
  • Page 4: Important Safety Instructions

    Service Center. The MAINS plug serving as a disconnection device, 20. All TAIDEN products are guaranteed for definite time (see the WARRANTY CARD for details) excluding the should be easy to operate. The apparatus should be connected to the MAINS...
  • Page 5 Important Safety Instructions The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: To reduce the risk of fire or electric shock, DO NOT expose units to rain or moisture.
  • Page 6: Installation & User Guide

    Digital Audio Power Amplifier. Chapter 4:Specifications Main technical parameters of Digital Audio Power Amplifier. This manual is applicable to: HPA-160D/02 Digital Audio Power Amplifier (2 channels, 2×200 W, Dante interface) HPA-160A/02 Digital Audio Power Amplifier (2 channels, 2×200 W)
  • Page 7: Chapter 1 Overview

     efficiency under conventional conditions is more than 2×RJ45 socket for digital audio transmission via 80%. Dante networking (HPA-160D/02)  1 Line In and 1 Line Out (∅6.4 mm phone jack)  Features: The user can access the IP address of power ...
  • Page 8: Chapter 2 Functions And Indications

    Chapter 2 Functions and indications Front panel of HPA-160D/02 Front panel of HPA-160A/02 Rear panel Digital audio power amplifier Figure 2.1...
  • Page 9  ∅6.4 mm TRS socket for balance signal input. 1. Reset 9. Line In 2  Press 3 times continuously restore PA to factory  ∅6.4 mm TRS socket for mono or stereo signal and rebooted. 10. Line In 2 2.
  • Page 10: Chapter 3 Connection And Operation

    Chapter 3 Connection and operation 3.1 Input/Output Connecting knowledge:  For input, use the shielded wire with high shielding layer density;  Balanced connection reduce noise interference;  For unbalanced connection, the shorter the cable is the better. Maximum length does not exceed 3 meters;...
  • Page 11: Operating Instructions

    To Dante network Figure: bridge mode Note: HPA-160A/02 has no Dante function. 3.3 Operating instructions Please confirm before installation: mixer input channel, the filter frequency is set  The power cord not connected to the power below the minimum fundamental frequency of the socket;...
  • Page 12 PA output protection and premature clipping may damage the speaker; When PA is switched on, the output interface may have a fatal voltage. Note: TAIDEN is not responsible for any damage caused by excessive use of other system components.
  • Page 13: Web Control

    Gateway 192.168.1.1 Netmask 255.255.0.0 Input IP address in browser to enter web server, or search HPA-160/02 with TAIDEN Device Discovery, as shown below: Figure: search device How to enter Web server:  Input default IP address: 192.168.1.60 (if cannot modify the network parameters) in the web browser;...
  • Page 14 Web interface for HPA-160D/02 is shown below, and HPA-160A/02 has no Dante function. Two icons at the top-right are "Channel Parameters ( )" and "System Setting ( )".  Channel Parameters When input mode is “Balance”, the web interface will display channel 1/2/3; when input mode is “Mono/Stereo”, the web interface will display channel 1/2/3/4;...
  • Page 15 Figure: PEQ of input channel Volume gain of loudspeaker Parameters setting for all output: Line out, Speaker out, Dante out Figure: PEQ of output channel GEQ: 31 segment graphical equalization, drag pushers to adjust equilibrium parameter. It is only for output channel. You can also enable/disable low-cut and high-cut features, and set their frequency point.
  • Page 16 Parameters setting for all output: Line out, Speaker out, Dante out Figure: GEQ of output channel DRC: DRC (dynamic ratio compressor) interface is shown as below. It is only for output channel. Threshold, Ratio, Attack Time and Decay Time can be set. Parameters setting for all output: Line out, Speaker out, Dante out Figure: DRC of output channel Speaker Output:...
  • Page 17 Figure: Speaker output setting  System Setting Device information and Dante information can be viewed in system setting page, the following items can be modified: Device name;  DHCP: ON/OFF, when DHCP is OFF, IP Address, Netmask and Gateway can be set; ...
  • Page 18 Figure: parameters of PA...
  • Page 19: Chapter 4 Specifications

    Chapter 4 Specifications HPA-160/02 4 Ω / 6 Ω 2×200 W ( 2×160 W (8 Ω) 1×400 W (8 Ω, Bridge) Rated power 4 Ω / 6 Ω (EIAJ THD=1%,1 kHz) 1×400 W ( , Bridge) 1×400 W (70 V Constant voltage) 1×400 W (100 V Constant voltage) Voltage gain (8 Ω, 1 kHz) 24.0 dB...
  • Page 20: Chapter 5 Rs-232 Control

    <channel> <volume> Enter" <channel> stands for audio channel, details to the following table <volume> stands for audio volume, 0x80: mute, 0~60 for -30 dB ~30 dB 1)HPA-160D/02 input interface: LineIn(Balance/Stereo/Mono×2), Dante1,Dante2 Input channel Output channel Input source Input mode Dante1...
  • Page 21 TAIDEN INDUSTRIAL CO., LTD. 6/F, Block B, Future Plaza, 6060 Qiaoxiang Rd, Nanshan District, Shenzhen, China Copyright by TAIDEN P.C.: 518053 Last Revision: 04/2020 Website: http://www.taiden.com...

Table of Contents